Proxxon DH 40 Manual
  1. Manuals
  2. Brands
  3. Proxxon Manuals
  4. Planer
  5. DH 40
  6. Manual
Proxxon DH 40 Manual

Proxxon DH 40 Manual

Hide thumbs Also See for DH 40:
Table of Contents

Advertisement

Quick Links

See also: Operating Manual , Manual
DH 40
Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DH 40 and is the answer not in the manual?

Questions and answers

Ed Podlewski
February 2, 2025

I need to change the rubberised spool ,do I need to take it apart completely?

0

Subscribe to Our Youtube Channel

Related Manuals for Proxxon DH 40

Summary of Contents for Proxxon DH 40

  • Page 1 DH 40 Manual...
  • Page 2 Fig. 1a Fig. 1b Fig. 2 Fig. 2a Fig. 3 Fig. 4 Fig. 5 Fig. 6 - 3 -...

  • Page 3: Table Of Contents

    Pay attention to the surrounding conditions. PROXXON shall not be liable for the safe operation of the Use the planer only in dry environments and never in the equipment in the case of: vicinity of combustible liquids or gases.

  • Page 4: Description Of The Machine

    Do not use the ca- ble to pull the plug from the socket and do not lift the unit The PROXXON DH 40 thickness planer is a unit for fine by means of the cable. Pay attention to cleanliness: Pro- planing work with a particularly uniform and smooth fin- tect the cable from grease and oil.

  • Page 5: Scope Of Supply

    1. To erect the planer, remove the machine from the packaging and place on a flat and level foundation.En- 1 off Thickness planing machine DH 40 sure that the machine is standing safely and that it 1 off Pin for height adjustment hand wheel cannot fall during operation.

  • Page 6: Planing

    Stand in front of the device while working! Never work with your DH 40 from the side or If the workpiece is drawn in but comes to a stop after a even from the back. Ensure sufficient stability while you...

  • Page 7: Adjusting The Cutters

    Risk of injury! tion of the cutter holders (for example, dismantling the cutter holder or previous accidental maladjustment) 1. Unscrew the blocking screw 2 (fig. 5). please proceed as follows: Caution: 1. Remove the locking screw 2 (Fig. 5) and open the cov- Never operate the planing machine with parts of the er 4.

  • Page 8: Lubrication

    PROXXON S.A. 6-10, Härebierg Lubrication L-6868 Wecker Normally, no further lubrication is necessary for opera- Product designation: DH 40 tion. Avoid oiling or greasing the height adjustment spin- Article No.: 27040 dles; remember that lubricants can mix with planing dust and will then have to be removed.
  • Page 9 - 78 -...
  • Page 10 Base 27040-01-01 Frame, left 27040-01-02 Frame, right 27040-01-03 Axle for gear wheels 27040-01-04 Plate 27040-01-05 Screw 27040-01-06 Screw 27040-01-07 Casing cover, left 27040-02-01 Casing cover, right 27040-02-02 10 Chipping notch 27040-02-03 11 Cover for insert 27040-02-04 12 Axle 27040-02-05 13 Screw 27040-02-06 14 Screw 27040-02-07...
  • Page 11 Roll, knurled 27040-03-01 Bushing, loose 27040-03-02 Pulley 27040-03-03 Set screw 27040-03-04 Spring 27040-03-05 - 80 -...
  • Page 12 Roll, bubberised 27040-04-01 Gear wheel, 64 teeth 27040-04-02 Poully 27040-04-03 Bushing 27040-04-04 Set screw 27040-04-05 Set screw 27040-04-06 Toothed belt 27040-04-07 - 81 -...
  • Page 13 Kick.back-finger 27040-05-01 Axle 27040-05-02 Limit plate 27040-05-03 Washer 27040-05-03 Circlips 27040-05-03 - 82 -...
  • Page 14 Plane table 27040-06-01 Counter plate 27040-06-02 Gear wheel 36 teeth 27040-06-03 Gear wheel 36 teeth 27040-06-04 Gear wheel 90 teeth 27040-06-05 Bearing block 27040-06-06 Shaft 27040-06-07 Screw 27040-06-08 Screw 27040-06-09 10 Split pin 27040-06-10 12 Washer 27040-06-12 13 Cap nut 27040-06-13 14 Washer 27040-06-14...
  • Page 15 Motor 27040-07-01 Gear drive 140/32 teeth 27040-07-03 Gear drive 140/24 teeth 27040-07-04 Poully 27040-07-05 Holding plate 27040-07-02 Holding plate 27040-07-06 7 Screw 27040-07-07 8 Screw 27040-07-08 9 Washer 27040-07-09 10 Circlips 27040-07-10 11 Set screw 27040-07-11 12 Toothed belt 27040-07-12 16 Switch 27040-07-16 17 Power supply cord...
  • Page 16 Cutter spindle 27040-08-01 Poully 27040-08-02 Ball Bearing 27040-08-03 Wave spring 27040-08-04 - 85 -...
  • Page 17 Service note All PROXXON products are thoroughly inspected after production. Should a defect occur nevertheless, please contact the dealer from whom you purchased the product. Only the dealer is responsible for handling all legal warranty claims which refer exclusively to material and manufacturer error.

Table of Contents