Table of Contents
Advertisement
10.6 Making coffee using coffee beans
Important!
Do not use caramelised or candied coffee beans as they could
stick to the coffee mill and make it unusable.
1. Fill the container (A7) (fig. 12) with coffee beans;
2. Place under the coffee spouts (A14):
- 1 cup, if you want to make 1 coffee (fig. 9);
- 2 cups if you want 2 coffees.
3. Lower the spouts as near as possible to the cup. This makes
a creamier coffee (fig. 13);
4. Press the button corresponding to the number of coffees
required (1 cup
14)
5. Preparation begins. The amount of coffee selected appears
on the display (B1) together with a progress bar which
gradually fills as preparation progresses.
Please note:
•
While the machine is making coffee, delivery can be inter-
rupted at any moment by pressing any button.
•
At the end of delivery, to increase the quantity of coffee in
the cup, just press and hold (within 3 seconds) one of the
coffee buttons (
or
Once the coffee has been made, the appliance is ready to make
the next drink.
Please note:
•
Various alarm messages could be displayed while using
the appliance (FILL TANK, EMPTY GROUNDS CONTAINER,
ETC.). Their meaning is explained in section "19. Displayed
messages".
•
For hotter coffee, see section "10.5 Tips for a hotter coffee".
•
If the coffee is delivered a drop at a time, too weak and not
creamy enough or too cold, read the tips in section "20.
Troubleshooting".
10.7 Making coffee using pre-ground coffee
Important!
•
Never add pre-ground coffee when the machine is off or it
could spread through the inside of the machine and dirty
it. This could damage the appliance.
•
Never use more than 1 level measure (C2) or it could dirty
the inside of the coffee machine or block the funnel (A6).
Please note:
If you use pre-ground coffee, you can only make one cup of
coffee at a time.
1. Press the
button (B6) (fig. 8) until "Pre-ground"
appears on the display (B1).
B7 or 2 cups
B8) (figs. 10 and
).
2. Make sure the funnel is not blocked, then add one level
measure of pre-ground coffee (fig. 15).
3. Place a cup under the coffee spouts (A14) (fig. 9).
4. Press the 1 cup coffee button
5. Preparation begins. The amount of coffee selected appears
on the display together with a progress bar which gradual-
ly fills as preparation progresses.
Please note:
If "Energy Saving" mode is active, you may have to wait a few
seconds before the first coffee is delivered.
11. MAKING CAPPUCCINOS AND MILK-BASED
COFFEES
Please note:
•
To avoid milk with poor froth or large bubbles, always clean
the milk container lid (D2) and hot water connection noz-
zle (A13) as described in sections "11.6 Cleaning the milk
container after use", "13.10 Cleaning the milk container"
and "13.11 Cleaning the hot water/steam connection
nozzle".
11.1 Filling and attaching the milk container
1. Remove the lid (D2) (fig. 16);
2. Fill the milk container (D3) with a sufficient quantity of
milk, not exceeding the MAX level marked on the contain-
er (fig. 17). Each mark on the side of the container corre-
sponds to 100ml of milk;
Please note:
•
For a denser more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
•
If "Energy Saving" mode is enabled, you may have to wait
a few seconds before the first cappuccino is delivered.
3. Make sure the milk intake tube (D4) is correctly inserted in
the bottom of the milk container lid (fig. 18);
4. Place the lid back on the milk
container;
5. Remove the hot water spout (C6)
from the connection nozzle (A13)
(fig. 19);
6. Attach the container to the con-
nection nozzle and push as far as it will go (fig. 20). The
machine emits a beep (if enabled);
7. Place a sufficiently large cup under the coffee spouts (A14)
and frothed milk spout (D5). Adjust the length of the milk
spout. To move it nearer the cup, simply pull it downwards
(fig. 21);
8. Follow the instructions below for each function.
14
(B7)(fig. 10).
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
