Advertisement
Operation Guide 3468
•
Watches that do not have WATER RESIST or WATER RESISTANT marked on the
back cover are not protected against the effects of sweat. Avoid using such a watch
under conditions where it will be exposed to large amounts of sweat or moisture, or
to direct splashing with water.
•
Even if a watch is water resistant, note the usage precautions described below.
Such types of use reduce water resistance performance and can cause fogging of
the glass.
− Do not operate the crown or buttons while your watch is submersed in water or
wet.
− Avoid wearing your watch while in the bath.
− Do not wear your watch while in a heated swimming pool, sauna, or any other high
temperature/high humidity environment.
− Do not wear your watch while washing your hands or face, while doing housework,
or while performing any other task that involves soaps or detergents.
•
After submersion in seawater, use plain water to rinse all salt and dirt from your
watch.
•
To maintain water resistance, have the gaskets of your watch replaced periodically
(about once every two or three years).
E-50
Band
•
Tightening the band too tightly can cause you to sweat and make it difficult for air to
pass under the band, which can lead to skin irritation. Do not fasten the band too
tightly. There should be enough room between the band and your wrist so you can
insert your finger.
•
Deterioration, rust, and other conditions can cause the band to break or come off of
your watch, which in turn can cause band pins to fly out of position or to fall out. This
creates the risk of your watch falling from your wrist and becoming lost, and also
creates the risk of personal injury. Always take good care of your band and keep it
clean.
•
Immediately stop using a band if you even notice any of the following: loss of band
flexibility, band cracks, band discoloration, band looseness, band connecting pin
flying or falling out, or any other abnormality. Take your watch to your original retailer
or to a CASIO service center for inspection and repair (for which you will be charged)
or to have the band replaced (for which you will be charged).
E-52
Magnetism
•
Though a digital watch normally is not affected by magnetism, very strong
magnetism (from medical equipment, etc.) should be avoided because it can cause
malfunction and damage to electronic components.
Electrostatic Charge
•
Exposure to very strong electrostatic charge can cause your watch to display the
wrong time. Very strong electrostatic charge even can damage electronic
components.
•
Electrostatic charge can cause the display to go blank momentarily or cause a
rainbow effect on the display.
Chemicals
•
Do not allow your watch to come into contact with thinner, gasoline, solvents, oils, or
fats, or with any cleaners, adhesives, paints, medicines, or cosmetics that contain
such ingredients. Doing so can cause discoloration of or damage to the resin case,
resin band, leather, and other parts.
E-54
•
Leaving your watch wet for long periods can cause fluorescent color to fade. Wipe
the watch dry as soon as possible after it becomes wet.
•
Semi-transparent resin parts can become discolored due to sweat and dirt, and if
exposed to high temperatures and humidity for long periods.
•
Daily use and long-term storage of your watch can lead to deterioration, breaking, or
bending of resin components. The extent of such damage depends on usage
conditions and storage conditions.
Leather Band
•
Allowing your watch to remain in contact with other items or storing it together with
other items for long periods while it is wet can cause the color of the leather band to
transfer to the other items or the color of the other items to transfer to the leather
band. Be sure to dry off your watch thoroughly with a soft cloth before storing it and
make sure it is not in contact with other items.
E-56
Bacteria and Odor Resistant Band
•
The bacteria and odor resistant band protects against odor generated by the
formation of bacteria from sweat, which ensures comfort and hygiene. In order to
ensure maximum bacteria and odor resistance, keep the band clean. Use an
absorbent soft cloth to thoroughly wipe the band clean of dirt, sweat, and moisture.
A bacteria and odor resistant band suppresses the formation of organisms and
bacteria. It does not protect against rash due to allergic reaction, etc.
Liquid Crystal Display
•
Display figures may be difficult to read when viewed from an angle.
Watch with Data Memory
•
Allowing the battery to go dead, replacing the battery, or having your watch repaired
can cause all data in watch memory to be lost. Note that CASIO COMPUTER CO.,
LTD. assumes no responsibility for any damages or losses caused by data lost due
to malfunction or repair of your watch, replacement of the battery, etc. Be sure to
keep separate written copies of all important data.
E-58
•
A trained technician will inspect your watch for proper water resistance whenever
you have its battery replaced. Battery replacement requires the use of special tools.
Always request battery replacement from your original retailer or from an authorized
CASIO service center.
•
Some water-resistant watches come with fashionable leather bands. Avoid
swimming, washing, or any other activity that causes direct exposure of a leather
band to water.
•
The inside surface of the watch glass may fog when the watch is exposed to a
sudden drop in temperature. No problem is indicated if the fogging clears up
relatively quickly. Sudden and extreme temperature changes (such as coming into
an air conditioned room in the summer and standing close to an air conditioner
outlet, or leaving a heated room in the winter and allowing your watch to come into
contact with snow) can cause it to take longer for glass fogging to clear up. If glass
fogging does not clear up or if you notice moisture inside of the glass, immediately
stop using your watch and take it to your original retailer or to an authorized CASIO
service center.
•
Your water-resistant watch has been tested in accordance with International
Organization for Standardization regulations.
Temperature
•
Never leave your watch on the dashboard of a car, near a heater, or in any other
location that is subject to very high temperatures. Do not leave your watch where it
will be exposed to very low temperatures. Temperature extremes can cause your
watch to lose or gain time, to stop, or otherwise malfunction.
•
Leaving your watch in an area hotter than +60°C (140°F) for long periods can lead
to problems with its LCD. The LCD may become difficult to read at temperatures
lower than 0°C (32°F) and greater than +40°C (104°F).
Impact
•
Your watch is designed to withstand impact incurred during normal daily use and
during light activity such as playing catch, tennis, etc. Dropping your watch or
otherwise subjecting it to strong impact, however, can lead to malfunction. Note that
watches with shock-resistant designs (G-SHOCK, BABY-G, G-MS) can be worn
while operating a chain saw or engaging in other activities that generate strong
vibration, or while engaging in strenuous sports activities (motocross, etc.)
Storage
•
If you do not plan to use your watch for a long time, thoroughly wipe it free of all dirt,
sweat, and moisture, and store it in a cool, dry place.
Resin Components
•
Allowing your watch to remain in contact with other items or storing it together with
other items for long periods while it is wet can cause color on resin components to
transfer to the other items, or the color of the other items to transfer to the resin
components of your watch. Be sure to dry off your watch thoroughly before storing it
and make sure it is not in contact with other items.
•
Leaving your watch where it is exposed to direct sunlight (ultraviolet rays) for long
periods or failure to clean dirt from your watch for long periods can cause it to
become discolored.
•
Friction caused by certain conditions (strong external force, sustained rubbing,
impact, etc.) can cause discoloration of painted components.
•
If there are printed figures on the band, strong rubbing of the printed area can cause
discoloration.
•
Leaving a leather band where it is exposed to direct sunlight (ultraviolet rays) for
long periods or failure to clean dirt from a leather band for long periods can cause it
to become discolored.
CAUTION: Exposing a leather band to rubbing or dirt can cause color transfer and
discoloration.
Metal Components
•
Failure to clean dirt from metal components can lead to formation of rust, even if
components are stainless steel or plated. If metal components exposed to sweat or
water, wipe thoroughly with a soft, absorbent cloth and then place the watch in a
well-ventilated location to dry.
•
Use a soft toothbrush or similar tool to scrub the metal with a weak solution of water
and a mild neutral detergent, or with soapy water. Next, rinse with water to remove
all remaining detergent and then wipe dry with a soft absorbent cloth. When washing
metal components, wrap the watch case with kitchen plastic wrap so it does not
come into contact with the detergent or soap.
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any
damage or loss suffered by you or any third party arising through the use of your
watch or its malfunction.
E-51
E-53
E-55
E-57
E-59
Advertisement
