Advertisement
Spout Installation
(Refer to Figure 1 & 2)
Note: Some items have been
9/16"
pre-assembled at the factory to
ensure quality and fit. Some
11
disassembly may be required
during installation.
12
13
1.
Remove nut (12), washer (11), and tee
8
assembly (14) from spout mounting nipple
(13). *Note: once disassembled, the spout
14
base, escutcheon, and retaining pins may
be loose.
2.
Carefully put spout down on back, on a
clean surface.
3.
Remove escutcheon and retaining pins and
place a dab of silicone on tips of
retaining pins and put back into allotted
5
slots in spout base.
4.
Put escutcheon back on.
6
5.
Place spout through top hole of sink basin
or countertop, while holding top of spout.
6.
Place lift rod (3) through top of spout.
7.
Slide washer (11) onto spout with cut out
8
towards back of spout, allowing for lift rod
(3) to slip down.
8.
Thread nut (12) onto spout nipple and
secure to sink basin or countertop in
desired position.
9.
Screw tee (15) onto end of spout nipple
9
(14) using NSF listed joint
compound. *Note: tee (15) outlet ports
should be at 9 & 3 o'clock
10. Connect hot and cold hoses (10) to tee
assembly (14) and valve bodies (6 & 7 ).
FIGURE 1
9/16"
11
12
13
8
14
FIGURE 2
16
5
11
12
13
8
14
4
6
7
j a c l o i n d u s t r i e s | 129 Dermody Street Cranford, NJ 07016
p 908.653.4433 | 800.852.3906
7
8
3
17
COMPONENT PARTS
Aerator - CU-400-AER
Spout - CU-400-SPOUT-LL-**
Pop Up Rod Assembly - CU-400-R-*** / CU-400-K-***
Handle (2) - VARIES ON MODEL
11
Valve Escutcheon (2) - CU-400-ESC-***
Valve Body Hot - 11832-0
Valve Body Cold - 11833-0
Valve Body Nut (2)
Cock Nut - A438-0
Hose (2) - 5130-RGH
13
Washer - CU-400-WASHER-0
Brass Nut - CU-400-NUT-0
Brass Nipple - 0-CU-400-LL-NIPPLE
Brass Tee - CU-400-TEE-0
Spout Base - CU-400-SPTB-***
Spout Base Extension - CU-400-SPTB-EXT-***
10
Spout Plate - CU-400-PL-***
3
17
6
11
10
9
f 908.653.1717 | 800.852.4133
10
Valve Installation
(Refer to Figure 3, 4, & 5)
15
Spout Base
1.
Identify hot and cold valve. Hot has
Spout Base Extension
a red sticker and cold has a blue
17
Spout Plate
sticker.
2.
Install hot valve on left side of spout
as you are facing the sink.
A
3.
Remove handle (4), escutcheon (5),
top nut (12).
4.
Discard top nut.
5.
Lower under counter valve body nut
(8) to lowest position.
3
6.
Place valve body (6 or 7) through
9/16"
deck. Loosely affix escutcheon (5) on
5
2
11
valve all the way down.
12
1
4
7.
Place handle (4) on stem testing on/
13
6
7
8
off position. Tighten set screw on
14
handle.
*Note: out ports of both hot & cold
valve bodies should be facing spout.
12
5
8.
Bring escutucheon (5) up close to
6
but not touching handle (4).
*Note: use silicone under
8
escutcheon for water tight seal at
discretion of the installer.
10
14
9
Hose Installation
1.
Connect hot hose to hot valve outlet
and "T". Figure 3.
2.
Connect cold hose to cold valve
outlet and "T". Figure 3.
3.
Connect supply hoses or tubes
(not supplied) to base of hot and
Spout Base
cold valves. Figure 4.
Spout Base Extension
Spout Plate
Aerator Cleaning
ALWAYS REMOVE AERATOR AND
FLUSH THE FAUCET AFTER
INITIAL INSTALLATION
1.
Use aerator key supplied with faucet
Engage key in aerator. Figure 1.
2.
3
3.
Remove aerator by turning key
counterclockwise
2
4.
Turn on hot and cold water valves
1
flush lines
5.
Reinstall aerator by engaging key
and turning clockwise until tight
6.
Check for leaks, re-tighten if
necessary
12
13
Aerator
10
14
FIGURE 3
16
11
12
13
HOT
3
15
Spout Base
Spout Base Extension
17
Spout Plate
FIGURE 4
3
2
6
7
1
4
17
7
11
12
7
8
13
10
10
14
9
15
16
17
11
4
7
Key
FIGURE 1
COLD
14
16
11
12
Counter or
Basin
13
14
Valve Stem
10
6
7
10
8
9
FIGURE 5
12
13
14
A
6
7
10
8
9
REVISED 3.30.18
JACLO.COM
| PG 3
Advertisement
