XV-3080
FACTORY RESET
1. Press [UTILITY].
2. Press the [
] cursor key to show the "UTIL2" screen.
fig_fact1.eps
3. Select "FACTORY RESET" with the cursor keys, then press [ENTER],
and the display will show the following screen.
fig_fact2.eps
4. Press [ENTER].
•
If Internal Write Protect is ON, a warning will be issued and then the
display will show the following screen..
fig_fact3.eps
Press [DEC] to turn Internal Write Protect OFF, then press [ENTER],
and the display will return to showing the screen in step 3.
•
If Internal Write Protect is OFF, the display will show the following screen.
fig_fact4.eps
Factory reset is performed when [ENTER] is pressed.
8
ファクトリーリセットの方法
ファクトリーリセットの方法
ファクトリーリセットの方法
ファクトリーリセットの方法
1. [UTILITY] を押します。
2. カーソルキー [ ↓ ] を押して、 「UTIL2」の画面にします。
3. カーソルキーで「FACTORY RESET」を選び、[ENTER] を押すと、以下
のような画面になります。
4. [ENTER] を押します。
・ Internal Write Protect が ON の場合、警告の後、以下の画面が
表示されます。
[DEC] を押して Internal Write Protect を OFF にしてから [ENTER] を
押すと、3 の画面に戻ります。
・ Internal Write Protect が OFF の場合は、以下の画面になります。
[ENTER] を押すとファクトリーリセットが実行されます。
VERSION UP
The XV-3080 uses a flash memory for the program ROM. The version of
the program ROM can be upgraded by loading MIDI data into the XV-
3080. After upgrading the version, factory reset must be performed. If
important data is written in the user memory, save the data on a card
before upgrading the version.
Required Items:
•
XV-3080 Ver. Up Disk (2DD: Two disks) (#17048517)
•
Sequencer capable of regenerating SMF (Also possible using a syn-
thesizer with a sequencer)
•
MIDI cable
Version Up Procedure
1. Connect the MIDI cable from MIDI OUT of the external sequencer to MIDI
IN of the XV-3080.
2. Turn on the XV-3080 power while holding down [DEC] and [A] at the
same time, and the display will show the following MIDI update screen.
fig_update1.eps
3. Press [INC], and the display will show the following screen, waiting for the
reception of MIDI data.
fig_update2.eps
4. After confirming the display in step 3, regenerate all the "..mid" files in the
XV-3080 Ver. Up Disks 1 and 2 from the external sequencer (the order
does not matter). During the reception of MIDI data, the "MIDI message"
LED blinks and the message "Waiting" changes to the message "Receiv-
ing." When the data transfer of one file ends, the message "Waiting" will
appear on the display. Then regenerate the next file.
The use of a sequencer with a chain play function, such as the XP-80,
allows the version to be upgraded even more easily. Load and play the
".svc" file (chain file), and all the ".mid" files found on Disk 1 will be auto-
matically regenerated. When regenerating Disk 1 all ends, replace with
Disk 2 and play it again.
5. When the update ends normally, the display will show the following
screen and the [A] to [H] LED's will blink.
fig_update3.eps
6. After playing all the ".mid" files on the two Ver. Up Disks, turn on the XV-
3080 power again to ensure that the version has been upgraded correctly.
7. Lastly, perform factory reset.
This completes the version up.
NOTES:
Number of SMF's
•
One SMF is created for one block of flash memory.
•
Thirty-two SMF's, p00001.mid to p00032.mid, are created.
•
Some files may be omitted depending on the size of the program.
•
SMF is always created in p00032.mid because checksum data is
placed in it.
Ending the update
•
When p00032.mid has been received, it is judged that all the update
data has been received.
•
Any block, which has not been updated at this point of time, will be erased.
•
This is performed to properly control the checksum data in the external ROM.
•
Therefore, some blocks only cannot be updated.
JAN, 2000
バージョンアップの方法
バージョンアップの方法
バージョンアップの方法
バージョンアップの方法
XV-3080 は、プログラム ROM にフラッシュメモリを使用しています。
これは外部から MIDI データを送り込むことによりバージョンアップで
きます。なお、バージョンアップ後は必ずファクトリーリセットを行う
必要があります。ユーザーメモリに大切なデータが書込まれている場合
は、カードに保存してからバージョンアップ作業を行なって下さい。
◎用意するもの
◎用意するもの
◎用意するもの
◎用意するもの
・ XV-3080 Ver.Up Disk (2DD:2 枚組) (# 17048517)
・ SMF の再生できるシーケンサー (XP-80 等のシーケンサー付きシンセ
サイザーでも可)
・ MIDI ケーブル
◎バージョンアップの方法
◎バージョンアップの方法
◎バージョンアップの方法
◎バージョンアップの方法
1. MIDI ケーブルを外部シーケンサーの MIDI OUT から XV-3080 の MIDI
IN に接続します。
シーケンサーで SMF をチェインプレイできるように設定します。
2. [DEC] と [A] を同時に押しながら電源を入れると、以下のような MIDI
アップデート画面に入ります。
3. [INC] を押すと次の表示になり、MIDI データの受信待ち状態になります。
4. 3. の表示を確認した後、XV-3080 Ver.Up Disk 1,2 の中にある全ての
".mid" ファイルを外部シーケンサから再生します。 (順序は問いません)
MIDI データ受信中は [MIDI message] の LED が点滅し、 「Waiting」の
表示が「Recieving」に変わります。1 つのファイルのデータ転送が終
了すると、表示が「Waiting」になりますので、続けて次のファイルを
再生して下さい。
なお、XP-80 等のチェインプレイ機能を持つシーケンサーを用いると、
より簡単にバージョンアップができます。Disk 1 の中にある ".svc"
ファイル(チェインファイル)をロードし、PLAY すると、Disk 1 の中
の全ての ".mid" ファイルを自動的に再生します。
Disk 1 の再生が全て終了したら、Disk 2 に入れ替えて再び PLAY します。
5. アップデートが正常に終了すると次の表示になり、[A] -- [H] の LED
が点滅します。
6. 2 枚の Ver.Up Disk の全ての ".mid" ファイルをプレイし終わったら、
電源を立ち上げ直して、正しくバージョンアップされていることを確認
して下さい。
7. 最後にファクトリーリセットを行なって下さい。
以上でバージョンアップは終了です。
◎注意点
◎注意点
◎注意点
◎注意点
SMF の数について
SMF の数について
SMF の数について
SMF の数について
・ SMF は Flash Memory の 1 ブロックに対して、一つ作られます。
・ p00001.mid -- p00032.mid の 32 個の SMF が作られます。
・ プログラムのサイズによっては、 途中のファイルが抜ける事があります。
・ p00032.mid にはチェックサムデータが置かれますので必ず作られます。
アップデートの終了について
アップデートの終了について
アップデートの終了について
アップデートの終了について
・ p00032.mid を受信し終えると、全アップデートデータを受信したと
判断しています。
・ この時点でアップデートされなかったブロックは消去します。
・ これは外 ROM のチェックサムデータを正しく管理するためです。
・ 従って一部のブロックのみをアップデートすることはできません。