Advertisement
Changing the Supervisor Code
To change the supervisor code, follow the steps on page 8 to
enter programming mode.
The factory default supervisor code is 12345 (supervisor codes
must be 4 to 8 digits in length.)
There is a 10 second programming time limit between each step.
If KEDL times out or an error is made, programming will end
and you will need to enter programming mode again.
1. Place KEDL into programming mode (see page 8).
2. Press 2 and then press ENTER.
3. Type the current supervisor code and press ENTER.
4. Type the new supervisor code and press ENTER.
5. Retype the new supervisor code and press ENTER.
6. If successful, the green indicator light will illuminate for 1
second.
Continue programming or press 9 and then ENTER to exit
programming.
KEDL features a reset code which will restore the default supervisor
code and user code. KEDL was shipped with reset stickers; one attached
to the back of the KEDL and an extra sticker that should be saved in a
safe and secure location for future reference.
To restore the factory default supervisor and user code, type the Reset
Code assigned to the KEDL and press ENTER.
The KEDL features several modes of operation. These functions
can be changed using the following instructions with a valid
supervisor code.
Programming Single Use Mode / Standard Mode
Single Use Mode allows for a revolving user code so multiple
people may use the lock without having to reprogram the KEDL
each time.
Note: This mode cannot be used with Self Lock with SlamCAM.
Standard Mode KEDL operates with a fixed code. To change the
code, follow the Changing the User Code steps.
There is a 10 second programming time limit between each step.
If KEDL times out or an error is made, programming will end
and you will need to enter programming mode again.
1. Place KEDL into programming mode.
a. To turn Single Use Mode "ON": type 51 and then press
ENTER. OR
b. To return to Standard Mode: type 50 and then press
ENTER.
2. If successful, the green indicator light will illuminate for 1
second.
Note: Returning to Standard Mode will reset the factory user
default code (1234).
Continue programming or press 9 and then ENTER to exit
programming.
INSTRUCTIONS FOR
KEDL Lock
Call Free: 1.800.848.1633 • Fax Free: 1.800.447.2923
Web: GoHCL.com • Email: hcl@GoHCL.com
Programming Single Use Timeout ON / Single Use
Timeout OFF
Warning: Manual Lock - Single Use Timeout ON is a feature to
prevent users from occupying a shared use locker or cabinet for a
prolonged period of time. Turning this feature on will disable the
user code after a programmable amount of time. After this time
elapses, KEDL and can only be opened with the supervisor code.
To change the KEDL to Single Use Timeout ON or OFF, follow
the steps to enter programming mode.
There is a 10 second programming time limit between each step.
If KEDL times out or an error is made, programming will end
and you will need to enter programming mode again.
1. Place KEDL into programming mode (see page 8).
a. To set Timeout ON, type 2XX and then press ENTER.
(XX represents a time period from 04 - 12 in whole hours.)
OR
b. To turn Timeout OFF, type 20 and then press ENTER.
3. If successful, the green indicator light will illuminate for 1
second.
Continue programming or press 9 and then ENTER to exit
programming.
Reset User Code to Factory Default 1234
(Does not apply to Single Use Mode)
To reset the User Code to the factory default 1234 follow the
steps to enter programming mode.
There is a 10 second programming time limit between each step.
If KEDL times out or error is made, programming will end and
you will need to enter programming mode again.
1. Place KEDL into programming mode.
2. Type 8888 and then press the ENTER button.
3. If successful, the green indicator light will illuminate for 1
second.
Continue programming or press 9 and then ENTER to exit
programming.
© Health Care Logistics, Inc. 2014
Advertisement
