Advertisement
CompX RegulatoR is offered with Self Lock featuring SlamCAM. If your lock
is the Self Lock version, follow the directions below to unlock and lock the
KEDL is offered with Self Lock featuring SlamCAM. If your lock
RegulatoR:
is the Self Lock version, follow the directions below to unlock
and lock the KEDL:
To operate the Self Lock version of RegulatoR:
Type a valid code, press ENTER and rotate knob
clockwise 90°, hold knob until door or drawer is
open. Release knob, RegulatoR knob will return
to the locked position. Door or drawer can be
closed at any time.
CompX RegulatoR is offered in a Manual Lock version. If your lock is the
Manual Lock version follow the directions below to unlock and lock the
The KEDL is offered in a Manual Lock version. If your lock is the
RegulatoR.
Manual Lock version follow the directions below to unlock and
lock the KEDL.
RegulatoR, Keyless Locking 6
RegulatoR, Keyless Locking 7
INSTRUCTIONS FOR
To operate Manual Lock version of
RegulatoR:
To unlock, type a valid code, press
ENTER and rotate knob clockwise 90°.
To lock, rotate knob 90° counter
clockwise.
Call Free: 1.800.848.1633 • Fax Free: 1.800.447.2923
Web: GoHCL.com • Email: hcl@GoHCL.com
KEDL Lock
CompX RegulatoR features several modes of operation. These functions can be
KEDL Programming Mode
changed using the following instructions with a valid supervisor code.
Programming Single Use Mode / Standard Mode
To enter programming mode you must know the supervisor
code. The default supervisor code is 12345. Once in
Single Use Mode allows for a revolving user code so multiple people may use
programming mode, multiple changes can be made prior to
the lock without having to reprogram the RegulatoR each time.
exiting programming.
Note: This mode cannot be used with Self Lock with SlamCAM.
Standard Mode RegulatoR operates with a fixed code. To change the code,
There is a 10 second programming time limit between each step.
follow the Changing the User Code steps on page 9.
If KEDL times out or an error is made, programming will end
and you will need to enter programming mode again.
To change the RegulatoR to Single Use or Standard Mode, follow the steps on
page 8 to enter programming mode.
1. Lock must be in the locked position prior to entering
There is a 10 second programming time limit between each step. If RegulatoR
programming mode.
times out or an error is made, programming will end and you will need to enter
2. Type supervisor code and press ENTER.
programming mode again.
3. Turn knob clockwise 90° to the unlocked position and press
and hold ENTER for 3 seconds (yellow indicator light will
illuminate).
· If product is Self Lock with the SlamCAM feature you can now
let go of the knob.
4. With the yellow indicator light illuminated, programming can
begin.
Changing the User Code
To change the user code, follow the steps on page 8 to enter
Note: Returning to Standard Mode will reset the factory user default code
programming mode.
(1234).
Continue programming or press 9 and then ENTER to exit programming.
The factory default user code is 1234 (User codes must be 4 to 8
digits in length.)
There is a 10 second programming time limit between each step.
If KEDL times out or an error is made, programming will end
and you will need to enter programming mode again.
1. Place KEDL into programming mode (see page 8).
2. Press 1 and then press ENTER.
3. Type the current user code and press ENTER.
4. Type the new user code and press ENTER.
5. Retype the new user code and press ENTER.
6. If successful, the green indicator light will illuminate for 1
second.
Continue programming or press 9 and then ENTER to exit
programming.
1. Place RegulatoR into programming mode (see page 8).
To turn Single Use Mode "ON": type 51 and then press
a.
ENTER.
OR
b. To return to Standard Mode: type 50 and then press ENTER.
2. If successful, the green indicator light will illuminate for 1 second.
RegulatoR, Keyless Locking 11
© Health Care Logistics, Inc. 2014
Advertisement
