24/9 Powells Road, Brookvale NSW Australia 2100 hello@tecsunradios.com.au www.tecsunradios.com.au English DAB+/FM Digital Radio Receiver User Manual...
Safety Instructions: 1. Do not use this radio near water. 2. Clean with dry cloth. 3. Do not block any ventilation openings. 4. Do not use near heat objects. 5. Use accessories provided by manufacturer. 6. Do not allow this unit to be exposed to water, steam, sand or other environmental hazards.
Page 3
Specification: Model: DTR-762 Radio: Digital DAB+ & FM Dimension: 113x69x25mm Weight(Net): Approx. 120g (Included battery) DAB+ Frequency: Band III (174.0-239.0MHz) FM Frequency: 87.5-108MHz with RDS...
Page 4
Output Power: 32Ω 0.1W (headphone) Power Source: DC Adaptors (5V, 0.5A) Charging Time: Approx. 7 Hours Usage Time: Approx 10Hours (Speaker mode) / 18Hours (Headphone mode) Approvals: CE marked. RoHS marked. Compliant with the EMC and Low Voltage Directives (2004/108/EC and 2006/95/EC), ETSI EN300 401 compliant 24/9 Powells Road, Brookvale NSW Australia 2100 hello@tecsunradios.com.au...
Page 5
24/9 Powells Road, Brookvale NSW Australia 2100 hello@tecsunradios.com.au...
Page 7
Charging the radio: The DTR-762 features a 3.7V, 2000mAh rechargeable Lithium battery. The DTR-762 is supplied with a USB power cable for charging. Before first time to operate, please fully charge the battery. 1. Plug the USB power cable into the...
Page 8
Speaker: The DTR-762 features a high-quality 4 Ω 2W speaker. Headphones: The DTR-762 features a pair of high-quality earpieces. The 3.5mm jack is located on the left-hand side of the radio, it is provided for use with stereo headphones or earpieces.
Page 9
Operating your radio: 1. Make sure the battery is charged. 2. Press and hold the button to turn on the radio. 3. The display will show ‘CORUS’ logo and enter DAB mode ( or FM mode if you selected FM before turning off). 4.
Search and select channels : DAB+ mode 1. Make sure the radio is in DAB+ mode. 2. Press once the “SCAN/ST” button to activate the quick scan function. 3. Press and hold the “SCAN/ST” button to activate the full scan of all available radio channels and all the scanned channels will be saved in a channel list.
Page 11
Presets: DAB+ mode 1. Press and hold the “MEM/PRE” button, then “Null Memory 01” will show on the display if the position is empty whereas it will show the name of the channel if it is already occupied. Press the “CH+” or “CH-” button to select the position to save, then press “MEM/PRE”...
Page 12
3. Max. 99 preset channels for DAB+ radio mode. Service Information: DAB+ mode The Service Information display - Technical information on the current status of the station being broadcast While listening to DAB+, the display will show the followings if applicable 1.
Page 13
Search and select channels : FM mode 1. Press and hold the button to turn on the radio. 2. Press once the button to switch to FM Mode. 3. Press and hold “TUNE+” and “TUNE-“ to search the nearest channel automatically. Changing audio mode: 1.
Page 14
Manual tuning: FM mode 1. Press once the “TUNE+” or TUNE-” button to search the channel manually. Service Information: FM mode While listening to FM radio, the display will show the followings if applicable 1. Program type 2. Frequency 3. Channel Name 4.
Page 15
Presets: FM mode 1. Press and hold the “MEM/PRE” button, then “Null Memory 01” will show on the display, press the “CH +” or “CH -” button to select the position to save, then press “MEM/PRE” button again to confirm. 2.
Radio Antenna: 1. For DAB+ and FM reception there is a built-in telescopic antenna at the rear of the unit. 2. Extend the antenna and move it around to obtain the best reception. 3. If the reception is still unsatisfactory, pull the antenna as long as possible.
2. Press the “SLP/DISP” button until the sleep time in red disappeared to cancel the sleep function. 3. The radio will be powered off when the timer reduces to 0 of sleep time. Select Language: 1. Set the display language. 2.
Page 18
Backlighting: 1. Set how long backlighting remains 2. Press and hold the “SLP/DISP” button, then “BACKLIGHT” menu will show on the display, press the “CH+” or “CH-” button to select backlight timeout period. 3. Press once the “SLP/DISP” button to save.
Factory Reset: 1. Press and hold the “SLP/DISP” button and press the “SCAN/ST” button at the same time to activate the factory reset function. 2. Factory reset function will clear all the preset radio channels. Power Off and Maintenance: 1. Please shut down the power when not in use.