Sokkia SX series Quick Manual

SX_Quick_E.fm 1 ページ ２０１２年５月１４日 月曜日 午後２時３９分

Nomenclature

1
2
19
18
17
33
3
32
16
4
31
30
5
6
7
8
9
15
10
14
11
13
12
29
1 Wireless antenna 7 Optical plummet reticle cover
2 Handle 8 Optical plummet eyepiece
9 Keyboard
3 Beam detector for Remote
Controler 10 Circular level
11 Circular level adjusting screws
4 Instrument height mark
5 External interface hatch 12 Serial / External power source
6 Optical plummet focussing ring connector

Display Functions

Observation mode screen
Status bar
Distance
Vertical angle
Horizontal angle
Soft key
Page number
Press and hold the icons [2] to [8],
(Next page exists.)
and the selection screens appear.
[7] Input mode icon
C Inputting letters / figures
[8] Input panel icon

Basic Key Operation

Power ON
Press the power key on the side of the instrument.
Power OFF
Press and hold (about 1sec) the power key on the side of the
instrument.
Lighting up the reticle/keys and selecting screen
backlight brightness
Switches the reticle illumination and key light On/Off
(When Key light is On, backlight brigthtness goes down)
Switching to star key mode
{ } Switches to star key mode / basic mode
Switching to program mode
{PRG} Switches to program mode / basic mode
Switching target type
Switches between target types
Prism/360°Prism/Sheet/N-prism(reflectorless)
• Changes can also be made by tapping the icon on status bar or in star
key mode.
Switching the page
{FUNC} Toggle between Observation mode screen pages
SURVEYING INSTRUMENTS
SX series
Quick Manual
21305 90080
20
13 Levelling base locking screw
14 Luminance sensor
15 Display unit
16 Objective lens (Includes
"Laser-pointer function")
17 Guide light
21
18 Handle locking screw
22
19 Sighting collimator
23
20 Tubular compass slot
24 21 Vertical Jog
22 Power key
23 Horizontal Jog
24 Trigger key
25
25 Battery cover
26
26 Stylus (pen)
27
27 Levelling foot screw
28 Base plate
28
29 Tribrach clamp
30 Telescope eyepiece
31 Telescope eyepiece screw
32 Telescope knob
33 Telescope focussing ring
[1] Battery icon [2] Target type icon
: Level 3 Full power
[1] : Level 2 Plenty of power remains.
[2]
[3]
: Level 1 Half or less power remains.
[4]
[5] : Level 0 Little power remains.
(Flashes red)
[6]
[7]
[4] Laser-pointer
[8] [5] Tilt angle compensation icon
/guide light icon
[9] PPM setting icon
Disk usage icon
: Less than 20%
[10] Config mode icon
: 20 to 50%
Switch to Config mode
: More than 50%
Switching the Laser-pointer/Guide light ON/OFF
(Press and hold )
• Changes can also be made by tapping the icon on status bar or in star key
mode.
Inputting letters/figures.
α
{ }
{SHIFT} + {1} to {9}
{SHIFT}
(Press and hold)
α
{SHIFT} + { }
{0} to {9}
{.}
{±}
{ESC}
{TAB}

Mode Structure

Power key [ON]
Tilt screen
[ESC]
Instrument name
Serial number
Version information
Operation panel
{ }
ESC
Display unit
{ }
TAB
{ }
SHIFT
{ } Switching the page
FUNC
Luminance sensor / Microphone
[3] Motor icon
[6] Communication status with
external devices icon
Blue
Green
Touch panel icon
To turn the laser-pointer/guide light ON/OFF, press
and hold until a beep sounds.
Switch between numerals and alphabetic characters
In alphabetic characters mode, switch between
lowercase characters and upper case characters
each time
In alphabetic characters mode, switch between
lowercase characters and upper case characters
<Input Panel> is displayed
Input numeral or symbol printed above the key
(during numeric input mode)
Input alphabetic character in the order they are listed
(in alphabetic input mode)
Input a decimal point (during numeric input mode)
Input a plus or minus sign (during numeric input
mode)
Cancel the input data.
Shift to the next item
Observation mode
[OBSERVE]
Top menu Menu mode
[ESC]
[MENU]
[VERSION]
Config mode
[CONFIG]
Star key mode
Press the star key [
key mode, it is possible to change
the setting item that is frequently
{ }
B.S.
{ }Star key mode
used during measurement.
[1]
[5]
{ }Illumination
[9]
[1] Battery icon
{ }
ENT
[2] Target type icon
[3] Motor icon
[4] Laser-pointer/guide light icon
{ } Switching input mode
[5] Tilt angle compensation icon
{ }
[6] Communication status with
external devices icon
[7] Input mode icon
{ }
Switching target type
[8] Input panel icon
{ }
PRG Program mode
[9] PPM setting icon
[10]Config mode icon
Disk usage icon
Input screen
Measuring screen
Laser is emitted
Switch to <Motor configuration>
Config mode Motor configuration
.
{B.S.} Delete a character on the left.
Input a blank space (increments by 1 when setting the
{S.P.}
date and time)
{ }/{ } Right and left cursor/Select other option.
{ }/{ } Up and down cursor
{ENT} Select/accept input word/value.
Selecting options
Move the cursor/selection item up/down
{ }/{ }
Move the cursor/selection item left/right or select
{ }/{ }
other option
Shift to the next item
{TAB}
{S.P.} Display other options
Select/accept the option
{ENT}
Selecting tabs
{ }/{ } Move tab/cursor in tab up/down
{ }/{ } Display next tab at left/right
Others
{ESC} Return to the previous screen
]. In the star
[2] [3] [4]
[8]
[6] [7] [10]
Touch panel icon