Download Print this page

Pioneer AS-WL300 Getting Started

150mbps wireless lan converter.
Hide thumbs
   

Advertisement

150Mbps WIRELESS LAN CONVERTER
AS-WL300
AS-WL300
Getting Started
Getting Started
Getting Started
Version: AS-WL300_QIG-A_V1
● This guide explains the usage of and necessary settings for this unit. Please
follow the procedure to complete the settings. Do not lose this guide.
● Refer to the USER'S MANUAL found on the supplied CD-ROM or on the
Web for details of other settings and uses not explained in this guide.
Refer to "The USER'S MANUAL" on the reverse for more details.
● Some Pioneer products that connect to this product will need to be
configured. Refer to their respective USER'S MANUAL for more details.
● For technical enquiries regarding this product, refer to "Please Read First"
for Support Centre details.
Features
Connect the following Pioneer AV devices using a
Wireless LAN.
AV RECEIVER
Blu-ray Disc player
Wireless LAN Converter
Wireless LAN Converter
Wireless LAN Converter
(this unit)
(this unit)
(this unit)
Connect supported AV devices
e a s i l y o v e r a W i r e l e s s L A N
Internet connection
using this unit.
Wireless LAN router
(base)
ADSL modem
ONU (Optical Network Unit)
Wired router, etc.
Setup Procedure
STEP 1
Check the Base
* Check that the base has no problem connecting to
the Internet.
STEP 2
Connect the Unit
● If the base has a WPS button
→Follow the instructions in "Step 2 Connect the Unit
(WPS)" to connect the unit to the base.
● If the base does not have a WPS button
→Follow the instructions in "Step 2 Connect the Unit
(Manual)" to connect the unit to the base.
* If you have problems using the "WPS Button,"
use the "Manual" procedure.
STEP 3
Step 3 Connect AV Devices
Preparation
Prepare the following.
□ Wireless LAN Converter (this unit)
□ LAN/USB feeder cable (included) * This cable is a combination of a
LAN cable and a USB feeder cable
that supplies power to the unit
without using an AC adapter.
Use the supplied cable only.
□ Getting Started (this guide)
□ Supported AV device, computer (not included)
□ Internet connection (not included)
Part Names
Front
Back
Side
DC 5 V
ETHERNET
WPS
④ ⑤
① POWER indicator
④ POWER connector
⑦ RESET button
② WPS indicator
⑤ ETHERNET port
③ WIRELESS indicator
⑥ WPS button
Before Configuring the Unit
● If you do not have an Internet connection, subscribe before
configuring the unit.
● Do not connect the LAN/USB feeder cable to a USB hub.
STEP 1
Check the Base
Check that the Wireless LAN router (base) has no
1
problem connecting to the Internet.
Internet
connectivity
Internet connection
Modem
Wireless LAN router
Computer
(base)
This procedure requires a separate Wireless LAN router (base).
If you do not have a base, please prepare one.
Check that the base has a WPS function. Refer to the
2
Wireless LAN router user's manual for details.
WPS is a function that configures the base connection and security
using a button.
Notes
* Some bases have WPS written on them.
If the base has a WPS button
Continue to "Step 2 (WPS)" and " Step 3" .
If the base does not have a WPS button
Continue to "Step 2 (Manual)" and " Step 3" .
Please connect using either method.
Please connect using either method.
STEP 2
Connect the Unit (WPS)
● This procedure explains how to connect the unit using the WPS
function. If the base does not have a WPS function, refer to the
"Manual" procedure below.
● Do not connect the LAN cable to the unit until instructed.
● When using multiple units of this product, the IP address of this unit
needs to be changed. Refer to "Troubleshooting" on the reverse.
1. Switch on the unit
Switch off the AV device.
1
OFF
AV RECEIVER
Blu-ray Disc player
Connect the POWER connector on the unit to the USB port on the
2
AV device using the USB end of the supplied feeder cable.
DC 5 V
ETHERNET
WPS
A USB port is the
AV RECEIVER
horizontally
* The location of the USB
(or vertically) long port
port and its name may
(as shown above).
vary depending on the
*
On some devices, it is
device. If you cannot
Blu-ray Disc player
labelled [DC OUTPUT
locate a USB port, refer
for WIRELESS LAN].
to the device' s user's
manual for help.
Switch on the AV device.
3
ON
AV RECEIVER
Blu-ray Disc player
Check that the "
(POWER)" , "
(WPS)" and "
(WIRELESS)"
4
indicators on the unit are lit.
* Once the indicators light up, wait
2 minutes before proceeding.
Lit
2. Connect the Unit
Press the "WPS" button on the base. Refer to the base user's manual
1
for more details on the WPS button.
Press and hold the "WPS" button on the back of the unit until the
2
WPS indicator on the front flashes. (over 2 seconds).
Press and hold for over 2 seconds
The WPS indicator (centre) will flash
DC 5 V
ETHERNET
WPS
Check that the WPS indicator on the unit changes from a flashing light
3
to a steadily lit light.
* If the WPS indicator stops flashing and is steadily lit,
the unit is connected to the Wireless LAN.
 (The unit is not connected if the WPS indicator is
flashing.)
* If the WPS indicator does not flash, press the "WPS"
button again.
* If the WPS indicator stops flashing and turns off,
press the "WPS" button again.
Once the WPS indicator lights, wait 2 minutes before proceeding to
Disconnect the USB feeder cable end of the supplied cable that
4
is connected to the unit.
DC 5 V
ETHERNET
WPS
AV RECEIVER
Blu-ray Disc player
Connection to the base is now complete. Continue to Step 3.
STEP 2
Connect the Unit (Manual)
● Use this procedure to manually connect the unit, especially if connecting
the unit using the "WPS" procedure, above, does not work.
● If the computer on which you will configure the unit is connected to the
Wireless LAN cable disconnect it.
● When using multiple units of this product, the IP address of this unit
needs to be changed. Refer to "Troubleshooting" on the reverse.
1. Search for a Network Connection
Before connecting or configuring this unit, you must know the Wireless LAN
settings for your base. Write the settings in the table below.
* Refer to the base user's manual for details on the Wireless LAN settings.
When using WEP security settings
Name
Wireless LAN Settings
(1)
SSID (Network name)
OFF
(2)
Authentication
□ OPEN 
(3)
Authentication key method
□ Hexadecimal
(4)
Default key
□ Key 1
□ Key 2
(5)
Encryption key
* 1: 16-digit number (0-9, A-F) * 2: ASCII (1-byte letters and numbers, including upper and lowercase letters)
When using WPA/WPA2 security settings
Name
Wireless LAN Settings
(1)
SSID (Network name)
(2)
Authentication
□ WPA-PSK
(3)
Authentication key
□ Hexadecimal
(4)
Encryption
□ TKIP
(5)
Encryption key
* 1: 16-digit number (0-9, A-F) * 2: ASCII (1-byte letters and numbers, including upper and lowercase letters)
This unit cannot connect to a base with a SSID (Network name) that includes a semicolon (;).
Refer to the base user's manual for details on changing the SSID.
2. Connect to the Computer
Switch off the computer.
1
Connect the ETHERNET port on the unit to the computer LAN port
2
on the computer using the LAN end of the supplied feeder cable.
* The location of the LAN port and its name may vary
depending on the computer. If you cannot locate a LAN
port, refer to the computer user's manual for help.
DC 5 V
ETHERNET
WPS
ON
The LAN port is the large port that is slightly
larger than a telephone modular jack.
LAN
* Some bases have LAN written on them.
Connect the POWER connector on the unit to the USB port on
3
the computer using the USB end of the supplied feeder cable.
* The location of the USB port and its name may
vary depending on the device. If you cannot
locate a USB port, refer to the device' s user' s
DC 5 V
ETHERNET
WPS
manual for help.
A USB port is the horizontally (or vertically) long
port (as shown above).
USB
* On some computers, it is labelled "USB" or
marked by a "
Switch on the computer.
4
Check that the "
(POWER)" , "
(WPS)" and "
5
indicators on the unit are lit.
* Once the indicators light up, wait
2 minutes before proceeding.
3. Configure the Unit
Launch the Web browser.
1
Enter "cv.setup" in the Address
2
bar and press <Enter>.
4
.
If you cannot display the Web Configuration window by entering "cv.setup" , enter
"192.168.1.249" and proceed to
. If the window still does not open, refer to
3
"Troubleshooting" on the reverse.
① Enter "admin" as the user name
3
and "password" the password.
② Click [OK].
If you cannot log in to the Web
Configuration window, check that you
have entered the settings, correctly.
Continued over the page
□ SHARED
*1
*2
□ ASCII
□ Key 3
□ Key 4
□ WPA2-PSK
*1
*2
□ ASCII
□ AES
OFF
" .
ON
(WIRELESS)"
Lit
1
2

Advertisement

   Related Manuals for Pioneer AS-WL300

   Summary of Contents for Pioneer AS-WL300

  • Page 1

    □ Supported AV device, computer (not included) Refer to “The USER'S MANUAL” on the reverse for more details. Name Wireless LAN Settings ● Some Pioneer products that connect to this product will need to be (1) SSID (Network name) □ Internet connection (not included) (2)...

  • Page 2

    CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY properly. Refer to the device user's manual for more details. □ AS-WL300 (this unit)   □ LAN/USB feeder cable OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Comments to this Manuals

Symbols: 0
Latest comments: