Related Manuals for Siskiyou MC1000e-R
Summary of Contents for Siskiyou MC1000e-R
- Page 1 An Oregon Corporation Motion Controller User’s Manual MC1000e-R / T © 2013 by Siskiyou Corporation...
-
Page 2: Table Of Contents
Copyright © 2013 Siskiyou Corporation. All rights reserved. No part of this catalog may be reproduced, copied or transmitted in any form or by any means electronic or mechanical, including photocopying, recording, taping, or by an information storage and retrieval system, in English or in other languages, without written permission from the publisher. -
Page 3: Section 1.0 - Introduction
MC1000e-R / T User’s Manual 1.0 Introduction This manual describes the operation of Siskiyou’s Model MC1000e-R / T micromanipulator motion controller. 1.1 Inspection Siskiyou products are shipped in sturdy, cushioned boxes. Please inspect the instrument immediately and notify the carrier if damage is obvious. -
Page 4: Section 3.0 - Installation
WHILE POWER IS ON. FAILURE TO DO SO CAN RESULT IN A SHORT CIRCUIT AND PERMANENT DAMAGE TO THE SYSTEM. To install the MC1000e-R/T, please refer to Figure 1: Interface or the supplied set up instructions. Supplied with the MC1000e-R/T are two ¼-20 screws that can be used in securing both the controller and the junction box to the work station. -
Page 5: Section 4.0 - Interface
Power Switch: The power switch turns on the junction box and the control- ler. This is required to be on in order to use the MC1000e-R/T. Turning off the power switch will cease all operations with manipulators remaining in place. -
Page 6: Section 5.0 - Operatiion
5.0 Operation When the MC1000e-R/T has been correctly installed, the user can begin use of the system. The operation may be bench tested prior to installing the unit to an experiment. -
Page 7: Section 6.0 - Troubleshooting
There are no user servicable parts inside the controller or junction box. telephone or email communication, an RA num- In the event of the need for service, call Siskiyou Corporation and have the ber will be provided to return the unit to Siskiyou information as shown on the Service Form (page 7) ready to discuss with a Corporation. -
Page 8: Related Products
MC1000e-R / T User’s Manual Related Products Switching Box ABCD switching box allows control of one to four 4-axis micromanipula- tors by one controller (MC2000 excluded). The basis of the design is simple and requires only an extra controller junction box for each added microma- nipulator or motor drive group (up to four per group). -
Page 9: Service Form Sf9
Service Form Return a copy of this form along with the product to Siskiyou Corporation Company _______________________________________ Return Authorization No. _____________________________ Note: Call the toll free number prior to returning the item. Address _______________________________________ City, St Zip _______________________________________ Date _____________________________________________... - Page 10 MC1000e-R / T User’s Manual CE Certificate EU Declaration of Conformity In accordance with EN 45014: 1998 Manufacturer: Siskiyou Corporation Address: 110 SW Booth Street Grants Pass, OR 97526-2410 Declare that: Equipment Motion Controller Model Name/Number MC1000e Series Serial Number N/A...
-
Page 11: Contact Information
MC1000e-R / T User’s Manual Contact Information Washington INTERSTATE 5 Portland Salem Mailing Address Siskiyou Corporation Eugene OREGON 110 S.W. Booth Street Grants Pass, OR 97526-2410 Grants Pass California Sales and Service Oregon-7.eps sales@siskiyou.com service@siskiyou.com telephone (toll free): 1-877-313-6418 Technical Assistance tech@siskiyou.com... - Page 12 Siskiyou Corporation 110 SW Booth Street Grants Pass, OR 97526-2410 Telephone 541-479-8697 Toll-Free 877-313-6418 Facsimile 541-479-3314 Website www.siskiyou.com...
Need help?
Do you have a question about the MC1000e-R and is the answer not in the manual?
Questions and answers