Subscribe to Our Youtube Channel
Related Manuals for McConnel EZI-EDGER
Summary of Contents for McConnel EZI-EDGER
- Page 1 Publication 200 EZI-EDGER May 1994 Part No. 1270850 TRACTOR MOUNTED EDGING ATTACHMENT Operator & Parts Manual...
- Page 2 VERIFICATION OF WARRANTY REGISTRATION DEALER WARRANTY INFORMATION & REGISTRATION VERIFICATION It is imperative that the selling dealer registers this machine with McConnel Limited before delivery to the end user – failure to do so may affect the validity of the machine warranty.
-
Page 4: Warranty Policy
1500 hours. Engine warranty will be specific to the Manufacturer of that unit. 1.02. All spare parts supplied by McConnel Ltd and purchased by the end user are warranted to be free from defects in material and workmanship from the date of sale to the original purchaser for a period of 6 months. -
Page 5: Limitation Of Liability
2.02. Any fault must be reported to an authorised McConnel Ltd dealer as soon as it occurs. Continued use of a machine, after a fault has occurred, can result in further component failure for which McConnel Ltd cannot be held liable. - Page 6 MISCELLANEOUS 4.01. McConnel Ltd may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term. 4.02. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein.
-
Page 7: Declaration Of Conformity
DECLARATION OF CONFORMITY Conforming to EU Machinery Directive 2006/42/EC McCONNEL LIMITED, Temeside Works, Ludlow, Shropshire SY8 1JL, UK Hereby declare that: The Product; Tractor Mounted Kerb Maintenance Attachment Product Code; EZIE Serial No. & Date ………………………………… Type ………………………… Manufactured in; United Kingdom Complies with the required provisions of the Machinery Directive 2006/42/EC The machinery directive is supported by the following harmonized standards;... - Page 8 Temeside Works Ludlow Shropshire England Telephone: +44 (0)1584 873131 www.mcconnel.com Operating, servicing and maintaining this equipment can expose you to chemicals including gasoline, diesel fuel, lubricants, petroleum products, engine exhaust, carbon monoxide, and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm.
- Page 9 GENERAL INFORMATION Always read this manual before fitting or operating the machine – whenever doubt exists contact your dealer or the McConnel Service Department for advice and assistance. Use only McConnel Genuine Service Parts on McConnel Equipment and Machines DEFINITIONS –...
- Page 10 15” (375mm) ground clearance beneath the bar. Do not tighten the nuts fully at this stage. Remove the mounting and transport pins from the Ezi-Edger. Slide the Ezi-Edger onto the mounting bar. It may be necessary to connect up the hydraulics at this point (see later) to adjust the ram and facilitate fitting.
-
Page 11: Operation
Secure hose ends clear of the ground and cover ends with dust caps. Removal from Tractor Ensure disc is in the raised position. • Disconnect hoses. • Slacken the mounting bar clamps. • Withdraw mounting bar together with Ezi-Edger. The mounting bracket may be left permanently on the tractor. -
Page 12: Parts Section
PARTS SECTION For best performance … USE ONLY GENUINE McCONNEL SERVICE PARTS To be assured of the latest design improvements purchase your ‘Genuine Replacements’ from the ‘Original Equipment Manufacturer’ McCON NEL LIMITED Through your local Dealer or Stockist Always quote:... -
Page 13: Body Assembly
BODY ASSEMBLY McCON NEL EZI-EDGER... - Page 14 BODY ASSEMBLY McCON NEL EZI-EDGER...
-
Page 15: Hub Assembly
HUB ASSEMBLY McCON NEL EZI-EDGER... - Page 16 HUB ASSEMBLY McCON NEL EZI-EDGER...
-
Page 17: Carrier Assembly
CARRIER ASSEMBLY McCON NEL EZI-EDGER... - Page 18 HYDRAULIC RAM ASSEMBLY McCON NEL EZI-EDGER...
- Page 20 McConnel Limited, Temeside Works, Ludlow, Shropshire SY8 1JL. England. Telephone: 01584 873131. Facsimile: 01584 876463. www.mcconnel.com...
Need help?
Do you have a question about the EZI-EDGER and is the answer not in the manual?
Questions and answers