Related Manuals for Foxfury Lighting Solutions COMMAND SERIES
Summary of Contents for Foxfury Lighting Solutions COMMAND SERIES
- Page 1 COMMAND SERIES 410-L06 | 410-T09 | 420-L06 | 420-T06 | 420-T09 | 420-T15 420-L06R | 420-T09R PRODUCT MANUAL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INTRODUCTION Command Reference Guide Physical Characteristics & Warnings BATTERY Battery Installation Reassembling the Battery Pack COMMAND RECHARGEABLE Charging the Battery Pack Battery Life OPERATION Operational Modes Battery Life INSTALLING STRAPS Elastic Strap Silicone Strap WARRANTY 10–11 CONTACT FOXFURY... -
Page 3: Command Reference Guide
COMMAND REFERENCE GUIDE COMMAND & COMMAND + TIL T LIGHT HEAD FOAM PADDING TIL T PLATE POWER/MODE SWITCH BUCKLE SLOT (3 EACH) LENS COMMAND & COMMAND + LO•PRO LIGHT HEAD POWER/MODE SWITCH TIL T PLATE BUCKLE SLOT (2 EACH) LENS COMMAND &... -
Page 4: Physical Characteristics & Warnings
PHYSICAL CHARACTERISTICS Please read below before using your Command headlamp as it relays beneficial operating and safety information. DIMENSIONS NAME WEIGHT (L x W x H) Command LoPro 5.3 x 0.7 1.0 in 410-L06 (White) (135 x 18 x 25 mm) Command Tilt 4.8 x 1.0 x 1.0 in 410-T09... -
Page 5: Battery
BATTERY The Command Series requires four (4) AA batteries. Acceptable battery types include: Alkaline or rechargeable Alkaline, rechargeable NiMH or LiFeS (all are 1.2 to 1.6 volts each). Do not leave batteries in the Battery Pack for periods longer than three (3) months without use. -
Page 6: Command Rechargeable
COMMAND RECHARGEABLE CHARGING THE BATTERY PACK (FOR P/N 420-L06R, -T09R ONL Y) Begin by plugging the AC-DC Adaptor into an outlet. The Charge Indicator will then turn solid green. Plug the Barrel Connector into the Battery Pack. Once plugged in, the Charge Indicator on the AC-DC Adaptor, will turn solid red to indicate that it is charging. -
Page 7: Operational Modes
OPERATIONAL MODES COMMAND TILT & COMMAND LO•PRO: ON/LOW mode: Press the Power/Mode switch once. The center 2 LEDs will turn on. MEDIUM mode: From LOW mode, press the Power/Mode Switch once. The center 6 LEDs will turn on. HIGH mode: From MEDIUM mode, press the Power/Mode Switch once. All 10 LEDs will turn on. -
Page 8: Elastic Strap
INSTALLING THE ELASTIC STRAP | 5 MINS (APPROX) (WATCH THE VIDEO: FOXFURY .COM/VIDEOS) FoxFury logo on strap should face inward for STEP 1 Place the headlamp on a flat surface. Position the Light Head so the Power/ Mode Switch is on the left and the LEDs face forward. NOTE: Make sure the FoxFury logo on the Battery Pack is correctly oriented before beginning. -
Page 9: Silicone Strap
INSTALLING THE SILICONE STRAP | 5 MINS (APPROX) (WATCH THE VIDEO: FOXFURY .COM/VIDEOS) Place the headlamp on a flat surface. Position the Light Head so the Power/ Mode Switch is on the left and the LEDs face forward. NOTE: Make sure the FoxFury logo on the Battery Pack is correctly oriented before beginning. -
Page 10: Warranty
WARRANTY AND OTHER INFORMATION PRODUCT DURABILITY Do not stare into LEDs for long periods of time or from a close range (less than 2 ft). FoxFury , LLC is not responsible IPX7 for any injury or damage caused during the use of this product. Meets NFPA 1971-2007 Fire Resistant Requirements: 500°F Usage of this product must be... -
Page 11: Contact Foxfury
other than FoxFury) prior to your Products are assembled in either purchase, you are not the Original FoxFury’s controlled plant in Asia or Purchaser and the product that you the USA, under strict quality control. purchased is not covered by this warranty . - Page 12 FOXFURY .COM 10/2018...
Need help?
Do you have a question about the COMMAND SERIES and is the answer not in the manual?
Questions and answers