Beachcomber 500 Series Owner's Manual page 11

Time Of day and filTer CyCles seTTinG
On all systems, the 2 speed filter pump or HushPump™
and ozone generator will run during filtration. There are two
filter cycles per day. The start/end times of each cycle are
programmable. Programming filter times on HushPump™
equipped hot tubs are used to tell the system how many hours a
day to turn the heater on when in Economy mode.
To Program:
1. Press then .
2. Use the and buttons to adjust the time of
day in hours, press the again to adjust the time in
minutes. Use the and
minutes. Press to enter new time.
prOGram filTer 1 (F1)
3. You will see ,
Time
appears on the display. Press
to choose the filter start time hour. Enter the hour by
pressing .
4. Press or to choose the filter start time
minutes. Each press will change the start time by 5
minutes. Enter the minutes by pressing
prOGram
5. Press to see the
end Time
. Adjust the time as done above.
prOGram
6. Press to see the
sTarT Time
. Proceed as above.
prOGram
7. Press to see
end Time
. Adjust the time as done above.
8. The time that now appears allows you to turn your hot tub
light on automatically. Adjust time as done above.
9. Program the time you want your light to turn off.
10. Press will enter the new filter cycle times into the
system and display the current water temperature.
panel inVersiOn
Press the or button, followed by the
button to change the numbers in the display to read upside
down. Press the same sequence to set back.
lOCKinG THe panel
1
Press , then within 3 seconds. When locked, the
pl
indicator light will light up. All buttons are frozen except the
button. To unlock the panel, press ,
lOCKinG THe seT TemperaTure
Press or then ,
Tl
seconds to activate the lock. The indicator light will light up
when temperature is locked. To unlock the set temperature, press
or then
1
, and .
TAMPERING WITH OR MODIFYING
WarninG
THIS EQUIPMENT MAY VOID YOUR
GUARANTEE.
periOdiC reminder messaGes
(press the
rPH:
rCL:
rt9:
rdr:
rCO:
buttons to adjust the
rCH:
sTarT
,
To suppress reminders, refer to the user edit menu on
or
page 12.
diaGnOsTiC display messaGes
OHH
ICE:
.
SnA:
filTer 1(F1)
, ,
Snb:
SnS:
filTer 2(F2)
, ,
HFL:
LF:
filTer 2(F2)
, ,
dr:
drY:
Pr:
- - :
---:
please refer TO TrOuBle sHOOTinG Guide
sTarTinG On paGe 25 fOr a COmpleTe
eXplanaTiOn Of diaGnOsTiC messaGes.
or
WarninG
1
then .
DO NOT ATTEMPT SERVICE OF THIS CONTRO�.
CONTACT YOUR RETAI� STORE OR SERVICE PROVIDER
1 FOR ASSISTANCE. FO��OW A�� OWNER'S GUIDE POWER
and within 3
CONNECTION INSTRUCTIONS. INSTA��ATION MUST
BE PERFORMED BY A �ICENSED E�ECTRICIAN AND
A�� GROUNDING CONNECTIONS MUST BE PROPER�Y
INSTA��ED.
WarninG
CONTRO� PAD. ENSURE COMFORT BY A�SO CHECKING
WATER WITH A THERMOMETER.
button to reset a displayed reminder message)
Test and adjust pH chemical levels as per Beachcomber
instructions. Reminder is every 7 days.
Remove, clean, and reinstall Microfilter as per
Beachcomber instructions. Reminder is every 30 days.
Test & reset GFCI as per Beachcomber instructions.
Reminder is every 30 days.
Drain and refill hot tub as per Beachcomber instructions.
Reminder is every 90 days.
Clean and condition Heatshield as per Beachcomber
instructions. Reminder is every 180 days.
Install new Microfilter. Reminder is every 365 days.
OHS:
or Overheat-DO NOT ENTER HOT TUB
Potential Freeze
Hot tub is shut down
Hot tub is shut down
Sensor out of balance
Could indicate flow problem
Persistent low flow problems
Inadequate water detected
Inadequate water detected
Hot tub in priming mode
Temperature unknown
Temperature not current or in Economy or Sleep mode.
sHOCK HaZard!
nO user serViCeaBle parTs.
A�WAYS TEST WATER TEMPERATURE
PRIOR TO ENTRY USING THE TOPSIDE
11