Technical Specifications - Salamander CT FORCE series Installation And Warranty Manual

General specifications – CT Xtra & CT Bathroom
Applications
All Salamander pumps are designed to boost low pressure hot and cold supplies from
cistern-fed services. When supplies from a water heater or a combination boiler are to be
boosted contact the Salamander PumpWise helpline on 0191 516 2002 for guidance.
Voltage
230 volts, 50 Hz.
Motor type
Capacitor start and run induction type motor with stainless steel shaft and in-built resetting
thermal protection (complies with BS5000 part 11).
Maximum head
All CT Xtra and CT Bathroom pumps are rated for a maximum static head of 10 metres.
(100 kPa / 1.0 bar)
Anti-vibration couplers
Do not bend
Please refer to the Technical Specifications table for information on which AV Couplers are
supplied with each pump.
Mechanical seals
Rotary mechanical face seals are used. Scale deposits in water supplies can cause the
mechanical seal to stick if left for long periods without use. The pump must be run for at least
five minutes every four weeks to 'exercise' all working parts.
Connections
¾" BSP male.
Initiation
Only applies to positive head pumps. Fully automatic, flow operated, requiring 1 litre in 30 sec
per side or 2 litres in 30 sec mixed.
Temperature
Maximum fluid temperature 60ºC.
Pump noise
Salamander has engineered this product range to be as quiet as possible, however no pump
is completely silent. Correct installation (anti-vibration couplers straight, rubber feet fitted)
will minimise noise, vibration and transmission noise.
Standards and approvals
Splash proof rating IPX2; complies with the requirements of
current British and European safety standards for household and
similar electrical appliances; meets with Compliance with European
Community Directives (CE). Due to continuous improvement and
updating specifications may be altered without prior notice.
The CT Xtra and CT Bathroom ranges of pumps are also fully WRAS
approved. CT Xtra has also been awarded Quiet Mark.
18
Technical specifications - CT Force
Part No. Description Specification Performance
Electrical Pump
Input Type
CT FORCE
Force 15PT 1.5 Bar Twin End 3A 110
 
Force 15IPT Positive Head Shower (1.1)
Pump
Force 20PT 2.0 Bar Twin End  3A  150
Force 20IPT Positive Head Shower (1.5)
Pump
Force 30PT 3.0 Bar Twin End  3A  220
Force 30IPT Positive Head Shower (2.2)
Pump
Force 20PS 2.0 Bar Single End  3A  150
Force 20IPS Positive Head Shower (1.5)
Pump
Force 30PS 3.0 Bar Single End  3A  210
Force 30IPS Positive Head Shower (2.1)
Pump
CT FORCE Universal Pumps
Force 15TU 1.5 Bar Twin End 3A 110
 
Force 15ITU Positive and Negative (1.1)
Head Shower Pump
Force 20TU 2.0 Bar Twin End 3A 150
 
Force 20ITU Positive and Negative (1.5)
Head Shower Pump
Force 30TU 3.0 Bar Twin End 3A 220
 
Force 30ITU Positive and Negative (2.2)
Head Shower Pump
Force 20SU 2.0 Bar Single End 3A 150
 
Force 20ISU Positive and Negative (1.5)
Head Shower Pump
Force 30SU 3.0 Bar Single End 3A 210
 
Force 30ISU Positive and Negative (2.1)
Head Shower Pump
Connection Type Pump Volumetrics
Pump Hoses Isolators Dimensions
¾"
130 150 22mm 4.96 180 120 160

(1.3) (1.5) 21mm
¾" 4.97 180 120 160
180 200 22mm 
(1.8) (2.0) 21mm
¾" 6.22 210 120 160
260 300 22mm 
(2.6) (3.0) 21mm
¾" 4.33 183 120 160
180 200 22mm 
(1.8) (2.0) 21mm
¾" 5.61 213 120 160
260 300 22mm 
(2.6) (3.0) 21mm
130 150 ¾" 22mm 5.53 180 125 315

(1.3) (1.5) 21mm
180 200 ¾" 22mm 5.57 180 125 315

(1.8) (2.0) 21mm
260 300 ¾" 22mm 6.79 210 125 315

(2.6) (3.0) 21mm
180 200 ¾" 22mm 4.96 183 125 315

(1.8) (2.0) 21mm
260 300 ¾" 22mm 6.20 213 125 315

(2.6) (3.0) 21mm
Packed Pump
Volumetrics
Dimensions
6.02 298 218 205
6.03 298 218 205
7.34 298 218 205
5.17 298 218 205
6.48 298 218 205
6.75 298 218 360
6.82 298 218 360
8.10 298 218 360
5.94 298 218 360
7.24 298 218 360
19