Related Manuals for Kaptur KP2000
Summary of Contents for Kaptur KP2000
- Page 1 KP2000 Linear CCD Barcode Scanner User Manual KP2000 User Manual Version 1.0-EN www.kaptur-id.com...
- Page 2 The device is manufactured by Trovi Technology CO., LTD. Kaptur brand, logos and Kaptur slogans are prorietary of Trovi Technology CO.,LTD. and TechSigno srl While the information found in this manual has been accurately verified, Trovi Technology assumes no liability for errors that may be herein contained or for damage to property or persons resulting from an improper use of the same or the software derived from it. Trovi Technoogy reserves the right to change the contents and the form of this document as well as to modify the product specifications at any time. The information contained in this document is property of Trovi Technology to whom all rights are reserved. No part of this document may be photocopied, reproduced or translated in another language without express written consent by Techsigno srl.
-
Page 3: Table Of Contents
Scan Reading Mode ............................. 14 Buzzer Setup ................................ 14 Symbologies Selection ............................15 UPC-A ......................................15 UPC-A Add-On 2 or 5 Digit ................................15 UPC-E ......................................16 UPC-E Add-On 2 or 5 Digit ................................16 EAN 13 ......................................17 EAN-13 Add-On 2 or 5 Digit ................................17 EAN 8 ......................................18 EAN-8 Add-On 2or 5 Digit ................................18 Code 39 ......................................19 Codabar ......................................19 Code93 ......................................20 Code 128 ......................................20 Interleaved 2 of 5 ................................... 20 Code 32 ......................................21 ASCII Table ..................................... 22 ASCII Code Value .................................... 23 Specifications ..........................24 KP2000 User Manual Version 1.0-EN 3 of 33... - Page 4 Technical specifications .......................... 24 Supported Barcode & Default setting for each barcode ................25 Troubleshooting ............................. 26 Maintenance ..........................27 Assembling the stand ........................ 28 Installing the Driver for USB VCOM Mode ................. 29 Disable digital signature check ........................ 29 Test barcode ........................... 33 4 of 33 KP2000 User Manual Version 1.0-EN...
-
Page 5: Safety Information
Do not dispose of these products in unsorted municipal refuse. Return the product to an authorized collection center to avoid damage to the environment or human health caused by uncontrolled disposal of waste and to promote the sustainable re cycling of materials Improper disposal of the product by the user entails the application of administrative sanctions provided by law RoHS This device and all its components, subcomponents and consumables were produced in accordance with Eurotpean directive 2002/95/EC also known as RoHS (Restrictions on the use of certain Hazardous Substances). This directive serves to reduce the polluting substances used in electronic devices. Antistatic devices Before working on the device it is necessary to apply the correct antistatic procedures to avoid possible damage by ESD (Electro Static Discharge) on the internal circuitry. Label The product label is showed below KP2000 User Manual Version 1.0-EN 5 of 33... -
Page 6: Provisions Used
Definition Read/write register Read only register Written register meaning Hexadecimal numbering the hexadecimal numbers are indicated with an H suffix example or in form 0x… : Example 2A3BH or 0x2A3B Symbology used in the definitions table: Symbol / Text Definition Symbol/Text Description Input Output I/O Bi-Directional Passive ▬ Model specific Depends on the device Not connected Reserved User reserved for Kaptur must remained disconnected Signal active low Notified potential danger or possible malfunctioning Instructions that must be followed in order to guarantee the device functions correctly 6 of 33 KP2000 User Manual Version 1.0-EN... -
Page 7: Technical Assistance
Technical Assistance If you have a technical question regarding the product’s installation or detect a problem with the device’s operation send an email to technical support at email: support@kaptur-id.com.com. Before returning any materials for any reason it is necessary to send an email to technical support at Kaptur at the above address which includes the following information: Model Ø Serial number Ø Detailed and complete description of the malfunction Ø Your company’s information Ø The reference person within your company Ø In response to your mail you will receive an RMA number (Returned Material Authorization) which authorizes the material’s return. The device must be returned in a protective antistatic bag and adequately packaged to ensure that the product is well protected during transport. -
Page 8: Getting Started
Getting Started Packaging Information Inside the standard packaging you will find: A Barcode Reader, a flexible stand (optional), the Quick Guide Part of the scanner Use a piece of dry and soft cloth when cleaning the scanner. Be carefull and do not scrap the reading windows. 8 of 33 KP2000 User Manual Version 1.0-EN... -
Page 9: Installation
Installation Connect Scanner to computer Switch Off the Computer Refer to the below pictures, connect the USB Cable to the computer Ensure tha all the connection are secure Switch On the Computer. If installation is correct the LED ① will lights Up and the Buzzer ⑤ will emit a beep. Disconnect Scanner from Computer Switch Off the computer and unplug the USB Cabe Restore factory default parameters To restore the factory default parameters read the below barcodes in sequence Start Configuration((+SETF)) Set All default((+RETF)) End Configuration((+ENDF)) Programming instruction and example To set the device just scan the related code. Example Start Configuration((+SETF)) Set All US Keyboard((+B2A)) End Configuration((+ENDF)) For more and detailed information howmto configure the scanner please refere to the Settings chapter KP2000 User Manual Version 1.0-EN 9 of 33... -
Page 10: Indication
In this configuration the scanner always keeps scanning, and it does not matter when the trigger button is pressed or duration is elapsed. If a valid code is readed the scanner will emit a beep. Decode illumination and aim pattern The scanner for a better quality images use a with light to illuminate the code. The effectiveness of the illumination decreases as the distance to the target increases. The scanner will project the aiming red patter during the code capture Vertical centering read The scanner reads only the barcode centered by the aimer in vertical direction. However, the scanner will read either one of two barcodes which are positioned horizontally. See the below example. 10 of 33 KP2000 User Manual Version 1.0-EN... -
Page 11: Setting
Setting To configure the scanner it is necessary to follow the sequence: Start Configuration((+SETF)) Parameter to configure (one or more in sequence) End Configuration((ENDF)) Note: The default factory settings is indicated with “Default ” System Information Start Configuration((+SETF)) Set All default((+RETF)) End Configuration((+ENDF)) Interface configuration The scanner support different interface, USB HID and USB Virtual COM Start Configuration((+SETF)) USB HID((+A1C)) USB Virtul COM((+A1D)) End Configuration((+ENDF)) When the scanner is configured in USB Virtual COM the Driver have to be installed on Windows PC KP2000 User Manual Version 1.0-EN 11 of 33... -
Page 12: Language Keyboard Setting
Language Keyboard Setting Is possible to configure the scanner for different keyboard Layout just reading the below barcode Start Configuration((+SETF)) USA((+B2A)) Default Italian((+B2B)) Spanish((+B2C)) French((+B2D)) Germany((+B2G)) Japan((+B2F)) Portugal((+B2G)) End Configuration((+ENDF)) Select Terminator It is possible to add a terminator at the and of the trasmission of the code readed. The selection can be “None” - “Return (CR)” - “TAB” - “Return/Line Feed (CR/LF)”. Start Configuration((+SETF)) None((+B9A)) CR((+B9B)) Default TAB((+B9C)) ESC((+B9D)) End Configuration((+ENDF)) 12 of 33 KP2000 User Manual Version 1.0-EN... -
Page 13: Add Prefix / Suffix
Add Prefix / Suffix Is it possible to add a Prefix or a Suffix at any code read. The structure of the trasmitted code will be Prefix Barcode Suffix Prefix and Suffic can be max 10 ASCII chatacters For the ASCII Table refere to the chatper relative chapter In order to add the Prefix or Suffix procede as indicate below Scan the barcode “Start Configuration” Check the ASCII table and get the ASCII Code for the Character to add Scan the barcode of ASCII Scan End Configuration Start Configuration((+SETF)) ADD Prefix((+E4A)) ADD Suffix((+E5A)) End Configuration((+ENDF)) Example: Add character “+” as prefix On the ASCII Table the character “+” is equal to 2B Start Configuration((+SETF)) Add Prefix End Configuration((+ENDF)) The defualt value for Prefix and Suffix is 00 To remove the Prefix or Suffix procede as per configuration procedure and scan ASCII 00 KP2000 User Manual Version 1.0-EN 13 of 33... -
Page 14: Scan Reading Mode
Contin./Time Out Off((+E1F)) trigger to read a code. In this configurationthe scanner star reading in continuos mode at power on, and stay always on. In this configuration is not necessary Continuos((+E1H)) press the trigger to read a code. End Configuration((+ENDF)) Buzzer Setup The buzzer can be configured to emit the sound at power on and at good read Start Configuration((+SETF)) Buzzer On or Off at power on of the Power Beep On((+EBA)) Default Power Beep Off((+EBB)) scanner Buzzer On or Off after a good read Good Read On((+ECA)) Default Good Read Off((+ECB)) End Configuration((+ENDF)) 14 of 33 KP2000 User Manual Version 1.0-EN... -
Page 15: Symbologies Selection
Symbologies Selection All the symbologies indicated on the table 1 are enabled as default parameter. To increse the speed on decoding time in some case it is necessary to disable the 2D Symbologies. UPC-A Start Configuration((+SETF)) Enable/ Disable UPC-A Code UPC-A Disabled((+F1A)) UPC-A Enabled((+F1B)) Default UPC-A Convert to EAN 13 Convert OFF(+F3A)) Default Convert ON((+F3B)) UPC-A Trasmit Check Character Trasmit Check OFF((+F4A)) Trasmit Check ON((+F4B)) Default End Configuration((+ENDF)) UPC-A Add-On 2 or 5 Digit Start Configuration((+SETF)) Enable/ Disable UPC-A Add-On None((+F8A)) Default Number of Digit 2 digit((+F8B)) 5 digit((+F8C)) Number of Digit 2 or 5 digit((+F8D)) AUTO_Enable ((+F8E)) End Configuration((+ENDF)) KP2000 User Manual Version 1.0-EN 15 of 33... -
Page 16: Upc-E
UPC-E Start Configuration((+SETF)) Enable/ Disable UPC-E Code OFF((+G1A)) ON((+G1B)) Default UPC-E Convert to UPC-A OFF((+G3A)) Default ON((+G3B)) UPC-E Trasmit Check Character ON((+G4B)) Default OFF((+G4A)) UPC-E Truncate Leading Zero ON((+G7B)) OFF((+G7A)) Default End Configuration((+ENDF)) UPC-E Add-On 2 or 5 Digit Start Configuration((+SETF)) Enable/ Disable UPC-E Add-On 2 of 5 None((+G8A)) Number of Digit 2digit((+G8B)) 5digit((+G8C)) Number of Digit 2 or 5 digit((+G8D)) AUTO_Enable ((+G8E)) End Configuration((+ENDF)) 16 of 33 KP2000 User Manual Version 1.0-EN... -
Page 17: Ean 13
EAN 13 Start Configuration((+SETF)) Enable/ Disable EAN 13 Code OFF((+H1A)) ON((+H1B)) Default EAN 13 Trasmit Check Character ON((+H3B)) Default OFF((+H3A)) End Configuration((+ENDF)) EAN-13 Add-On 2 or 5 Digit Start Configuration((+SETF)) Enable/ Disable EAN 13 Add-On 2 or 5 None((+H6A)) Default Number of Digit 2 Digit((+H6B)) 5 Digit((+H6C)) Number of Digit 2or 5 Digit((+H6D)) AUTO_Enable ((+H6E)) End Configuration((+ENDF)) KP2000 User Manual Version 1.0-EN 17 of 33... -
Page 18: Ean 8
EAN 8 Start Configuration((+SETF)) Enable/ Disable EAN 8 Code OFF((+I1A)) ON((+I1B)) Default EAN 8 Trasmit Check Character ON((+I3B)) Default OFF((+H3A)) End Configuration((+ENDF)) EAN-8 Add-On 2or 5 Digit Start Configuration((+SETF)) Enable/ Disable EAN 13 Add-On 2 or 5 None((+I6A)) Default Number of Digit 2 digit((+I6B)) 5 digit((+I6C)) Number of Digit 2 or 5 digit((+I6D)) AUTO_Enable ((+I6E)) End Configuration((+ENDF)) 18 of 33 KP2000 User Manual Version 1.0-EN... -
Page 19: Code 39
Code 39 Start Configuration((+SETF)) Enable/ Disable Code 39 OFF((+J1A)) ON((+J1B)) Default Code 39 Trasmit Check Character ON((+J3B)) Character OFF((+J4A)) Defaut Code 39 Min Length Code 39 Max Length (Default 01) (Default 50) <01H-50H>((+J6A)) <01H-50H>((+J7A)) Std Code39 ((+J9A)) Default Full ASCII Code39 ((+J9B)) Trioptic CODE39 ((+J9C)) End Configuration((+ENDF)) Codabar Start Configuration((+SETF)) Enable/ Disable Codabar ON((+K1B)) Default OFF((+K2A)) Codabar Trasmit Check Character OFF((+K4A)) Default ON((+K4B)) Codabar Trasmit End Character OFF((+K9A)) ON((+K9B)) Default End Configuration((+ENDF)) KP2000 User Manual Version 1.0-EN 19 of 33... -
Page 20: Code93
Code93 Start Configuration((+SETF)) Enable/ Disable Code93 OFF((+L1A)) ON((+L1B)) Default Code93 Trasmit Check Character ON((+L4B)) OFF((+L4A)) Default End Configuration((+ENDF)) Code 128 Start Configuration((+SETF)) Enable/ Disable Code 128 OFF((+M1A)) ((+M1B)) Default Code128 Trasmit Check Character ON((+M4B)) ((+M4A)) Default End Configuration((+ENDF)) Interleaved 2 of 5 Start Configuration((+SETF)) Enable/ Disable Interleaved 2 of 5 OFF((+N1A)) ON((+N1B)) Default Interleraved Trasmit Check Character ON((+N4B)) Default OFF((+N4A)) End Configuration((+ENDF)) 20 of 33 KP2000 User Manual Version 1.0-EN... -
Page 21: Code 32
Code 32 Start Configuration((+SETF)) Enable/ Disable Code 32 ON((+S1B)) OFF((+S1A)) Default Code32 Trasmit Check Character OFF((+S4A)) Default ON((+S4B)) Code32 Trasmit “A” OFF((+S8A)) Default ON((+S8B)) End Configuration((+ENDF)) KP2000 User Manual Version 1.0-EN 21 of 33... -
Page 22: Ascii Table
ASCII Table NUL DLE SOH DC1 STX DC2 “ ETX DC3 EOT DC4 ENQ NAK ACK SYN & BEL ETB ‘ CAN SUB ESC < > DEL To have the right code select the column and that the row. Example: To value of the “A” is 41 Column 4 Row 1 - the value of “+” is 2B Column 2 Row B Use the ASCII Code Value to set the value 22 of 33 KP2000 User Manual Version 1.0-EN... -
Page 23: Ascii Code Value
ASCII Code Value KP2000 User Manual Version 1.0-EN 23 of 33... -
Page 24: Specifications
UPC-A, UPC-E, EAN-13, EAN-8, ISBN, ISSN, Code 39, Code 38 Full Ascii, Code 32, Interleaved 2 of 5, Decode capability Industrial 2 of 5, Matrix 2 of 5, Codabar, Code 128, UCC/ENA 128, Code 93, Code 11, MSI/Plessey Indicator Beeper, LED Interface supported USB Keyboard, USB virtual COM Dimensions Height x Width × Depth - 90 × 70 × 164mm Weight 190g, without cable Cable Straight 2.0m Case material PC+TPU Operating 0°to 40°C Temperature Storage -40°to 60°C Humidity 5% to 95% (non-condensing) Program upgrade Online EMC: EN55022, EN55024 Electrical Safety: EN60950 Safety Drop resistance: Multiple Drop 1.2m Protection: IP41 24 of 33 KP2000 User Manual Version 1.0-EN... -
Page 25: Supported Barcode & Default Setting For Each Barcode
UPC-A √ √ √ (12) UPC-E √ √ √ (13) EAN-13 √ √ √ (8) EAN-8 √ √ √ Code 39 √ Interleaved 2 of 5 √ Codabar √ Code 128 √ √ Code 93 √ Code 32 √ (16) Notes Fixed-length barcodes. The settings for GS1 DataBar Truncated and GS1 DataBar must be the same. The following barcodes are supported but non enabled as factory default. Ask factory for settings CODE 32 - CODE 11 - MSI / Plessey - China Post Code - Matrix 2 of 5 - Industrial 2 of 5 - UCC/EAN128 KP2000 User Manual Version 1.0-EN 25 of 33... -
Page 26: Troubleshooting
For a USB-HID keyboard or a keyboard wedge the host. host type parameters or editing configuration, ensure the system options. programmed for the correct keyboard type and language, and the CAPS LOCK key is in the correct state. Contact your distributor or the manufactory Others technical support. 26 of 33 KP2000 User Manual Version 1.0-EN... -
Page 27: Maintenance
Maintenance Cleaning the exit window is the only maintenance required. A dirty window may affect scanning accuracy. Do not allow any abrasive material to touch the w indow. Remove any dirt particles with a damp c loth. Wipe the window using a tissue moistened with water. Do not spray water or other cleaning liquids directly into the w indow. Use a piece of soft and dry cloth when cleaning the s canner. KP2000 User Manual Version 1.0-EN 27 of 33... -
Page 28: Assembling The Stand
Assembling the stand Standing is an optional part you can order separatelly. Below the instruction how to assembly See the figure above, tighten the s crews. Bend the neck to the desired position for scanning and insert the scanner Picture 2 Screw mounting: Fix the flexible stand on the working station with right screw for the material of the working station (ex. Wood). Ensure the flexible stand is fixed and stable. Screws are not included. Adhesive tape mounting: ①Peel the paper liner off one side of each piece of tape and place the sticky surface over each of the three rectangular tape holders. ②Peel the paper liner off the exposed sides of each piece of tape and press the stand on a flat surface until it is secure. Ensure the flexible stand is fixed and stable. Adhesive Tape are not included. 28 of 33 KP2000 User Manual Version 1.0-EN... -
Page 29: Installing The Driver For Usb Vcom Mode
Operating System before the launch of the executable (this will require a reboot). See Disable Digital Signature Check chapter Plug the Kaptur device to your PC and scan the Enable USB Virtual COM QR code in order to switch to serial emulation. The driver just installed will automatically setup your device in few moments In you are experiencing other kind problems during the driver installation, please try to install VCP_V1.4.0_Setup.exe... - Page 30 Choose Troubleshoot from the options menu it appears. Choose Advanced options from the Troubleshoot menu. 30 of 33 KP2000 User Manual Version 1.0-EN...
- Page 31 Choose Startup Settings from the Advanced options menu. Click Restart. KP2000 User Manual Version 1.0-EN 31 of 33...
- Page 32 The computer will restart. Press the F7 key from the keyboard when the following menu appears on the screen. The system will boot with the digital signature check disabled. This will allow installing any unsigned USB Driver. After a reboot of the system, the digital signature check will be enabled again. The drivers that have already been installed will remain on your system, but if you want to install new unsigned drivers, you will need to perform this procedure again. 32 of 33 KP2000 User Manual Version 1.0-EN...
-
Page 33: Test Barcode
Test barcode UPC-A Value 123456790124 UPC-E Value 01234565 UPC-E(1) Value “01234565” EAN 13 Value 1234567890128 EAN 8 Value 12345670 ISBT/ISSN Value 9781234567897 CODE 39 Value 1234-ABCD Code Interleaved 2 of 5 Value 0123456784 CODABAR Value A12345678$B CODE128 Value A12345678B UCC ENA128 Value 0101234567890128 Code 93 Value ABC-1234-/+ Code 32 Value 87654612 A87654612 KP2000 User Manual Version 1.0-EN 33 of 33...