Related Manuals for Kaptur KP2200
Summary of Contents for Kaptur KP2200
- Page 1 KP2200 Imager Barcode Scanner User Manual KP2200 User Manual Version 1.2-EN www.kaptur-id.com...
- Page 2 The device is manufactured by Trovi Technology CO., LTD. Kaptur brand, logos and Kaptur slogans are prorietary of Trovi Technology CO.,LTD. and TechSigno srl While the information found in this manual has been accurately verified, Trovi Technology assumes no liability for errors that may be herein contained or for damage to property or persons resulting from an improper use of the same or the software derived from it. Trovi Technoogy reserves the right to change the contents and the form of this document as well as to modify the product specifications at any time. The information contained in this document is property of Trovi Technology to whom all rights are reserved. No part of this document may be photocopied, reproduced or translated in another language without express written consent by Techsigno srl.
-
Page 3: Table Of Contents
Language keyboard Setting ..........................12 Inter-character delay ............................12 Scan Reading Mode ............................. 12 Trigger mode ....................................13 Continuos mode ..................................... 13 Presentation Mode ..................................13 Buzzer Setup ................................ 13 Power ON ....................................... 13 Success Read ....................................13 Illunimation and Aiming ............................14 Lighting ......................................14 Aim ........................................ 14 Add Prefix / Suffix ..............................15 Configure Prefix ..................................... 16 Configure Suffix ..................................... 16 Select Terminator ..............................17 Symbologies Selection ............................18 Enable & Disable all Barcodes ............................... 18 EAN /UPC ....................................... 18 Code 128 ......................................18 KP2200 User Manual Version 1.2-EN 3 of 36... - Page 4 MicroPDF ....................................... 21 Trioptic ......................................21 Codeblock F ....................................21 Straight ......................................21 Telepen ......................................22 Maxicode ....................................... 22 Code32 ......................................22 More setting for 2D Symbologies ......................... 23 Setting the output of the Chinese content 2D code ........................23 ASCII Table ..................................... 24 ASCII Code Value .................................... 25 Restore factory default setting ..........................26 Specifications ..........................27 Technical specifications .......................... 27 Supported Barcode & Default setting for each barcode ................28 Troubleshooting ........................29 Maintenance ..........................30 Assembling the stand ........................ 31 Installing the Driver for USB VCOM Mode ................. 32 Disable digital signature check ........................ 32 Test barcode ........................... 36 4 of 36 KP2200 User Manual Version 1.2-EN KP2200 User Manual Version 1.2-EN...
-
Page 5: Safety Information
Do not dispose of these products in unsorted municipal refuse. Return the product to an authorized collection center to avoid damage to the environment or human health caused by uncontrolled disposal of waste and to promote the sustainable re cycling of materials Improper disposal of the product by the user entails the application of administrative sanctions provided by law RoHS This device and all its components, subcomponents and consumables were produced in accordance with Eurotpean directive 2002/95/EC also known as RoHS (Restrictions on the use of certain Hazardous Substances). This directive serves to reduce the polluting substances used in electronic devices. Antistatic devices Before working on the device it is necessary to apply the correct antistatic procedures to avoid possible damage by ESD (Electro Static Discharge) on the internal circuitry. Label The product label is showed below KP2200 User Manual Version 1.2-EN 5 of 36... -
Page 6: Provisions Used
Read/write register Read only register Written register meaning Hexadecimal numbering the hexadecimal numbers are indicated with an H suffix example or in form 0x… : Example 2A3BH or 0x2A3B Symbology used in the definitions table: Symbol / Text Definition Symbol/Text Description Input Output I/O Bi-Directional Passive ▬ Model specific Depends on the device Not connected Reserved User reserved for Kaptur must remained disconnected Signal active low Notified potential danger or possible malfunctioning Instructions that must be followed in order to guarantee the device functions correctly 6 of 36 KP2200 User Manual Version 1.2-EN KP2200 User Manual Version 1.2-EN... -
Page 7: Technical Assistance
Technical Assistance If you have a technical question regarding the product’s installation or detect a problem with the device’s operation send an email to technical support at email: support@kaptur-id.com.com. Before returning any materials for any reason it is necessary to send an email to technical support at Kaptur at the above address which includes the following information: Model Ø Serial number Ø Detailed and complete description of the malfunction Ø Your company’s information Ø The reference person within your company Ø In response to your mail you will receive an RMA number (Returned Material Authorization) which authorizes the material’s return. The device must be returned in a protective antistatic bag and adequately packaged to ensure that the product is well protected during transport. -
Page 8: Getting Started
Getting Started Packaging Information Inside the standard packaging you will find: A Barcode Reader, a flexible stand (optional), the Quick Guide Part of the scanner Use a piece of dry and soft cloth when cleaning the scanner. Be carefull and do not scrap the reading windows. 8 of 36 KP2200 User Manual Version 1.2-EN KP2200 User Manual Version 1.2-EN... -
Page 9: Installation
Installation Connect Scanner to computer Switch Off the Computer Refer to the below pictures, connect the USB Cable to the computer Ensure tha all the connection are secure Switch On the Computer. If installation is correct the LED ① will lights Up and the Buzzer ⑤ will emit a beep. Disconnect Scanner from Computer Switch Off the computer and unplug the USB Cabe Restore factory default parameters To restore the factory default parameters read the below barcode Restore to factory default Programming instruction and example To set the device just scan the related code. Example Set US Keyboard Style KP2200 User Manual Version 1.2-EN 9 of 36... -
Page 10: Indication
In this configuration the scanner always keeps scanning, and it does not matter when the trigger button is pressed or duration is elapsed. If a valid code is readed the scanner will emit a beep. Decode illumination and aim pattern The scanner for a better quality images use a with light to illuminate the code. The effectiveness of the illumination decreases as the distance to the target increases. The scanner will project the aiming red patter during the code capture Vertical centering read The scanner reads only the barcode centered by the aimer in vertical direction. However, the scanner will read either one of two barcodes which are positioned horizontally. See the below example. 10 of 36 KP2200 User Manual Version 1.2-EN... -
Page 11: Setting
Setting To configure the scanner it is sufficent read the setting barcode. If the configurarion code is readed the scanner will emit a dual high frequency beep Note: The default factory settings is indicated with “Default ” Interface configuration The scanner has been configured in factory with the USB HID enabled. If it is necessary to change the interface scan one of the below codes USB HID interface To configure the scanner in USB HID operating mode scan the below code Enable USB HID (Default) USB Virtual COM To configure the scanner in USB Virtual COM mode. No other setting are necessary after this selection. Note: Driver have to be installed on Windows PC Enable USB Virtual COM mode KP2200 User Manual Version 1.2-EN 11 of 36... -
Page 12: Language Keyboard Setting
Language keyboard Setting It is possible configure the scanner for different keyboard layout just reading the below programming code. US Keyboard (Default) French Keyboard Hungarian Keyboard Italian Keyboard Japan Keyboard Spanish Keyboard Czech Keyboard Germany Keyboard Inter-character delay This delay is inserted after each data character transmitted. 3 msec delay 6 msec Scan Reading Mode Select one of the below code to select the reading mode 12 of 36 KP2200 User Manual Version 1.2-EN... -
Page 13: Trigger Mode
Trigger mode TRIGGER MODE In this configuration the scanner start when the trigger button is pressed and stay on until the trigger is released. At a good read the scanner stop Continuos mode In this configuration the scan start reading when a change of brightness is detected by the CMOS sensor (typically when a code is pass in front of the reader). In this configuration is not necessary press the trigger to read a code. Presentation Mode In this configuration the scan start reading in continuos mode when the trigger button is pressed. The scanner stop at the second pression of the Trigger. In this configuration is not necessary press the trigger to read a code. Buzzer Setup Power ON Buzzer On at power on of the scanner (Default) Buzzer OFF at power on of the scanner Success Read At success read the Buzzer will emit a sound (Default) At success read the Buzzer will be mute KP2200 User Manual Version 1.2-EN 13 of 36... -
Page 14: Illunimation And Aiming
Illunimation and Aiming Lighting Illuminating light enabed when the tigger button is pressed (Default) Illuminating light always ON Illuminating light always OFF Aim RED Aiming light enabed when the tigger button is pressed (Default) RED Aiming light always ON RED Aiming light always OFF 14 of 36 KP2200 User Manual Version 1.2-EN... -
Page 15: Add Prefix / Suffix
Add Prefix / Suffix Is it possible to add a Prefix or a Suffix at any code read. The structure of the trasmitted code will be Prefix Barcode Suffix Prefix and Suffic can be max 15 ASCII chatacters For the ASCII Table refere to the chatper relative chapter In order to add the Prefix or Suffix procede as indicate below Scan the barcode “Modify Prefix or Modify Suffix” Check the ASCII table and get the ASCII Code for the Character to add Scan the barcode of ASCI Scan the barcode Save Prefix or Suffix Example: Add character “+” as prefix On the ASCII Table the character “+” is equal to 2B Enable Prefix Scan value 2 on ASCII Table Scan Value B on ASCII Table Save Prefix or Suffix KP2200 User Manual Version 1.2-EN 15 of 36... -
Page 16: Configure Prefix
Configure Prefix Enable Prefix Disable Prefix (Default) Modify Prefix If Prefix is disabled (as per Default Configuration) the scanned doesn’t sent out it also if programmed. Be sure to enable Prefix after have programmed it. Configure Suffix Enable Suffix Disable Suffix (Default) Modify Suffix If Suffix is disabled (as per Default Configuration) the scanned doesn’t sent out it also if programmed. Be sure to enable Suffix after have programmed it. 16 of 36 KP2200 User Manual Version 1.2-EN... -
Page 17: Select Terminator
Select Terminator It is possible to add a terminator at the and of the trasmission of the code readed. The selection can be “None” - “Return (CR)” - “TAB” - “Return/Line Feed (CR/LF)”. None CR (Default) TAB CR / LF KP2200 User Manual Version 1.2-EN 17 of 36... -
Page 18: Symbologies Selection
Symbologies Selection All the symbologies indicated on the table 1 are enabled as default parameter. Is it possible to enable/disable every single code just reading the relative configuration code. To increse the speed on decoding time in some case it is necessary to disable the 2D Symbologies. Is it possible to Enable / Disable in block all the supported Barcodes. After have disabled all the barcode it is possible enable the single standard reading the relative code to enable it. Enable & Disable all Barcodes Enable All Barcode (Default) Disable All Barcodes EAN /UPC EAN/UPC Enable (Default) EAN/UPC Disabled EAN/UPC no addtional code EAN/UPC send additiona code Code 128 Code 128 Enable (Default) Code 128 Disabled Code 128 Enable ASCII Character Code 128 Enable ASCII Character 18 of 36 KP2200 User Manual Version 1.2-EN... -
Page 19: Code 39
Code 39 Code 39 Enable (Default) Code 39 Disabled Code 93 Code 93 Enable (Default) Code 93 Disabled Codebar Codebar Enable (Default) Codebar Disabled QR Code QR Code Enable (Default) QR Code Disabled Interleaved 2 of 5 Interleaved 2 of 5 Enable (Default) Interleaved 2 of 5 Disabled Industrial 25 Industrial 25 Enable (Default) Industrial 25 Disabled Matrix 2 of 5 KP2200 User Manual Version 1.2-EN 19 of 36... -
Page 20: Matrix 2 Of 5
Matrix 2 of 5 Enable (Default) Matrix 2 of 5 Disabled Code 11 Code 11 Enable (Default) Code 11 Disabled MSI MSI Enable (Default) MSI Disabled MSI Enable Check Digit MSI Disable Check Digit (Default) GS1 Databar GS1 Databar Enable (Default) GS1 Databar Disabled Datamatrix Datamatrix Enable (Default) Datamatrix Disabled PDF417 20 of 36 KP2200 User Manual Version 1.2-EN... -
Page 21: Aztec
PDF417 Enable (Default) PDF417 Disabled AZTEC Aztec Enable (Default) Aztec Disabled Hanhix Hanhix Enable (Default) Hanhix Disabled MicroPDF MicroPDF Enable (Default) MicroPDF Disabled Trioptic Trioptic Enable (Default) Trioptic Disabled Codeblock F Codeblock F Enable (Default) Codeblock F Disabled Straight KP2200 User Manual Version 1.2-EN 21 of 36... -
Page 22: Telepen
Straight Enable (Default) Straight Disabled Telepen Telepen Enable (Default) Telepen Disabled Maxicode Maxicode Enable (Default) Maxicode Disabled Code32 Code 32 Enable (Default) Code 32 Disabled 22 of 36 KP2200 User Manual Version 1.2-EN... -
Page 23: More Setting For 2D Symbologies
More setting for 2D Symbologies Setting the output of the Chinese content 2D code In order to display the correct Chinese data, the scanner have to be configured. GBK Format: Can be used in Notepad txt document. Unicode Format: Can be used in Word and QQ and micro-mail and other commonly used chat box input tool. Note: Most of the software is generally compatible with the GBK format and if you can not view the correct characters, try switching to Unicode mode GBK Format (Default) Unicode Format These are the most common settings. If more settings are required please contact the manufacturer. KP2200 User Manual Version 1.2-EN 23 of 36... -
Page 24: Ascii Table
ASCII Table NUL DLE SOH DC1 STX DC2 “ ETX DC3 EOT DC4 ENQ NAK ACK SYN & BEL ETB ‘ CAN SUB ESC < > DEL To have the right code select the column and that the row. Example: To value of the “A” is 41 Column 4 Row 1 - the value of “+” is 2B Column 2 Row B Use the ASCII Code Value to set the value 24 of 36 KP2200 User Manual Version 1.2-EN... -
Page 25: Ascii Code Value
ASCII Code Value KP2200 User Manual Version 1.2-EN 25 of 36... -
Page 26: Restore Factory Default Setting
Restore factory default setting To reset the parameter to factory refault. Use this code carefully and only if you are not sure how is configured the scanner. RESET TO FACTORY DEFAULTS 26 of 36 KP2200 User Manual Version 1.2-EN... -
Page 27: Specifications
2D Imager Area Image (640 x 480 pixel array) Decoding rate 200 times/sec Scanning angle ±60°, ±65°, ±42°(Skew, Pitch, Roll) Print contrast 25% minimum reflection difference UPC-A, UPC-E, UPC-E1, EAN-13, EAN-8, ISBN (Bookland EAN), ISSN, Code 39, Code 39 full ASCII, Code Decode capability 32, Trioptic Code 39, Interleaved 2 of 5, Industrial 2 of 5 (Discrete 2 of 5), Matrix 2 of 5, Codabar (NW7), Code 128, UCC/EAN 128, ISBT 128, Code 93, Code 11 (USD-8) Indicator Beeper, LED Interface supported USB Keyboard, USB virtual COM Operating mode Hand-held, Auto-detection (Optional) Dimensions Height x Width × Depth - 90 × 70 × 164mm Weight 190g, without cable Cable Straight 2.0m Case material PC+TPU Operating 0°to 40°C Temperature Storage -40°to 60°C Humidity 5% to 95% (non-condensing) Program upgrade Online EMC: EN55022, EN55024 Electrical Safety: EN60950 Safety Drop resistance: Multiple Drop 1.2m Protection: IP41 KP2200 User Manual Version 1.2-EN 27 of 36... -
Page 28: Supported Barcode & Default Setting For Each Barcode
(8) EAN-8 √ √ √ Code 39 √ Interleaved 2 of 5 √ Codabar √ Code 128 √ √ Code 93 √ GS1 DataBar √ (16) GS1 DataBar Truncated √ (16) GS1 DataBar Limited √ (16) GS1 DataBar Expanded √ PDF417 √ DataMatrix √ QR Code √ Aztec Code √ Notes Fixed-length barcodes. The settings for GS1 DataBar Truncated and GS1 DataBar must be the same. 28 of 36 KP2200 User Manual Version 1.2-EN... -
Page 29: Troubleshooting
Scanner is not programmed to settings. Scanned data is incorrectly displayed on work with the host. Check For a USB-HID keyboard or a keyboard wedge the host. scanner host type parameters or configuration, ensure the system editing options. programmed for the correct keyboard type and language, and the CAPS LOCK key is in the correct state. Contact your distributor or the manufactory Others support centre. KP2200 User Manual Version 1.2-EN 29 of 36... -
Page 30: Maintenance
Maintenance Cleaning the exit window is the only maintenance required. A dirty window may affect scanning accuracy. Do not allow any abrasive material to touch the w indow. Remove any dirt particles with a damp c loth. Wipe the window using a tissue moistened with water. Do not spray water or other cleaning liquids directly into the w indow. Use a piece of soft and dry cloth when cleaning the s canner. 30 of 36 KP2200 User Manual Version 1.2-EN... -
Page 31: Assembling The Stand
Assembling the stand Standing is an optional part you can order separatelly. Below the instruction how to assembly See the figure above, tighten the s crews. Bend the neck to the desired position for scanning and insert the scanner Picture 2 Screw mounting: Fix the flexible stand on the working station with right screw for the material of the working station (ex. Wood). Ensure the flexible stand is fixed and stable. Screws are not included. Adhesive tape mounting: ①Peel the paper liner off one side of each piece of tape and place the sticky surface over each of the three rectangular tape holders. ②Peel the paper liner off the exposed sides of each piece of tape and press the stand on a flat surface until it is secure. Ensure the flexible stand is fixed and stable. Adhesive Tape are not included. KP2200 User Manual Version 1.2-EN 31 of 36... -
Page 32: Installing The Driver For Usb Vcom Mode
Operating System before the launch of the executable (this will require a reboot). See Disable Digital Signature Check chapter Plug the Kaptur device to your PC and scan the Enable USB Virtual COM QR code in order to switch to serial emulation. The driver just installed will automatically setup your device in few moments In you are experiencing other kind problems during the driver installation, please try to install VCP_V1.4.0_Setup.exe instead. - Page 33 Choose Troubleshoot from the options menu it appears. Choose Advanced options from the Troubleshoot menu. KP2200 User Manual Version 1.2-EN 33 of 36...
- Page 34 Choose Startup Settings from the Advanced options menu. Click Restart. 34 of 36 KP2200 User Manual Version 1.2-EN...
- Page 35 The computer will restart. Press the F7 key from the keyboard when the following menu appears on the screen. The system will boot with the digital signature check disabled. This will allow installing any unsigned USB Driver. After a reboot of the system, the digital signature check will be enabled again. The drivers that have already been installed will remain on your system, but if you want to install new unsigned drivers, you will need to perform this procedure again. KP2200 User Manual Version 1.2-EN 35 of 36...
-
Page 36: Test Barcode
Test barcode UPC-A Value 123456790124 UPC-E Value 01234565 UPC-E(1) Value “01234565” EAN 13 Value 1234567890128 EAN 8 Value 12345670 ISBT/ISSN Value 9781234567897 CODE 39 Value 1234-ABCD Code Interleaved 2 of 5 Value 0123456784 CODABAR Value A12345678$B CODE128 Value A12345678B UCC ENA128 Value 0101234567890128 Code 93 Value ABC-1234-/+ GS1 DataBar Value 0100123456784444 GS1 DataBar Limited Value 0101234567890128 GS1 DataBar Expanded Value 0112345678901231BCabc PDF417 Value This is a MicroPDF417 by Kaptur DataMatrix Value This is a Data Matrix by Kaptur QR Code Value This is a QR Code by Kaptur Aztec Value This is an Aztec Code by Kaptur 36 of 36 KP2200 User Manual Version 1.2-EN...