Viking K-1900-8-IP-EWP Product Manual page 19

C. Remote Access Operation Commands
The following commands can be entered after answering a call from the entry phone. The commands can also be entered on an
inbound call to the entry phone. After calling into the entry phone and the unit auto answers or someone answers the call by lifting
the handset, one or two beeps will be heard. If the access code has been disabled (two beeps heard), you can now enter the Remote
Access Operation Commands below. If an Access code has been programmed (one beep heard), enter the Access code digits. With
the correct code entered, two beeps will be heard and you can now enter the Remote Access Operation Commands below. The
Relay Mode must be set to "Door Strike" to be controlled by these commands.
Feature
Momentarily
Activate Relay 1
Latch Relay 1
Un-Latch Relay 1
Toggle Relay 1
Momentarily
Activate Relay 2
Latch Relay 2
Un-Latch Relay 2
Toggle Relay 2
Disconnect
* Note: Latching commands must be enabled in programming.
D. Keyless Entry Codes and One Time Use Keyless Entry Codes
Keyless entry codes may be used by the tenants to provide keyless entry. The K-1900-8-IP can be programmed with a combination of
up to 1000* keyless entry codes or one time use keyless entry codes. The keyless entry codes can be programmed to be from 1 to 6
digits in length. Each keyless entry code can be programmed to activate relay 1 and/or 2 in four different relay modes: Momentary,
Latch, Un-Latch and Toggle. To use a keyless entry code the tenant simply dials "#" followed by the entry code on the K-1900-8-IP's
keypad. After the one time use keyless entry code has been used, it is instantly cleared from the unit's memory. This is ideal for issuing
keyless entry codes to service personnel, etc.
Keyless entry codes can only be dialed while the handset is hung up in the Manual Dial Phone mode. In the Single and Multi-Number
Auto Dialer modes, keyless entry codes can be dialed while the handset is hung up or when the handset is first lifted, when some delay
has been programmed for Off Hook Dialing Delay.
E. Proximity Cards
Proximity cards can also be used by the tenants to provide keyless entry. The K-1900-8-IP can be programmed with up to 1000* proximity
card numbers. Each proximity card number can be programmed to activate relay 1 and/or 2 in four different relay modes: Momentary,
Latch, Un-Latch and Toggle. To use a proximity card, the tenant simply presents a preprogrammed proximity card within range
proximity card reader attached to the K-1900-8-IP. A short beep will be heard from the card reader indicating a card scan. If the card
matches a valid preprogrammed card number the relay will be activated and the visitor can now open the door or gate.
Proximity cards can be scanned at anytime, even while a call is in progress.
*Note: 1000 is the total number of Keyless Entry Codes and/or Proximity Card numbers that can be programmed in the Entry Code
Database.
**Note: Read range depends on the type of card and card reader being used.
F. 911 Calls
The K-1900-8-IP is not intended to be an emergency phone and does not try to automatically handle users that dial "911" after picking up
the handset. In the Manual Dial Phone mode, the "911" dialed by the user is passed on to the phone system, so it is up to the SIP phone
system or provider to route the call properly. In the Single and Multi-Number Auto Dialer modes, a speed dial of "911" can be programmed
with primary and rollover phone numbers, to route the calls appropriately. Some delay must be programmed for Off Hook Dialing Delay,
to give the user time to dial the "911" before they are automatically routed to another number or hear 3 beeps.
Touch Tone
Description
Command
QQ or
Momentarily activate relay 1 (1 or 2 digits, factory set to QQ).
___ ___
11 Latch* (continuously activate) relay 1.
10 Un-latch* (deactivate) relay 1.
1# Toggle* relay 1 from last position.
Q2 or
Momentarily activate relay 2 (1 or 2 digits, factory set to Q2).
___ ___
21 Latch* (continuously activate) relay 2.
20 Un-latch* (deactivate) relay 2.
2# Toggle* relay 2 from last position.
# Disconnects or forces the phone to hang up.
19
**
of the