Subscribe to Our Youtube Channel
Related Manuals for Milnor Miltrac
Summary of Contents for Milnor Miltrac
- Page 1 Published Manual Number/ECN: MATMLTRCAE/2018103A • Publishing System: TPAS2 • Access date: 03/06/2018 • Document ECNs: Latest Technical Reference Miltrac™ Controller PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.
- Page 3 MSOP0969BE/199816AV 1. Programming Programming Miltrac: Overview MSOP0971AE/199816AV Programming Miltrac: Initialize and Exit MSOP0972AE/199816AV Programming Miltrac: Configure MSOP0973AE/199816AV Stuffing Logic for the Miltrac Controller BIYCMC03/20150108 Programming Miltrac: Display Pages MSOP0974AE/199816AV Programming Miltrac: Names MSOP0975AE/199816AV 2. Supplemental Information Monitoring with Miltrac MSOP0976AE/199816AV...
-
Page 5: Limited Standard Warranty
(unless the time period is specifically extended for certain parts pursuant to a specific MILNOR published extended warranty) from our factory with no operating hour limitation. This warranty is contingent upon the equipment being installed, operated and serviced as specified in the operating manual supplied with the equipment, and operated under normal conditions by competent operators. -
Page 6: How To Get The Necessary Repair Components
• If the component is an electrical component, give the schematic number if known. • If the component is a motor or an electrical control, give the nameplate data from the used component. To write to the Milnor factory: Pellerin Milnor Corporation Post Office Box 400... -
Page 7: Trademarks
BNUUUU02 / 2017285A BNUUUU02 0000158094 A.3 7/13/17 1:53 PM Released Trademarks BNUUUU02.R01 0000158093 A.2 7/13/17 1:11 PM Released These words are trademarks of Pellerin Milnor Corporation and other entities: Table 1 Trademarks AutoSpot™ GreenTurn™ Milnor® PulseFlow® CBW® GreenFlex™ MilMetrix® PurePulse®... -
Page 19: Programming
Programming... -
Page 44: Stuffing Logic For The Miltrac Controller
BIYCMC03 (Published) Book specs- Dates: 20150108 / 20150108 / 20150108 Lang: ENG01 Applic: YCM Stuffing Logic for the Miltrac Controller The Miltrac controller uses stuffing logic to arrange cakes of goods so the receiving device is always loaded at its maximum capacity with compatible goods. The most common application is when dryers are loaded by Linear Costa devices. -
Page 51: Supplemental Information
Supplemental Information... - Page 59 The memory download box is used to store configuration and formula data for most current ® models of Milnor machines. Two types of download boxes (Figure 1) are available: one with a Transmit button on the front panel, and one without the button. The Transmit button is not ®...
- Page 60 =U]_bi 4_g^\_QT 2_h 1``\YSQdY_^c Figure 2: Rear View of Circuit Board View Legend DIP switch Software chip Location of Transmit button, if equipped Key switch Bd__[T\T]c 8]cTa_aTcX]V cWT 38? BfXcRW BTccX]Vb Use the following codes and their definitions to set the DIP switch positions for the equipment, as shown in Table 1.
- Page 61 Uses Memory Download Box WITHOUT Button Transmit Button Washer-extractor Models Miltron Controller for CBW System 8088 8088 98000-98003 80186 98004-99004 not supported Miltrac 80186 99005-9900B 8088 20000-20003 80186 FxW, FxP, and FxS Washer-extractor models Milrail Rail Controller 8088 8088 98000-98003...
-
Page 63: Troubleshooting
Troubleshooting...
Need help?
Do you have a question about the Miltrac and is the answer not in the manual?
Questions and answers