Draco 1020-1 Operating Instructions

Operating Instructions

1. Intended use. This Power Tool is intended for
industrial applications, for cutting sheet metal
(maximum capacity is indicated in the
Specifications), for use with cutting jaws and cutting
blades which are indicated in these operating
instructions or recommended by DRÄCO
2.

Initial Operation

Observe the rated voltage: The voltage of the power
source must match that given on the nameplate of the
machine. Machines for 230V can also be operated on
220 V power sources.

Switching ON and OFF

Switching ON: Slide the switch pad (109) forward
Switching OFF: Slide the switch pad (109) to the rear.
2. The material to be cut must always be free of oil or
grease. Always place the machines jaws flat on the work
piece.
3. Cut-outs: Drill a starting hole with a 12-14 mm diameter
drill. Circular cuts: Always cut counter clockwise and
from left to right.
4. Do NOT cut sheet metal along welding points. Do
NOT cut multi layer sheets, which exceed the
maximum cutting capacity.

Environmental protection

Recycling raw materials instead of waste
disposal. Machine, accessories and packaging should
be sorted for environment-friendly recycling.
These instructions are printed on recycling paper
manufactured without chlorine

Care and Maintenance

Before working on machine disconnect from power
supply by removing plug from socket.
Always keep the machine and the ventilation slots clean.
Oil the knife pin and knife at regular intervals.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorised customer services agent for
DRÄCO power tools

CE-Declaration of conformity

We declare under our sole responsibility that this product is in conformity with the following standards.
EG 98/37, EG 93/ 68 EWG, EG 04/108 EG und Normen DIN EN ISO 12100-1 , DIN EN ISO 12100-2 , EN 50 144, EN 55 014,
entspricht.
14 Susanne Draenert
For inside cutting, the shortest curve possible has
5.
a radius of 200 mm (±8"). If cutting a radius with
the right hand, cut from right to left. The outside
radius is unlimited.
6. For cutting out curved or circular inside patterns,
a 14 mm (± 1/2 ") hole, or a punched slot should
be made to insert the centre cutter.
7. If after cutting, a small strip remains this can
easily be trimmed off to the exact measurement,
without leaving a burr or any distortion of the
material. Just one side of the power tools can be
used for cutting also (e.g. along a marked line).
Lift the power tools out of the shavings while the
motor is running. Cut off longer shavings.
Both knife and jaws can be sharpened. After
8.
being sharpened or replaced, the knife at it's
lowest point should protrude the jaws by
approximately 3 mm. The knife should have
approximately 0,05 mm (0,005") play on each
side of the jaws, centring the cutter with spacing
shims supplied.
Every 200 operating ours have the cutting blade
9.
and cutting jaws sharpened at a specialist
workshop.
10. Ensure that the material to be cut is free of oil
and grease.

Noise/vibration information

Measured values determined according to EN 50 144.
Typically the A-weighted sound pressure level of the tool is
83 dB(A). The noise level when working can exceed 85 db
(A).
Wear ear protection!
The typical hand-arm vibration is below 2,5 m/s²

Warranty

DRÄCO tools carry a guarantee of 12 months from
date of delivery.
Damage attributable to normal wear and tear,
overload or improper handling will be excluded from
the guarantee. (e.g. blades/knifes and jaws)
In case of complaint please send the machine,
undismantled, to your dealer or the DRÄCO Service
Centre for electric power tools.
Operating Instructions for the metal shear 1020-1
To avoid any disturbance please read the following instructions:
For your safety:
1 2 3
1 Safe operation of this machine is possible only
when the operating instructions and the safety
precautions are read completely and the
instructions contained therein are strictly
observed.
2 The machine must not be used when damp and
must not be operated in a wet environment.
3 Always inspect cable and plug before using
machine. Only have damage repaired by a qualified
professional. Put the plug into the mains socket only
when the machine is switched off.
4+5 Always wears protective goggles, protective
gloves and heavy-duty shoes when working.
For further notes on safety refer to enclosed sheet
DRÄCO metal shears 1020-1
max. cutting capacity Art.nr. 61040-1
steel 400 N/mm² mm 2,0
stainless steel 600 N/mm² mm 1,5
stainless steel 800 N/mm² mm 1,3
aluminium 250 N/mm² mm 3,0
tightest radius mm 200
working speed m/min 5
strokes -1 2200
min
motor capacity Watt 500
weight kg 1,8
4 5
Do not carry the machine by the cable.
Always remove the plug from the power
supply socket before carrying out any work on
the machine, when interrupting work and when
not using the machine.
Always place the cable to the rear away
from the machine.
Apply the machine to the sheet metal only
when switched on.
Always provide for secure footing when
working.
Firmly clamp the workpiece if it dose not
remain stationary from its own weight.
The knife should not rub on the jaws:
Possible danger of cutting tool breakage.
Do not exceed the maximum allowable
material thickness especially when cutting over
doublers, folded joints or welded seams.
1020-1
spare parts
knife 010135
set of jaws BG35146
knife-pin set BG35155
Optionales Zubehör
metal-box 18000
adjustable guide S/01 up to 100 mm 10059
adjustable guide S/01 up to 250 mm 10060
adjustable guide S/01 up to 500 mm 10061
support roller metal 10077
61040-1 Gb - 1020-1.doc, , 7-12-2014