Advertisement
Making the Connections
LINE IN CONNECTION
This unit is able to connect your favorite audio device (e.g.
iPhone/Tablet/MP3 player,etc.). You can connect your
device by using a provided cable (3.5mm audio cable).
LINE IN function is automatically selected once the audio
cable is plugged in.
Warning
- To avoid excessive over amplified sound output, it is
recommended that the volume control is initially adjusted
to one third or less and then increase if required.
BATTERY OPERATION
1. Remove the battery compartment cover on the bottom of the
back of the unit by using a Phillips-head screw driver.
2. Insert three (3) "AA" size alkaline batteries (not included) as
indicated on the right diagram.
3. Replace the cover tightly before operating.
CAUTION:
- Replace all batteries at the same time.
- Do not mix old batteries with new batteries.
POWER ADAPTOR OPERATION
If you would like to purchase an external AC power adapter to save
on battery consumption, please refer to the specification on right.
Insert the DC plug of the power adaptor into the DC jack on the unit.
Plug the other end into a standard AC outlet.
CAUTIONS:
- The AC Adaptor has a polarized plug that fits into the wall outlet only one way.
If the plug does not fit properly, turn it over and try again. Do not force it.
BATTERY PRECAUTIONS
The precautions below should be followed when using batteries in this device:
1. Warning – Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
2. Use only the size and type of batteries specified.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. A
reversed battery may cause damage to the device.
4. Do not mix different types of batteries together (e.g. Alkaline, Rechargeable and Carbon-zinc) or old batteries
with fresh ones.
5. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.
6. Do not try to recharge a battery not intended to be recharged; it can overheat and rupture. (Follow the battery
manufacturer's directions.)
7. Remove the batteries promptly once its charge is low.
8. Clean the battery contact and also those of the device prior to installing the battery.
Operation
1
Connect the unit as described previously. Press the POWER button to turn the unit on;
the power indicator will light on.
USING A BLUETOOTH DEVICE
2
The Bluetooth pair indicator will
blink rapidly to indicate it is in the
pairing mode.
Note:
You can also press and hold the
PLAY/PAIR button to initiate the
pairing mode.
Switch on the Bluetooth function of
your Bluetooth compatible device
within three feet of the unit. You will
see "Mic Guy" appear on your device's
search list.
Note:
Please always refer to the user manual of your bluetooth device for detailed instructions.
Select "Mic Guy" to start pairing. Wait for completion of the pairing and the Bluetooth
indicator will light solid.
Note:
If your Bluetooth device prompts you for a passcode during the pairing process, please
enter "0000" to connect. If pairing fails, repeat steps 2-4. If you have paired before, a list
of previously searched results will be displayed. Select "Mic Guy" again. On some
Bluetooth devices (i.e.,computers), once pairing is complete, you must select your
Bluetooth device as "Use as Audio Device" or similar.
PLAY/PAUSE: Press the Play/Pause button on the Bluetooth device or on the unit to start.
SING-ALONG WITH BUILT-IN SONGS AND EFFECTS
3
There are 3 built-in songs and 3
sound effects in this sing-along
unit. You can press them one by
one to try.
Press Song 1, Song 2 or Song 3
button to play three different
songs. Press the button again to
stop. Press Effect 1, Effect 2 or
Effect 3 button to play three
different sound effects.
MICROPHONE CONNECTION
Connect the provided Mic Guy microphone into
the microphone jack. Please ensure that you lift the
microphone from the platfrom prior to using it.
Note:
- Do not drop or tap the microphone as damage to
the microphone or speaker may occur.
- Do not twirl the microphone cord as it will cause
damage to the encased wiring.
AC power adaptor specification
I
nput : AC 100-240V ~ 50-60Hz
Output DC
5V 0.6A
v
PLAY/PAIR
+
VOLUME
-
RECORD
SONG
EFFECT
1
2
3
1
2
3
u
PLAY/PAIR
+
VOLUME
-
RECORD
SONG
EFFECT
1
2
3
1
2
3
w
MICROPHONE
(sold separately)
Microphone jack
.
LINE IN jack
Battery
compartment
cover
ENERGY SAVING (AUTO POWER SYSTEM-APS)
The unit will automatically enter the Standby mode after 15
minutes in the following situations:
1. No button being pressed for 15 minutes.
2. No playback from your audio device for 15 minutes. The
playback of audio device had been stopped but the audio cable
is still plugged into the LINE IN jack.
3. Not singing to the microphone for 15 minutes. The Power
indicator will be turned off.
The unit can be resumed to turn on by pressing the Power button
once. APS is for energy saving purposes.
SING-ALONG WITH LINE IN MUSIC
4
Connect the audio device to the LINE IN jack
on the back of this unit. It will allow the audio
to be played through your unit. LINE IN
function is automatically selected once the
audio cable is plugged in.
Note:
• It is highly recommended to set the volume on
the auxiliary unit to 1/3 or lower to avoid
distortion.
SING-ALONG WITH MIC GUY
5
Connect the Mic Guy microphone into the
microphone jack at the back of the unit. Once
you lift the Mic Guy microphone you can see
the Microphone switch is located on the unit.
When the Mic Guy microphone is not sitting
on the platform, the microphone switch is
ON. When the Mic Guy is sitting back on the
platform, the microphone switch is OFF.
You can also connect an extra microphone
(not included) to another mic jack. The extra
microphone should have ON/OFF switch by
itself. Please also turn it ON before singing.
Note:
Please always lift the Mic Guy microphone when
you want to sing with the extra microphone
6
Adjust the volumn to a comfortable level by
pressing the button VOLUME + and
VOLUME - button.
RECORDING YOUR SINGING:
7
To record your singing as well as the music,
press the RECORD button; recording will
begin and the Record/Playback indicator will
blink. When you want to finish the recording,
press the RECORD button again. The
Record/Playback indicator will stop blinking
Note:
• There is 3 minutes and 40 seconds recording time.
• Please note that each time when the new
recording is being recorded, the existing recording
will be deleted.
POWER
ADAPTOR
(sold separately)
AUDIO DEVICE
(sold separately)
MIC 1
MIC 2
LINE IN
DC 5V IN
DC jack
y
MIC 1
y
MIC 2
x
LINE IN
DC 5V IN
V W
PLAY/PAIR
VOLUME
RECORD
SONG
1
2
3
1
y
PLAYBACK YOUR VOICE RECORDING:
8
To playback your voice recording,
you can press the PLAY/PAIR
button.
The Record/Playback indicator will
light on. Press the PLAY/PAIR
button again to stop.
YOUR
U
+
-
EFFECT
2
3
Microphone
(Mic Guy)
Advertisement
