Related Manuals for GRAUPNER Taifun
Summary of Contents for GRAUPNER Taifun
- Page 1 Manual Raceboat „Taifun“ X-Cat model to be powered by 2 Power Seven Engines No. 2280...
-
Page 3: Table Of Contents
Inhaltsverzeichnis For your notes ................4 Introduction .................5 Service Adresses ...............5 Intended use ................6 Package content ................6 Required components ..............6 Declaration of conformity ............7 Symbols explication ..............8 Safety notes ................8 Assembling of the model ............9 Apply the stickers: ..............11 Partlist ..................12 Electric wiring ................13 Controlling the two motors ............13 Telemetry ..................13... -
Page 4: For Your Notes
For your notes... -
Page 5: Introduction
Due to technical changes, the information in this manual is sub- ject to change without notice. Inform yourself in regular intervals on the Internet at www.graupner.de to stay up to date with the product and the instructions. This product complies with the legal national and European requirements. -
Page 6: Intended Use
Read the entire instructions carefully before connecting and using the module. Graupner / SJ is constantly working on the further development of all products; We must therefore reserve the right to change the scope of delivery in terms of form, technology and equipment. -
Page 7: Declaration Of Conformity
Declaration of conformity No. 2280 Raceboat Taifun Graupner/SJ declares that the product is conform to CE norms Technichal Data Raceboat Taifun Battery recommendation 2 x 2S oder 2 x 3S Lipo 900 x 285 x 170 mm with Power meassures... -
Page 8: Symbols Explication
Symbols explication Always observe the information marked with this warning picto- gram. Especially those which are additionally marked by CAUTION or WARNING. The signal word WARNING alerts you to possible seri- ous injuries, the signal word CAUTION for possible minor injuries. Note warns you of possible malfunctions. -
Page 9: Assembling Of The Model
Assembling of the model The fiberglass parts are all finished cropped. The wood laser parts are glued together using the pictures (superglue No. 5821) To install the servo base (4) in the fuselage, Stabilit Express no. 960.85. The position of the base is provided centrally in the fuse- lage. - Page 10 Use the hook and loop strap (20) to attach the batteries. The rubber sleeves (8) can be fixed with some superglue or alternatively with cable ties (optionally available under No. S8436) Always place the antenna of the receiver outwards and as far up as possible, as the water surface can strongly reflect the radio signal.
-
Page 11: Apply The Stickers
Apply the stickers: The hood is closed after connecting the batteries with adhesive tape No.531.19. It can also be installed the jumper No.21000.16 for better handling during the use of the model. waterrestistant tape No.531.19 11 / 14 2280_MP_V1... -
Page 12: Partlist
Partlist Position Name pieces number hull fiberglass No.2280.7 canopy fiberglass No.2280.8 hoods fiberglass No.2280.9 Servomount wood No.2280.10 1 Set Clevis, metal No. 3548 Threated shaft M2 x 500 mm Aluminum tube 6 x 0,5 mm rubber sealing, black No.3356 Threated rod 2- 3mm No. -
Page 13: Electric Wiring
1 to channel 1. Controller 2 on channel 6. For programming, see the instructions for the transmitter. Telemetry The enormous advantage of our Graupner Hott system is the moni- toring of all parameters by the specially developed sensors. The telemetry cable of either controller is plugged into channel 5. With it voltage, current and regulator temperature can be controlled while driving. -
Page 14: Optionparts
Optionparts: mz-12 Pro No. S1002.Pro77DE 100 A ESC No. S3030 X8-E No.S1008.DE Hood white No. 1996.7 Hood grey No. 1996.6 Power Seven No. 1996 Hood red No. 1996.5 Battery No. 78145.3 Watercooling No. 6645.1 Motor 4.300 KV No.6645 Propeller 31 mm No. 1996. 3 Propeller 29 mm No.1996.2 Battery Plug No.21000.16 MOTOREX All Clear...