Advertisement

Quick Links

 KIT INCLUDES
Full size plan.
Lasercut parts.
3.0mm W100xL600mm plywood : 3sheets
2.0mm W100xL300mm plywood : 1sheet
5.0mm W100xL565mm balsa : 1sheet
5.0mm W100xL365mm balsa : 1sheet
3.0mm W100xL600mm balsa : 1sheet
3.0mm W100xL590mm balsa : 2sheets
3.0mm W100xL465mm balsa : 1sheet
3.0mm W100xL340mm balsa : 2sheets
3.0mm W100xL330mm balsa : 1sheet
1.5mm W100xL525mm balsa : 2sheets
1.5mm W100xL465mm balsa : 2sheets
1.5mm W100xL405mm balsa : 2sheets
1.5mm W100xL230mm balsa : 1sheet
Landing gear (2.0mm Music wire 414, 395, 350mm)
Tail hardware (1.5mm Music wire 220, 72mm, PVC sleeve)
Aileron Pushrods (2ea)
CA hinge
Rubber rings for tire(2ea)
Clear Plastic
Instructions and Stickers.
Download full color instructions from
http://www.estarmodels.com [Download] menu.
INSTRUCTIONS
 ITEMS NEEDED TO COMPLETE
CAUTION
Be sure to use suitable power.
Too much power makes this plane unstable.
Brushless Motor (Max 20A/220W)
Brushless ESC 30A
Slow Propeller 1047~1147
Receiver (4ch Min.)
4 submicro Servos
Li-Poly 3s(11.1V) 1800mAh Battery
One and half rolls of covering film.
Thick nylon thread, rubber bands
EZ connectors (2ea) and Wheel Collars (4ea)
Page 1
www.estarmodels.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Fokker Eindecker and is the answer not in the manual?

Questions and answers

Summary of Contents for Estar Fokker Eindecker

  • Page 1: Items Needed To Complete

    INSTRUCTIONS www.estarmodels.com  KIT INCLUDES  ITEMS NEEDED TO COMPLETE CAUTION Be sure to use suitable power. Too much power makes this plane unstable. Full size plan. Lasercut parts. 3.0mm W100xL600mm plywood : 3sheets 2.0mm W100xL300mm plywood : 1sheet 5.0mm W100xL565mm balsa : 1sheet 5.0mm W100xL365mm balsa : 1sheet 3.0mm W100xL600mm balsa : 1sheet Brushless Motor (Max 20A/220W)
  • Page 2: Horizontal Tail

     PREPARATION  HORIZONTAL TAIL  Remove parts from laser-cut panel and group as shown above.  VERTICAL TAIL 1. Lay waxed paper or PE film over the plan. Pin the horizontal tail parts(E1-E8) on the plan and glue together with thick CA. Use scrap balsa as a supports for the edge parts.
  • Page 3: Right Wing

     RIGHT WING  LEFT WING 1. Assemble left wing as same way of right wing. 1. Glue rear spars (W10) together with thick CA. 2. Carefully sand surfaces.  AILERONS 2. Lay waxed paper or PE film over the plan. Pin fore lower spar(W9), rear lower spar(W10), trailing edge(W12) on the plan.
  • Page 4  FUSELAGE 6. Glue fore and rear left side panel. 1. Lay waxed paper or PE film over the plan. Pin the fuselage fore right side panel(F4), doublers(F5,F6A) and longerons(F1-F3) on the plan and glue together with thick CA. 7. Glue horizontal spacers(F23,F25,F27,F29,F31,F31A) with thick CA.
  • Page 5 16. Assemble and glue rear cowl parts(F40-F42) as shown above. 12. Assemble and glue motor mount(F34,F34A,F35). 17. Temporary insert wing joners(F48-F49) and left wing. 13. Assemble and glue fire wall(F36), cowling stiffners(F38) and cowling ring(F37). 18. Assemble and glue parts(F40-F42) as shown above. Caution Do not glue it in this step.
  • Page 6  WHEELS and DUMMY ENGINE 1. Glue wheels as shown(L11-L12) 21. Glue cowl in place. Impregnate wheels with thin CA glue for reinforcing. 22. Glue cockpit coarming(F52). 2. Assemble and glue crank case of dummy engine(M1-M3, M9). 23. Carefully sand fuselage surfaces. 24.
  • Page 7: Final Assembly

     PAINTING and COVERING 3. Make hinge slots and install hinges. 1. Paint cockpit coarming, cockpit inside, cowl inside, wheels, upper cabane strut, undercarriage struts, skid mounting struts, machine gun and dummy engine. Impregnate struts with thin CA glue for reinforcing. 4.
  • Page 8 7. Install rudder and elevator servos. 11. Glue dummy engine to the motor mount with M9 parts. 8. Glue the parts(W25), make aileron hinge slots and then install hinges. 12. Glue undercarriage fore(L1), rear(L2), center strut(L3). Install main landing gear, main gear axle, gear strut and tie with thread and then apply with thin CA glue.
  • Page 9: Pre-Flight Check

    19. Glue windshield, step(L10) and machine gun(F50). (Refer to windshield template on the drawing.) 15. Insert and glue wing joiner(F48-F49).  PRE-FLIGHT CHECK It must be same length with left and right. Check CG. (CG location is shown on the drawing.) Control Throws.

Table of Contents