Table of Contents
Advertisement
Quick Links
Adams Rite Manufacturing Co.
260 Santa Fe Street
Pomona, CA 91767
Phone: 800-872-3267
Fax: 800-232-7329
www.adamsrite.com
®
eForce
Owner's
Manual &
Installation
Instructions
For Models
3090C & 3090P
Adams Rite Manufacturing Co.
260 Santa Fe Street
Pomona, CA 91767
Phone: 800-872-3267
www.adamsrite.com
Keyless Entry
Advertisement
Table of Contents
Related Manuals for ADAMS RITE eForce 3090C
Summary of Contents for ADAMS RITE eForce 3090C
- Page 1 Keyless Entry Owner’s Manual & Installation Instructions For Models 3090C & 3090P Adams Rite Manufacturing Co. 260 Santa Fe Street Pomona, CA 91767 Adams Rite Manufacturing Co. Phone: 800-872-3267 260 Santa Fe Street Fax: 800-232-7329 Pomona, CA 91767 www.adamsrite.com Phone: 800-872-3267 www.adamsrite.com...
- Page 2 (in material or workmanship) occur in its products, ADAMS RITE, upon prompt notification and proof to its satisfaction that the product was defective in manufacture for the use intended by ADAMS RITE, will at its option, ex- change the product, repair the defect or refund the price charged by ADAMS RITE, FOB factory based on the following schedule: All mechanical products for five (5) years from the date of manufacture;...
-
Page 3: Table Of Contents
Table of Contents Table of Contents General Information ................4 Definitions ..................4 FCC Statement .................. 5 IC Statement ..................5 Operational Description ..............6 Operational Specifications ..............7 Troubleshooting ................. 8 Installation Tools & Equipment ............9 Door Preparation ................10 Spindle Preparation ................. -
Page 4: General Information
The eForce Prox or eForce iCLASS will mechanically interface with: Adams Rite MS Series Deadbolts; Adams Rite 4500/4900 Deadlatches; Adams Rite 8000 Series Exit Devices; Yale 7200 Series Narrow Stile Exit Devices; Cor- bin Russwin ED4000 Series, and SARGENT 8500 Narrow . -
Page 5: Fcc Statement
® Mounting the eForce FCC S TATEMENT This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are Insert the properly dimensioned designed to provide reasonable protection against harmful interference in a spindle from Step 2 into the output residential installation. -
Page 6: Operational Description
STEP 5 MORTISE CYLINDER INSTALLATION PERATIONAL ESCRIPTION Manual Operation – Key Cylinder Using a Philips Head Screwdriver, remove the eight (8) #10-32 x 5/8” Insert key into lock cylinder. ® screws on the back of the eForce Turn the key 180° to the detent position and hold. and gently lift the back plate off the Rotate the lever until latch or deadbolt clear the strike and open the door. -
Page 7: Operational Specifications
® PERATIONAL PECIFICATIONS STEP 4 HANDING THE eForce Prox & iClass Card Compatibility: ® The eForce is shipped in a non- Prox: All HID (125kHz) Prox credentials handed neutral position with the ac- iCLASS: All iCLASS (13.56MHz) credentials cess cover off as shown. Electrical Specifications (Prox/iCLASS): Power Requirements Voltage In: 12Vdc (Range: 10.8Vdc –... -
Page 8: Troubleshooting
RIM Exit Device Application: 3090P-01 & 3090C-01 for 8700/8800 ROUBLESHOOTING Green light comes on, but lever will not retract latch or deadbolt: On the back side of the exit device, remove ® Check the eForce body connection with lock/latch mechanism. only the lower Phillips head screw, depending Check the spindle length (see installation instructions). -
Page 9: Installation Tools & Equipment
Yale 7200 Series Narrow Stile Exit Devices; Corbin Russwin ED4000 Series, and SARGENT 8500 Narrow Design Rim Exit Devices. ® The 3090P-02 & 3090C-02 are compatible with Adams Rite MS Series Deadbolts only! T HESE UNITS ARE NOT INTERCHANGEABLE These instructions, and the fasteners supplied, apply to metal door applications. -
Page 10: Door Preparation
Insert Flat end into exit devices For Adams Rite 8000 Series Surface Vertical Rod & Rim Exit Devices, Yale 7200 Series Narrow Stile Exit Devices, Corbin Russwin ED4000 Series, and SARGENT 8500 Narrow Design Rim Exit Devices: Snap-off spindle at fourteenth (14th) notch as shown in F .
Need help?
Do you have a question about the eForce 3090C and is the answer not in the manual?
Questions and answers