Advertisement
Wire Free Portable Door Chime Kit with Ultra Bright Light & Converter-SX-34
positions marked in diagrams below.
4. Snap the front cover of converter back on, then it is
ready to use.
Important: Do not connect the Converter unit with any
Lighted Bell Push.
Please note that these diagrams are only for
reference as a guide.
EACH Wired chime can be wired differently, so if you
encounter problems, PLEASE CALL THE HELPLINE NO. 0121 5449499
Converter
unit
SX
Chime
1
unit
B and C
Converter
unit
SX
Chime
3
unit
A and C
WIRED
CHIME
(Transformer
operation)
T
Sound Volume Adjustment
Melody sound volume can be adjusted to high
or low, the high-low switch is located at the side
of the door chime unit.
Flashing Light Function
If the flashing ultra light is not required, simply
switch the function off. The on/off switch is
located inside the door chimes battery compartment.
Important
1. Do not mount the Converter unit onto any metal surface or UPVC doorframe, as this will
reduce the operation range seriously.
2. Do not expose the unit directly to rain or immerse either in water.
Converter
unit
B+C SWITCH
A+C 8V/AC
Wired Bell
Push
B+C SWITCH
Converter
unit
SX
Chime
2
unit
A and C
WIRED
CHIME
(Battery
operation)
Converter
unit
SX
Chime
4
unit
A and C
WIRED
T
CHIME
(Transformer
operation)
"AA"
LR6
"AA"
LR6
3. Do not mount the Converter close to fireplace or expose to high temperature.
4. Do not drop the Converter or subject to excessive blows.
5. The Converter and Door Chime units are designed for indoor use only.
6. Always use alkaline batteries as these will give longer service and are less likely to leak.
7. Please dispose of old, defective batteries in an environmentally friendly manner in
accordance with the relevant legislation.
8. Make sure that no naked flame sources, such as lighted candles, should be placed on the
unit.
9. The unit should not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the unit.
10. CAUTION: Replace only with the same or equivalent type of battery that are
recommended by the manufacturer.
11. CAUTION: Danger of explosion if battery is incorrectly installed or replaced.
Trouble Shooting & User Hints
Problem
Possible Causes
Chime does not
1. Units are out of range (max.
sound but LED
range 100m)
lights on the
2. Converter and chime units are
converter
not on same channel
3. Converter not wired correctly
Chime does not
1. Flat Converter battery
sound plus no
2. Wrong polarity of battery in
lights on Push
converter
Button LED
Chime sounds
A similar wirefree door chime
product is operating nearby
without converter
being pressed
on the same frequency digital
code
NOTE: There are no serviceable parts in the unit, do not attempt to repair it.
Specification
A. Converter
Power
: 1 x 23A battery (included, replace with Byron model SD-100)
: 3.0mA - ON
Consumption
0.003mA - OFF
B. Door Chime unit
: 2 x 1.5volt batteries ("AA", R6 or UM3 - not included)
Power
Alternatively powered by A/C-D/C 9volt 300mA
adaptor (Byron model SX-36 - not included)
: 100mA - ON
Consumption
0.3mA - Stand-by
Operating Temperature
: -10°C to +40°C
: 100 metres (320 feet approx.) in open field
Operating Distance
Selectable Tone
: Total eight (8) tones available
Selectable digital code
: Total sixteen (16) possible digital codes
Suggested Remedy
1. Operate the Chime unit within the
operation range (100m)
2. Re-set the digital code (see Digital
Code Set Up)
3. See wiring diagrams opposite
1. Change the battery
2. Re-insert battery as internal
marking in right polarity
Reset the digital code
(see Digital Code Set Up)
Advertisement
