Motorola Motostart H700 Manual page 2

TURNING ON AND OFF
To turn your headset on, open the
headset boom. The indicator light flashes
blue.
H700
Bluetooth®
To turn your headset off, close the
headset boom. The indicator light will turn
Handsfree Headset
off.
To conserve battery power, turn off your
headset when you don't plan to use it for
a while.
IMPORTANT: IMPORTANT:
Be sure to first follow the Be sure to first follow the
Quick Start Guide Quick Start Guide
on the reverse side to on the reverse side to
complete initial setup of complete initial setup of
your H700. your H700.
Function
Make a voice dial call
End a call
Receive a call
Reject a call
Redial last call
Note: Your H700 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
WEARING THE
1 Open the headset boom, then open the
earhook (45° from the headset).
2
Loop the earhook over your ear.
3
Press the headset to your ear.
4 Point the headset boom towards your
mouth.
Multi-Color
Indicator Light
MAKING CALLS MAKING CALLS
Function
Action
Tap the Call button Answer a second
incoming call
and speak the
name after the tone
Tap the Call button Toggle between two
or close headset active calls
boom
Join a 3-way call
(Note: Feature is phone/
Open headset boom
or tap the Call button network dependent.)
(if boom is already
Put an active call on
open)
hold or resume a call
Press and hold the on hold
Call button until you
Transfer a call from the
hear a beep
phone to the headset
Press and hold the
Disable or enable the
Call button until you
indicator light
hear a beep
Mute or unmute a call
CHANGING FOR USE
ON OTHER EAR
HEADSET
You can wear your H700 headset on your left or
right ear. The headset comes ready for the right
ear. To change the headset for the left ear:
1 Open the headset boom,
then open the earhook
(90° from the headset).
2
Gently lift and pull the
top of the earhook up
and off the upper hinge
pin. Then, pull it away to
remove it.
3
Flip the headset over.
4 Hook the bottom of the
earhook onto the lower
hinge pin, then lift and
pull the top of the
earhook over the upper
hinge pin.
INDICATOR LIGHTS
CONTINUED
With the Charger Plugged In
Action
Indicator Light
Press and hold the
Red (steady)
Call button (places
first call on hold)
Yellow (steady)
Press and hold
the Call button
Green (steady)
Press and hold
both Volume buttons With No Charger Plugged In
Indicator Light
Press and hold the
Off
Call button until you
Magenta (steady)
hear a beep
Red
Tap the Call button
Blue (10 rapid flashes)
Press and hold
Blue (slow pulse)
both Volume
buttons for 3 to 4
seconds
Blue (quick flash)
Tap both Volume
Note: After 5 minutes of inactivity, the light stops flashing to
buttons
conserve power, but the headset remains in standby mode.
CHANGING VOLUME
BUTTON ORIENTATION
You can also change the orientation of the
volume buttons on your headset.
1 Turn the headset power off.
2
Press the Call E button until the
indicator light becomes steadily lit in
magenta, then press the Volume button
you want to assign as the "volume up"
button.
1 Open Earhook
2 Pull Earhook Up
Volume
Buttons
Hinge Pin
AUDIO TONES
The audio tones provide information about your
headset status.
Headset Status
Charging (less the
Audio Tone Headset Status
80% charged)
Single high tone when Volume at minimum
Charging (more than
pressing volume button or maximum
80% charged)
Five rapid high tones Low battery
Charging complete
repeated every 60 sec.
No audio indications; Out of range
deteriorating quality
Headset Status
Ring tone Incoming call
Power off
Single high tone Pairing confirmation
Pairing mode
Single low tone Voice activation
Battery low
Dual high/low tone Voice tag not
Pairing
recognized
successful
Single high tone End call
Connected
Low to high tone Phone network
(on a call)
not available
Standby (not on call)
Two ascending tones Mute enabled
Two descending tones Mute enabled
Call
Button