Advertisement
3. Remote control setup: Brand Search
The Nova remote control can be programmed to operate your TV set or
another device, for example a DVD player. The Nova does this by registering a
5-digit brand code that is specific to the device.
1. Note the brand of your device, then find its 5-digit brand code by referring
to the brand code tables on the Amino support site (www.aminocom.com/
support). Make a note of the 5-digit brand code.
2. Make sure your device is turned on.
3. On the remote control, press the device control button (3) for the device
you want to control, for example if you want to control a DVD player, press DVD.
4. Press and hold the Setup button (14) for approximately three seconds until
the device control button flashes twice.
5. Enter the 5-digit brand code for your device. On each digit entry the device
control button will flash. If you make an error, the LED will give a single long
flash.
6. Press the Power on button (1). If your device turns off then setup is complete.
7. If your device does not turn off, repeat the setup procedure using another
code (if listed) for the device. You may need to try several codes.
If you change your device to a different brand and the remote control requires
re-programming, repeat this brand search procedure with your new device.
If your device is not listed, or you have tried all the codes listed for it and it still
does not respond to the remote control, your device may still be supported and
you should try the Auto Search method.
4. Remote control setup: Auto Search
If your device cannot be found by the previous brand search method and you
have tried all the codes listed for that device, then Auto Search can be used.
1. Make sure your device is turned on.
6. Resetting the remote control
Resetting Brand Search or Auto Search
1. Press and hold the Setup button for approximately three seconds until the
device control button flashes twice.
2. Press the number buttons 9 7 7
3. Press and hold the Setup button for approximately three seconds until the
device control button flashes twice.
4. If you make an error, the LED will give a single long flash.
Resetting 'punch through'
1. Press and hold the Setup button for approximately three seconds until the
device control button flashes twice.
2. Press the number buttons 9 7 8
3. Press and hold the Setup button for approximately three seconds until the
device control button flashes twice.
4. If you make an error, the LED will give a single long flash.
FCC statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
2. On the remote control, press the device control button for your device.
3. Press and hold the Setup button for approximately three seconds until the
device control button flashes twice.
4. Press the number buttons 9 9 1 then press the Power button.
5. Press the CH+ button repeatedly until your device turns off.
6. Press and hold the Setup button until the device control button flashes twice.
The brand code is now saved.
5. Key 'punch through' setup
When you have configured the Nova remote control to work with a selected
device, the remote control buttons will operate that device. However,
specific buttons can be sent to another device by using the 'punch through'
feature: for example you may want to send the volume up and down buttons
to an AUX device rather than to your TV set.
1. Press and hold the Setup button for approximately three seconds until the
device control button flashes twice.
2. Press the number buttons 9 7 8
3. Press the device control button for the device you want to control, for
example if you want to control a DVD player, press DVD.
4. Press the keys you want to punch through, for example Volume up and
down, Mute.
5. Press the device control button for the device(s) you want to target, for
example STB, DVD.
6. Press and hold the Setup button for approximately three seconds until
the device control button flashes twice. The 'punch through' setup is now
complete.
7. If you make an error, the LED will give a single long flash.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment. This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including interference that
may cause undesired operation of the device.
IMPORTANT NOTE:
RF exposure warning statement:
1) This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
2) This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20 centimetres between the radiator and your body.
Operation of this device is restricted to indoor use only.
Industry Canada statement
This device complies with ISED's licence-exempt RSSs. Operation is subject to the
following two conditions:
1) This device may not cause harmful interference, and
2) this device must accept any interference received, including interference that
may cause undesired operation.
Le présent appareil est conforme aux CNR d' ISED applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
1) le dispositif ne doit pas produire de brouillage préjudiciable, et
2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage
susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED
établies pour un environnement non contrôlé. Cet équipement doit être installé et
utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et
votre corps.
99-709851-04 Rev.01-00
AM-011191-DS v1
Advertisement
