Advertisement
Quick Links
HC308
Ultra-Fast Fill Quick Coupler
Instruction Manual
Failure to follow these instructions or to properly install and maintain this equipment could result in gas leak-
age, fire or explosion causing property damage and personal injury or death.
Oasis products must be installed, operated and maintained by trained and competent personnel in
accordance with all applicable local codes, rules and regulations in addition to the Oasis Instructions.
Oasis Engineering Ltd. will not be held liable in such circumstances where installation, operation and
maintenance procedures were performed by incompetent personnel resulting in improper assembly, unsafe
operation, equipment damage or personal injury.
Oasis Engineering Ltd
129 Birch Avenue, Tauranga, New Zealand.
T: +64 7 928 3808 F: +64 7 928 3809
E: info@oasisNGV.com
W: www.OasisNGV.com
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Oasis HC308
Summary of Contents for Oasis HC308
- Page 1 Oasis products must be installed, operated and maintained by trained and competent personnel in accordance with all applicable local codes, rules and regulations in addition to the Oasis Instructions. Oasis Engineering Ltd. will not be held liable in such circumstances where installation, operation and maintenance procedures were performed by incompetent personnel resulting in improper assembly, unsafe operation, equipment damage or personal injury.
- Page 2 High pressure gas and gas equipment can cause serious harm to both infrastructure and personnel if safety precautions are not followed. Oasis recommends considering the use of the following PPE when working with high pressure along with any other site specific health and safety requirements:...
-
Page 3: Installation Instructions
Ensure it does not cross thread. Check for leaks on first use with snoop or soapy water. HC308-INS-02 4717 © Oasis Engineering Limited We reserve the right to modify product specifications without prior notice. -
Page 4: Connection Instructions
Oasis recommends the use of the following PPE when operating coupler. Stand clear of coupler when in use. HC308-INS-02 4717 © Oasis Engineering Limited We reserve the right to modify product specifications without prior notice. - Page 5 6. Return female fitting to a holder and Fitting. always keep off the ground. CLICK SHC308-18 — Plastic Dummy Male Mount available separately HC308-INS-02 4717 © Oasis Engineering Limited We reserve the right to modify product specifications without prior notice.
- Page 6 (For all O-rings) Silicone Grease 243 Loctite Rocol MX22 or similar medium strength (For all O-rings) The Complete Oasis Seal Kit must be used Tools Required Anti Seize Grease Pick Tool Cleaner (Warm Soapy (Loctite 771 or Similar) Part Number:...
- Page 7 1. Clamp female coupler in vice. retainer. 3. Remove the poppet retainer using the 4. Lift out the poppet retainer and put aside. assembly tool. HC308-INS-02 4717 © Oasis Engineering Limited We reserve the right to modify product specifications without prior notice.
- Page 8 6. Pick out the O-ring and backup and discard. 8. Position the assembly tool over the poppet 7. Clamp the male couple in the vice. retainer. HC308-INS-02 4717 © Oasis Engineering Limited We reserve the right to modify product specifications without prior notice.
- Page 9 10. Remove the poppet retainer using the assembly tool. assembly tool. 11. Discard the poppet and spring. 12. Clean all of the components and Visually Inspect parts for damage. HC308-INS-02 4717 © Oasis Engineering Limited We reserve the right to modify product specifications without prior notice.
- Page 10 3. Torque the poppet retainer into the body. 4. Insert the O-ring and back-up. Backup O-ring Recommended Torque : 40Nm HC308-INS-02 4717 © Oasis Engineering Limited We reserve the right to modify product specifications without prior notice.
- Page 11 7. With the poppet screwed hand tight into body. Be careful not to cross thread the location apply Loctite to the poppet retainer retainer. thread HC308-INS-02 4717 © Oasis Engineering Limited We reserve the right to modify product specifications without prior notice.
- Page 12 10. Coupler servicing complete. Ensure male and female fittings couple successfully and refer to installation instructions for refitting of the device and dust cap. It is recommended the product is checked for leaks on first use. HC308-INS-02 4717 © Oasis Engineering Limited We reserve the right to modify product specifications without prior notice.
Need help?
Do you have a question about the HC308 and is the answer not in the manual?
Questions and answers