Sunfire Dynamic SDSWiTX Quick Start Manual

Introduction
Thank you for purchasing a Sunfire Dynamic
Series Wireless SDSWiTX Transmitter or
SDSWiRX Receiver.
This wireless system allows an SDS series
subwoofer to be added to a system, without the
need to run long cables the subwoofer.
The SDSWiTX transmitter receives the
line-level subwoofer/LFE signal from the
Home Theater or stereo system's preampli-
fier or receiver. It then transmits it digitally to
the SDS WiRX receiver located close to the
subwoofer.
Contents
• One SDSWiTX Transmitter
or
• One SDSWiRX Receiver
• One detachable AC/DC power adapter
• One short patch RCA cord
Unpacking
Your Sunfire product should reach you in
perfect condition. If you do notice any shipping
damage, please contact your Sunfire Dealer
immediately.
Gently lift out the unit and all accessories, and
remove all the packing material. It is important
to save all the packing materials and the box
in case your unit ever needs to be moved or
shipped for repair.
Make sure that you keep your sales receipt. It
is the only way to establish the duration of your
Limited Warranty and it may come in useful for
insurance purposes.
Care
To clean the unit, first unplug the AC adapter's
power cord and then use a soft dry cloth to
clean the surfaces.
Wireless Receiver
and Transmitter
SDSWiTX and SDSWiRX

Quick Start Guide

Specifications
Wireless Band
2.4 GHz
Sampling Rate
48 kHz
Resolution
16 bit
Latency
22 ms
Indoor Range
One Tx and One Rx: 40 feet
One Tx and Two Rx: 25 feet
One Tx and Three Rx: 17 feet
One Tx and Four Rx: 10 feet
Power Supply
5V dc, 0.5A (AC/DC adapter supplied)
Receivers
Each transmitter can control up to 4 receivers
Audio Input/Output
Line-Level RCA connector.
Dimensions L x W x H
8.1 x 5.5 x 2.6 in
206 x 140 x 66 mm
Weight
SDSWiRX 10.8 oz (305g)
SDSTiRX 11.4 oz (324g)
Service
If your Sunfire product ever requires service,
please write to us or call:
Sunfire,
1300 E New Circle Road, Suite 150
Lexington, KY 40505
Phone 859-514-8290
Fax: 859-269-7972
Warranty
Sunfire, a division of Elan Home Systems,
LLC, is proud of its products which have been
built with care using advanced technology and
premium component parts. Your unit has been
crafted to perform properly for many years. The
warranty details for your product are shown on
the Sunfire website www.sunfire.com

Important Safety Instructions

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Install in accordance with the manufacturer's
instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce
heat.
9. Only use attachments/accessories specified
by the manufacturer.
10. Unplug this apparatus during Iightning storms
or when unused for long periods of time.
11. Refer all servicing to qualified service person
nel. Servicing is required when the appa- -
ratus has been damaged in any way such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
FCC and IC Information
This equipment complies with Part 15 of FCC RF
Rules. Operation is subject to the following two
conditions:
1. This device may not cause interference and
2. This device must accept any interference, in -
cluding interference that may cause undesired
operation of the device.
This Device complies with RSS-210 of the IC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause interference and
2. This device must accept any interference
received, including interference that may cause
undesired operation.
Warning: Changes or modifications to this unit
not expressly approved by the party respon -
sible for compliance could void the user's
authority to operate the equipment.
To find out more about this and other Sunfire products,
please visit our website: www.sunfire.com
Features
Transmitter
1 2 3
5 6
1. LINK Button (Tx)
This button is used in the intial set-
ting-up, to establish a link between
the transmitter and one or more
receivers.
2. Transmit LED (Tx)
Turns on when transmitting signals
to the receiver(s).
3. Power LED
Turns on when the supplied AC/DC
adapter is connected.
4. Receive LED (Rx)
Turns on when receiving signals
from the transmitter.
12. NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to pro
vide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instruc
tions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or televi
sion reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
- • Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and the receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
FCC and IC Radiation Exposure Statement
This equipment complies with FCC radiation ex-
posure limits set forth for an uncontrolled environ-
ment and meets the exemption from the routine
evaluation limits in section 2.5 of RSS 102.
1. This Transmitter must not be co-located or
operating in conjunction with any other antenna
or transmitter.
2. This equipment complies with FCC RF radia-
tion exposure limits set forth for an uncon-
trolled environment. This equipment should be
installed and operated with a minimum distance
of 20 centimeters from user and bystanders.
Warning: The device meets the exemption from
the routine evaluation limits in section 2.5 of
RSS 102, and users can obtain Canadian infor-
mation on RF exposure and compliance from
the Canadian Representative Product Solutions
Group at Tel: (519) 763-4538.
Receiver
4 3
7
5. Subwoofer LFE Input (Tx)
This line-level RCA input connects
to the subwoofer/LFE output of a
home theater or stereo system's
subwoofer/LFE output. A short RCA
cable is supplied.
6. Power Input
Connect to the DC output of the
supplied AD/DC adapter.
The voltage input is + 5V dc on the
pin, at 0.5A
7. Subwoofer LFE Output (Rx)
This line-level RCA output con-
nects to the subwoofer/LFE input of
a Sunfire SDS subwoofer. A short
RCA cable is supplied.
6