Advertisement
Advertisement
Table of Contents
Related Manuals for Ericsson AP 6120
Summary of Contents for Ericsson AP 6120
- Page 1 AP 6120 Quick Install Guide QUICK GUIDE 1/006 92-LZA 101 810 Uen A...
- Page 2 Copyright © Ericsson AB 2013. All rights reserved. No part of this document may be reproduced in any form without the written permission of the copyright owner. Disclaimer The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing.
-
Page 3: Getting Started
Getting Started Getting Started Package Contents Note: AC Power adapter ordered and shipped separately. Unit Description 1.2.1 Power Connector The unit does not have a power switch. It is powered on when connected to a power source. The power adapter, ordered and shipped separately, automatically adjusts to any voltage between 100~240 volts at 50 or 60 Hz. - Page 4 The AC Power Adapter relies on the rated fuse or circuit breaker of the wall outlet (15 A in North America, 10 A in Europe). Caution! Use ONLY the Ericsson power adapter for the AP 6120. Use of any other power adapter may damage the unit and voids Ericsson’s product warranty. 1.2.2 Internet Port The unit can be powered with IEEE 802.3af or IEEE 802.3at Power over...
- Page 5 If you hold down the button for 15 seconds or more, until all of the LEDs turn off, any configuration changes you may have made are removed, and the factory default configuration is restored to the AP 6120. 1/006 92-LZA 101 810 Uen A | 2013-04-11...
-
Page 6: Step 1-Select Location
AP 6120 Quick Install Guide Installing the AP 6120 Step 1—Select Location Choose a proper place for the unit. In general, the best location is at the center of your wireless coverage area, within line of sight of all wireless devices. For optimum performance, consider these guidelines: •... - Page 7 Installing the AP 6120 Warning! To comply with FCC radio frequency (RF) exposure limits (FCC OET 65C) for the general population, antennas must be located at a minimum distance of 7.9 inches (approx. 20 cm) or more from the body of all persons.
- Page 8 AP 6120 Quick Install Guide Step 3—Connect and Power On The AP 6120 can get its operating power directly from an AC wall outlet or from the Internet port when connected to a device that provides IEEE 802.3af or 802.3at compliant Power over Ethernet (PoE). If the AP 6120 is connected to both a PoE source device and an AC power source, AC is disabled.
-
Page 9: Step 4-Check Leds
Installing the AP 6120 Figure 2 Power over Ethernet Warning! If PoE is used, the AP 6120 must be connected to a power source that complies to IEEE 802.3af or 802.2at, or to an IEC/EN 60950-1 compliant power limited source. Step 4—Check LEDs After powering on, wait 2 minutes and check that the unit’s LED match those in... -
Page 10: Step 5-Configure Unit
AP 6120 Quick Install Guide Step 5—Configure Unit You can configure the AP 6120 through its Web interface or Command Line Interface (CLI). Refer to the Access Point User Guide, 1/1553-LZA 101 806, for complete details. 1/006 92-LZA 101 810 Uen A | 2013-04-11... - Page 11 Installing the AP 6120 1/006 92-LZA 101 810 Uen A | 2013-04-11...
- Page 12 AP 6120 Quick Install Guide © Ericsson AB 2013. All rights reserved. No part of this document may be reproduced in any form without the written permission of the copyright owner. The contents of this document are subject to revision without notice due to continued progress in methodology, design and Ericsson Inc.