Subscribe to Our Youtube Channel
Related Manuals for SASFORKS Male Master
Summary of Contents for SASFORKS Male Master
- Page 1 OPERATOR MANUAL AND SERVICE GUIDE FOR SAS™ MALE MASTER / QUICK COUPLER SYSTEM O:\PROCEDURES\Forks\OPERATOR MANUALS\Male Master QC Operator Manual\00-Cover.doc www.sasforks.com © 2014, 2004, 1987 S.A.S. of Luxemburg, Ltd. 1-877-SAS-FORK...
- Page 2 Fax: 1-920-845-2309 S.A.S. OF LUXEMBURG, LTD. E1039 Hwy 54 • PO Box 260 E-Mail: sales@sasforks.com Web site: www.sasforks.com LUXEMBURG, WI 54217 O:\PROCEDURES\Forks\OPERATOR MANUALS\Male Master QC Operator Manual\01-Fork Management.doc www.sasforks.com © 2014, 2004, 1987 S.A.S. of Luxemburg, Ltd. 1-877-SAS-FORK Page 1...
-
Page 3: Pinch Points
Align pin holes, sleeves and insert pins. Properly secure pins in place PINCH POINTS When Male Master is in use avoid possible pinch points to prevent serious injury. Keep hands and loose clothing clear at all times. O:\PROCEDURES\Forks\OPERATOR MANUALS\Male Master QC Operator Manual\02-Initial Shipping Receipt.doc www.sasforks.com... - Page 4 HYDRAULIC PRESSURE REQUIREMENTS SAS Male Master Hydraulic Quick Coupler operates at a maximum of 5,000 PSI. Most machines operate below this pressure it is recommended that machine pressure is checked and set prior to operating unit. Failure to do so can cause catastrophic failure of cylinder, fittings and/or hoses.
- Page 5 TO PUMP S.A.S. of Luxemburg, Ltd. Center Drive Hwy 54 PO Box 260, Luxemburg, WI 54217 USA Phone: 920-845-2198 1-877-SAS-FORK Fax: 920-845-2309 Email: sales@sasforks.com Web: www.sasforks.com © 2010 S.A.S. of Luxemburg, Ltd. Sales on “Sassvr02”/ADMINISTRATION/A-Product Sheets/Product Brochures/24V PUMP LIT INSTRUCTIONS...
- Page 6 Locking pin must be sure to be fully locked / engaged so the attachment doesn’t fall off. Male Master Quick Coupler PIN recessed, unlocked position. Male Master Quick Coupler PIN fully engaged in attachment O:\PROCEDURES\Forks\OPERATOR MANUALS\Male Master QC Operator Manual\05-Daily Pre-Operation Inspection and Greasing.doc www.sasforks.com © 2014, 2004, 1987 S.A.S. of Luxemburg, Ltd.
- Page 7 O:\PROCEDURES\Forks\OPERATOR MANUALS\ Master QC Operator Male Manual\06-Wheel Loader Daily Inspection Sheet 06-06.doc www.sasforks.com Page 6...
- Page 8 •Never operate equipment without correct tire pressure in all tires. A soft tire could cause the unit to tip over •Always park equipment with the forks lowered flat to ground, & grapple lowered to resting closed position. O:\PROCEDURES\Forks\OPERATOR MANUALS\Male Master QC Operator Manual\07-General Operating Precautions.doc www.sasforks.com ©...
- Page 9 SAS will approve an appropriate amount of hours and cost for the repair before authorizing repairs to begin. No provisions will be made for incidental damages, mileage, travel time, overtime, downtime, or special freight charges. O:\PROCEDURES\Forks\OPERATOR MANUALS\Male Master QC Operator Manual\08-Safety Warranty pg1.doc www.sasforks.com ©...
-
Page 10: Blade Wear
SEVERABILITY: Any legally unenforceable provision may be severed from this agreement, and the remaining terms and conditions will be enforced as a whole. O:\PROCEDURES\Forks\OPERATOR MANUALS\Male Master QC Operator Manual\09-Safety Warranty pg2.doc www.sasforks.com © 2004, 1987 S.A.S. of Luxemburg, Ltd. - Page 11 Page 10...
- Page 12 M-3551 Ref. Ref. Part No. Part No. Req. Description Description 1 2 3 03404 BOX ASSEMBLY, Push Button • STRAIN RELIEF, 1 2 3 03404 BOX ASSEMBLY, Push Button • STRAIN RELIEF, 1 1 2 Page 12 4 5 6 01418 (Plastic) •...
- Page 13 EURO-VOLVO L45-L120 TYPE INTERFACE ==PARTS LIST==...
- Page 14 IT38 STYLE INTERFACE QUICK COUPLER 8/14/2017 PARTS LIST FOR SERIAL NUMBER: SAS F5469 G-BULKHEAD FITTING F-HOSE FITTING E-HOSE FITTING L-HOSE J-GUIDE SLOT STOP BOLT D-CYLINDER FITTINGS K-GUIDE SLOT STOP NUT A-CYLINDER H-CONNECTOR B-PINS I-NYLON LOCK NUT C-COVER M,N,O-BOLT, WASHERS ITEM DESCRIPTION S/N: SAS F5469 PART # QTY.
- Page 15 Scribe contour of bucket pro- file into rib. Remove from bucket and cut with plasma or torch. Install contoured coupler hooks into male master on machine and position against back of bucket. Tack to bucket and unhook from male master ( machine side ).
Need help?
Do you have a question about the Male Master and is the answer not in the manual?
Questions and answers