Subscribe to Our Youtube Channel
Related Manuals for SASFORKS Crushing Forks
Summary of Contents for SASFORKS Crushing Forks
- Page 1 SAS CRUSHING FORKS™ w/CLAW ENGINE PICKER OPERATOR MANUAL Operations/Procedures/forks/ Engine Puller Claw Operator Manual//00-COVER.doc 4/16/08 www.sasforks.com © 2004, 1987 S.A.S. of Luxemburg, Ltd. 1-877-SAS-FORK...
-
Page 2: Table Of Contents
The SAS FORKS™, this operator manual, www.sasforks.com likeness of such, are property of S.A.S. of Luxemburg, Ltd. and are protected under all applicable Copyright, Trade Mark, Trade Dress, and Pending Patent. No information, pictures, designs, or forks may be duplicated in part, entirety, or in likeness. -
Page 3: Letter To Owners, Managers, And Operators
S.A.S. OF LUXEMBURG, LTD. Adam Lindley, Sales Manager 133 Center Drive Hwy 54 • PO Box 260 E-Mail: sales@sasforks.com Web site: www.sasforks.com LUXEMBURG, WI 54217 Operations/Procedures/forks/ Engine Puller Claw Operator Manual//02-FORK MANAGEMENT.doc 4/16/08 www.sasforks.co © 2004, 1987 S.A.S. of Luxemburg, Ltd. -
Page 4: Pre-Operation Inspection
Please see page 4 for details. Replace if less than 1/8” thick. Order replacement skid plates by calling: U.S.A. Phone: 920-845-2198 or 1-877-SAS-FORK. 5) CHECK ROCKER PANEL BUMPER PADS ON THE SAS CRUSHING FORKS.™ IF SO EQUIPPED. Replace if severely cracked, torn or missing. -
Page 5: Skid Plate Inspection
Phone: 1-877-SAS-FORK (1-877-727-3675) or 920-845-2198 Fax: 1-920-845-2309 Email: sales@sasforks.com SKID PLATE DIAGRAM WITH INSTALLATION INSTRUCTIONS NOTE: DO NOT WELD ALONG FRONT AND BACK OF SKID PLATES. ONLY SKIP WELD ALONG OUTSIDE EDGES. Operations/Procedures/forks/ Engine Puller Claw Operator Manual//04-SKID PLATE INSPECTION.doc 4/16/08 www.sasforks.com... -
Page 6: Operating Guidelines
The forks were designed, tested, and use- proven to give you the fastest and easiest entry possible using this method. Operations/Procedures/forks/ Engine Puller Claw Operator Manual//05-OPERATION GUIDELINES PG2.doc 4/16/08 www.sasforks.com © 2004, 1987 S.A.S. of Luxemburg, Ltd. 1-877-SAS-FORK Page 5... -
Page 7: Operating Guidelines Pg
You may run into other vehicles, a building, or people and not be able to stop. Drive very slowly in this type of weather. Operations/Procedures/forks/ Engine Puller Claw Operator Manual//06-OPERATION GUIDELINES PG3.doc 4/16/08 www.sasforks.com 1-877-SAS-FORK © 2004, 1987 S.A.S. of Luxemburg, Ltd... -
Page 8: Operating Precautions
30 feet away for safety reasons. Operations/Procedures/forks/ Engine Puller Claw Operator Manual//07-PRECAUTIONS.doc 4/16/08 www.sasforks.com 1-877-SAS-FORK © 2004, 1987 S.A.S. of Luxemburg, Ltd. -
Page 9: Safety Information
10)Never operate your machine with the automatic dump feature engaged or with the detent in the raise position. Operations/Procedures/forks/ Engine Puller Claw Operator Manual//08-FORK SAFETY INFORMATION.doc 4/16/08 www.sasforks.com 1-877-SAS-FORK © 2004, 1987 S.A.S. of Luxemburg, Ltd. Page 8... -
Page 10: General Operating Procedure
Follow procedures and information in the Operator Manual for Machines Equipped with SAS FORKS™ WHEN FINISHED USING THE MACHINE: a. Lower the forks to the ground Operations/Procedures/forks/ Engine Puller Claw Operator Manual//09-GENERAL.doc 4/16/08 www.sasforks.com 1-877-SAS-FORK © 2004, 1987 S.A.S. of Luxemburg, Ltd. Page 9... - Page 11 Operations/Procedures/forks/ Engine Puller Claw Operator Manual//10-WHEEL LOADER DAILY INSPECTION SHEET.doc 4/16/08 www.sasforks.com © 2004, 1987 S.A.S. of Luxemburg, Ltd. 1-877-SAS-FORK Page 10...
- Page 12 SAS will approve an appropriate amount of hours and cost for the repair before authorizing repairs to begin. No provisions will be made for incidental damages, mileage, travel time, overtime, downtime, or special freight charges. Operations/Procedures/forks/ Engine Puller Claw Operator Manual//11-SAFETY WARRANTY PG1.doc 4/16/08 www.sasforks.com 1-877-SAS-FORK © 2004, 1987 S.A.S. of Luxemburg, Ltd.
- Page 13 SEVERABILITY: Any legally unenforceable provision may be severed from this agreement, and the remaining terms and conditions will be enforced as a whole. Operations/Procedures/forks/ Engine Puller Claw Operator Manual//12-SAFETY WARRANTY PG2.doc 4/16/08 www.sasforks.com 1-877-SAS-FORK © 2004, 1987 S.A.S. of Luxemburg, Ltd.
- Page 14 PRE-HEAT PROCEDURE: WRAP/BACKFILL WELD TECHNIQUE: THE PREHEAT TEMPERATURE SHOULD BE ABOVE 600 F & NOT TO EXCEED 850 F, TO AVOID THIS: • ON WELD AREA "A" ONLY! • USE A SOFT FLAME AND DO NOT LEAVE UNATTENED • USE A 600 F TEMP STICK FREQUENTLY ON HEATED SURFACE UNTIL IT MELTS WELD PROCEDURE: •...
- Page 15 F~RETRACT-RIGHT N~UPPER CYLINDER PIN ASSEMBLY 0~LOWER CYLINDER PIN ASSEMBLY A~HYDRAULIC CYLINDER ~INCOMING-RIGHT P~CLAW PIVOT PIN ASSEMBLY H~EXTEND-RIGHT M~CYLINDER FITTING ~RETRACT-LEFT B~PRESSURE RELIEF MANIFOLD ~EXTEND-LEFT ~INCOMING LEFT 2 ~ CARTRIDGES 1 ~ BODY ~CLAW ASSEMBLY ITEM DESCRIPTION PART NUMBER NUMBER R~CLAW POINT-MALE HYDRAULIC CYLINDER HY-CYL-04X14-207-496 BODY ~ HY-PREREL-BODY...
- Page 16 SIDES (SEE BELOW) GREASE TWO GREASE ZERKS LOCATED HERE, BE SURE CLAW IS IN THE RAISED POSITION Operations/Procedures/forks/ Engine Puller Claw Operator Manual/15-CLAW ENGINE PULLER GREASING INSTRUCTION SHEET.doc 4/15/08 www.sasforks.com 1-877-SAS-FORK © 2004, 1987 S.A.S. of Luxemburg, Ltd. Page 15...
Need help?
Do you have a question about the Crushing Forks and is the answer not in the manual?
Questions and answers