Related Manuals for AUTEC LK NEO 6
Summary of Contents for AUTEC LK NEO 6
- Page 1 LIULK6N03_eng-00 Instruction Manual for the use and the maintenance of the Radio Remote Control Original instructions Part C: LK NEO 6, LK NEO 8 and LK NEO 6 DF (Model LKN Type LA1CM, DA1DM) Transmitting Unit AIR SERIES...
- Page 3 THIS PART OF THE MANUAL CONSISTS OF: Part C - Information, instructions and warnings for the LK NEO 6, LK NEO 8 and LK NEO 6 DF (Model LKN Type LA1CM, DA1DM) Transmitting Unit. The Manual consists of Part A – General, Part B – Conformity and Frequencies, Part C –...
- Page 4 It is also the responsibility of the Manufacturer and of the design professionals of the Machine on which the Autec Radio Remote Control is to be installed and used to be certain that the structure, condition, organization and markings of the Machine as installed at the facility is appropriate for and will allow for the safe and reliable use and control of the Machine through the Autec Radio Remote Control interface.
- Page 5 Laws, Regulations and Standards, even local, and that such Users and other Persons do in fact at all times operate or work with the Autec Radio Remote Control safely and ONLY in compliance with Autec instructions and warnings and with all applicable Laws, Regulations and Standards, even local.
-
Page 6: Table Of Contents
Technical Data Sheet ..................15 Plates ........................16 Plates on the LK NEO 6, LK NEO 8 and LK NEO 6 DF (Model LKN Type LA1CM, DA1DM) Transmitting Unit in a Radio Remote Control ..16 Plates on the LK NEO 6, LK NEO 8 and LK NEO 6 DF (Model LKN Type LA1CM, DA1DM) Transmitting Unit in a "Take &... - Page 7 8.17 BACK-UP UNIT ................... 35 Instructions for the User ..................37 Usage restrictions ..................37 User behaviour .................... 37 Belt and pouch with belt ................39 Maintenance ......................44 Malfunction signalled by the Transmitting Unit ..........44 Decommissioning and disposal ................. 46 AUTEC LIULK6N03_eng-00...
-
Page 8: Information On The Use Of Instructions
(Part A) of the Manual provided with the Radio Remote Control. Structure of the Instruction Manual The Manual for the use and maintenance of Autec Air series Radio Remote Controls consists of different parts, that altogether form the Manual; the Manual must be read carefully, understood and applied by the Radio Remote Control's Owner, User and by all those Persons that, for any reasons, may operate with the Radio Remote Control or with the Machine where it is installed. - Page 9 Receiving Unit. Usage and maintenance instruction as a whole are to be considered as an integral part both of the Autec Radio Remote Control and of the Machine, system, device or Machinery system where the Radio Remote Control is installed.
-
Page 10: Caption And Terminology
Information on the use of instructions Caption and terminology Contact Autec if any of the instructions, symbols, warnings or images are not clear and understandable, or if you have doubts or questions. In this part of the Manual, the terms listed below have the same meaning explained in the... -
Page 11: To Whom The Instructions Are Addressed
Regulation for the storage of instructions are described in the paragraph with the same title in the general part: please refer to that part. Intellectual property Restrictions connected to intellectual property are described in the paragraph with the same title in the general part: please refer to that part. AUTEC - AIR SERIES LIULK6N03_eng-00... -
Page 12: Brief Product Presentation
Series, Radio Remote Control and Unit The object of this part of the Manual is the LK NEO 6, LK NEO 8 and LK NEO 6 DF (Model LKN Type LA1CM, DA1DM) Transmitting Unit of an Autec Air series' Radio Remote Control. -
Page 13: Description Of The Transmitting Unit
Description of the Transmitting Unit Description of the Transmitting Unit Description of LK NEO 6 and LK NEO 8 Transmitting Units (Model LKN Type LA1CM) LEDs Technical data plate Actuator (selector, pushbutton) (if START pushbutton present) FUNCTION pushbutton Battery Command pushbuttons... -
Page 14: Description Of Lk Neo 6 Df Transmitting Unit (Model Lkn Type Da1Dm)
Description of the Transmitting Unit Description of LK NEO 6 DF Transmitting Unit (Model LKN Type DA1DM) Display Radio Remote Control identification plate Actuator (selector, pushbutton) (if present) Technical data plate Battery START pushbutton Power keyswitch (if present) FUNCTION pushbutton... -
Page 15: Technical Data
Technical data Technical data Technical data of LK NEO 6 and LK NEO 8 transmitting units (Model LKN Type LA1CM) Power supply (battery MHM03) ................3.6V Power supply (battery LPM01) ................3.7V Antenna ........................internal Housing material ..................PA 6 (20%fg) Protection degree .................. -
Page 16: Plates
Plates The following instructions refer to the plates on different types of Radio Remote Controls where the LK NEO 6, LK NEO 8 and LK NEO 6 DF (Model LKN Type LA1CM, DA1DM) Transmitting Unit may be used. Plates on the LK NEO 6, LK NEO 8 and LK NEO 6 DF (Model LKN Type... -
Page 17: Plates On The Lk Neo 6, Lk Neo 8 And Lk Neo 6 Df (Model Lkn Type La1Cm, Da1Dm) Transmitting Unit In A "Multi Units" Or "Multi Receiver" Radio Remote Control
Plates Plates on the LK NEO 6, LK NEO 8 and LK NEO 6 DF (Model LKN Type LA1CM, DA1DM) Transmitting Unit in a "Multi Units" or "Multi Receiver" Radio Remote Control Plate Position Content Key ID 0-1 (if present) -
Page 18: Light Signals
Red LED Green LED LEDs for "Data Feedback" function The LK NEO 6 and LK NEO 8 Transmitting Units always have a green LED [B] and a red LED [A] that provide information regarding the Radio Remote Control. Symbol Meaning This symbol identifies the red LED [A]. - Page 19 The red LED [A] blinks slowly (one The battery has less than 1h run time. blink per second). The red LED [A] blinks fast. The battery has a 10min run time. AUTEC - AIR SERIES LIULK6N03_eng-00...
- Page 20 30 s left before the Transmitting Unit automatically blink alternating. switches off. The green LED [B] repeats the sequence: 3 blinks and a pause, The UNPAIR procedure has been carried out. and the red LED [A] is steady on during start up. LIULK6N03_eng-00 AUTEC - AIR SERIES...
-
Page 21: Light Signals On The Lk Neo 6 Df Transmitting Unit (Model Lkn Type Da1Dm)
Battery Radio link The following icons are always available on the display of LK NEO 6 DF Transmitting Units: - red LED [A] and green LED [B] providing information about the Radio Remote Control, - battery [D] providing indication of the battery power level, - radio link [E] providing indication of radio link strength. - Page 22 Transmitting Unit, or this is a "BACK-UP steady on during start up. UNIT". The green [B] and red [A] LEDs The "Key ID 0-1" or the "ID internal tx memory" is blink 3 times per second during damaged. start up. LIULK6N03_eng-00 AUTEC - AIR SERIES...
- Page 23 The Radio link icon [E] consists of five vertical bars. The amount of dark bars is proportional to the quality of radio link. Symbol Meaning Strong radio link signal. Medium radio link signal. No radio link. AUTEC - AIR SERIES LIULK6N03_eng-00...
-
Page 24: General Operating Instructions
2. rotate the power keyswitch clockwise. 8.1.4 power keyswitch removal Perform the following operations to remove the power keyswitch: 3. rotate the power keyswitch anticlockwise, 4. pull the power keyswitch to remove it from the corresponding housing. LIULK6N03_eng-00 AUTEC - AIR SERIES... -
Page 25: Start Pushbutton
It is not possible to scroll the lines if icons only are displayed. The display lighting stays on for a time set by the Machine Manufacturer. No function other than the above mentioned functions must be given to the display pushbutton when the Unit is installed. AUTEC - AIR SERIES LIULK6N03_eng-00... -
Page 26: Enabling Switch
AND COULD CAUSE SERIOUS INJURY OR DEATH, AND/OR PROPERTY DAMAGE. The "Enabling switch" can only be associated to the enabling function to activate other commands, and cannot be connected to any other start up or movement function of the Machine. LIULK6N03_eng-00 AUTEC - AIR SERIES... -
Page 27: Battery
Indication of the battery charge level in the LK NEO 6 DF Transmitting Unit (Model LKN Type DA1DM) See paragraph 7.2.2 to check the battery charge level in the LK NEO 6 DF Transmitting Unit. AUTEC - AIR SERIES LIULK6N03_eng-00... -
Page 28: Id Internal Tx Memory
Indication of the battery charge level in the LK NEO 6 and LK NEO 8 Transmitting Unit (Model LKN Type LA1CM) Perform the following procedure to check the charge level of the battery in the LK NEO 6 and LK NEO 8 Transmitting Units: 1. -
Page 29: Zero-G Sensor
8.10 Vibration alarm The LK NEO 6 DF Transmitting Unit (Model LKN Type DA1DM) can be equipped with the "Vibration alarm". The "Vibration alarm" activates the Transmitting Unit's vibration if specific signals coming from the Machine are shown on the display. -
Page 30: Starting Up The Radio Remote Control
3. press the START pushbutton and hold it down until the green LED blinks quickly. 4. release the START pushbutton. When the green LED blinks slowly, the Radio Remote Control is active and it can send commands and activate the Machine. LIULK6N03_eng-00 AUTEC - AIR SERIES... - Page 31 - PIN 1=START pushbutton. - PIN 2=FUNCTION pushbutton. - PIN 3=START pushbutton. Autec will set a customized PIN code only upon request by the Machine Manufacturer or the Installer. 8.11.3 Power keyswitch + PIN code start up When the Receiving Unit is correctly powered on, perform the following procedure; press each pushbutton within 3 seconds after releasing the previous one: 1.
-
Page 32: Command Activation
The Transmitting Unit automatically switches off when: - the battery is flat (see paragraph 8.14.1), - the Radio Remote Control is not used for a certain time (see paragraph 8.14.2). To start the Radio Remote Control, see paragraph 8.11. LIULK6N03_eng-00 AUTEC - AIR SERIES... -
Page 33: Switching Off The Transmitting Unit
(SWITCH-OFF) to zero. Setting or removal of the automatic switch off time (SWITCH-OFF) is done by Autec and decided by the Machine Manufacturer or by the Installer, depending on the operation and functions they need on the Machine. -
Page 34: Data Feedback" Function
If the Transmitting Unit has an LED array for the "Data Feedback" function, specific Machine conditions are signalled if they are illuminated (by way of example: load limits, limit switch). The signalled conditions depend on the settings chosen by the Machine Manufacturer. LIULK6N03_eng-00 AUTEC - AIR SERIES... -
Page 35: Back-Up Unit
"BACK-UP UNIT", so that all Units belonging to the Radio Remote Control will show the same serial number. Autec cannot be held responsible if the serial number of the Transmitting Unit to be replaced has not been marked on the "BACK-UP UNIT". - Page 36 If the PIN code is correct, the green LED turns steady on and the Transmitting Unit switches off: this indicates that the address has been stored in the "BACK-UP UNIT". It is now possible to start the Radio Remote Control and control the Machine with the "BACK-UP UNIT" Transmitting Unit. LIULK6N03_eng-00 AUTEC - AIR SERIES...
-
Page 37: Instructions For The User
User by the Manufacturer of the Machine where an Autec Radio Remote Control (to which the LK NEO 6, LK NEO 8 and LK NEO 6 DF (Model LKN Type LA1CM, DA1DM) Transmitting Unit belongs) is installed. - Page 38 - keep at a safe distance from any risk situations originating from the use of the Machine where the Autec Radio Remote Control is installed; - avoid doing anything else while using the Radio Remote Control, such as, by way of example, operate other Machines and/or other devices, eat and/or drink, use communication devices (phone, radio phone, etc.), keyboards, computers, IT devices or AV equipment,...
-
Page 39: Belt And Pouch With Belt
Belt and pouch with belt The LK NEO 6, LK NEO 8 and LK NEO 6 DF (Model LKN Type LA1CM, DA1DM) Transmitting Unit always comes with a belt or a pouch with belt: the User must mount and use the belt and the pouch with belt as explained in the paragraphs 9.3.1 and 9.3.2. - Page 40 Instructions for the User LIULK6N03_eng-00 AUTEC - AIR SERIES...
- Page 41 Transmitting Unit, to the User, to people and/or property. Replace the belt or harness if it is damaged or worn. AUTEC - AIR SERIES LIULK6N03_eng-00...
- Page 42 Instructions for the User 9.3.2 Pouch with belt Assembly LIULK6N03_eng-00 AUTEC - AIR SERIES...
- Page 43 Transmitting Unit, to the User, to people and/or property. Replace the pouch with belt if it is damaged or worn. AUTEC - AIR SERIES LIULK6N03_eng-00...
-
Page 44: Maintenance
Receiving Unit " in "Part D" of the not work correctly. (one blink per second). Manual. The red LED is steady The STOP pushbutton is Unlock the STOP pushbutton. on during start up pressed or damaged. LIULK6N03_eng-00 AUTEC - AIR SERIES... - Page 45 The UNPAIR procedure the sequence: 3 blinks provided in the document and a pause, and the "Menu of Transmitting Perform the ALIGNMENT procedure. red LED is steady on Unit (MTU)" has been during start up. carried out. AUTEC - AIR SERIES LIULK6N03_eng-00...
-
Page 46: Decommissioning And Disposal
Decommissioning and disposal Instructions for correct decommissioning and disposal of Radio Remote Controls are described in chapter "Decommissioning and disposal" in "Part A" of the Instruction Manual. Therefore, please refer to that part of the Manual. LIULK6N03_eng-00 AUTEC - AIR SERIES... - Page 48 Via Pomaroli, 65 - 36030 Caldogno (VI), ITALY PH: +39 0444 901000 - Fax: +39 0444 901011 info@autecsafety.com - www.autecsafety.com MADE IN ITALY...