ADC Spectrum 7.0 Installation Manuals

Hide thumbs Also See for Spectrum 7.0:

Advertisement

Quick Links

ADC Spectrum 7.0
Installation Guide
ADCP-77-xxx  Issue 1  12/2009
D-xxxxxx-x-xx Rev A

Advertisement

Table of Contents
loading

Summary of Contents for ADC Spectrum 7.0

  • Page 1 ADC Spectrum 7.0 Installation Guide ADCP-77-xxx  Issue 1  12/2009 D-xxxxxx-x-xx Rev A...
  • Page 2 CD. In no event shall ADC be liable for any damages resulting from loss of data, loss of use, or loss of profits, and ADC further disclaims any and all liability for indirect, incidental, special, consequential or other similar damages.
  • Page 3: Table Of Contents

    Host Unit ......................5 DART Remote Unit ....................6 IF Expansion Unit....................7 Main Remote Access Unit ..................8 Secondary Remote Access Unit ................9 Omni Antenna ....................10 Installation ......................11 Cascading......................14 Specifications ......................15 Contacting ADC ...................... 17...
  • Page 4: Preface

    Preface REFACE This manual provides basic installation instructions for a ADC ® Spectrum 7.0 system. Revision History Initial release. Document Cautions and Notes Two types of messages, identified below, appear in the text: CAUTION! Caution text indicates operations or steps that could cause personal injury, induce a safety problem in a managed device, destroy or corrupt information, or interrupt or stop services.
  • Page 5: Standards Certification

    300 kHz and 100 GHz. Limits have been set for portable, mobile, and fixed equipment. ADC products fall in the category of fixed equipment; products intended to be permanently secured and exposures are evaluated for distances greater than 20cm (7-7/8”).
  • Page 6: Introduction

    • with each IFEU in the Expansion Unit supporting up to eight Main RAUs (one per IFEU FWD/REV F connector paired ports). Page 4 FlexWave Prism Remote Unit Installation Guide ADCP-77-072 • Issue 2 • 11/2009 © 2009 ADC Telecommunications, Inc...
  • Page 7: Host Unit

    • One DCV Power board • Eight RF DART modules for Wireless Operator RF input from BTS or BDA • Replaceable Fans for cooling FlexWave Prism Remote Unit Installation Guide Page 5 ADCP-77-072 • Issue 2 • 11/2009 © 2009 ADC Telecommunications, Inc.
  • Page 8: Dart Remote Unit

    • Eight RF DART boards with eight QMA connector IF inputs and eight QMA connector IF outputs to the IF Expansion Unit (IFEU) • Replaceable Fans for cooling Page 6 FlexWave Prism Remote Unit Installation Guide ADCP-77-072 • Issue 2 • 11/2009 © 2009 ADC Telecommunications, Inc...
  • Page 9: If Expansion Unit

    – eight QMA connectors that go to the DRU • One Micro controller board • One DC/DC board • Backplane • Replaceable Fans for cooling FlexWave Prism Remote Unit Installation Guide Page 7 ADCP-77-072 • Issue 2 • 11/2009 © 2009 ADC Telecommunications, Inc.
  • Page 10: Main Remote Access Unit

    800/900 SMR 700 SISO/AWS 800/AWS To IF Expansion Unit Connects up to To IF Expansion Unit (IFEU) three Secondary RAUs (IFEU) (SRAUs) Page 8 FlexWave Prism Remote Unit Installation Guide ADCP-77-072 • Issue 2 • 11/2009 © 2009 ADC Telecommunications, Inc...
  • Page 11: Secondary Remote Access Unit

    Band 1 and 2 Boards RAU pairing examples: 850/1900 700/700 MIMO 800/900 SMR 700 SISO/AWS 800/AWS Connects to Main RAU (MRAU) FlexWave Prism Remote Unit Installation Guide Page 9 ADCP-77-072 • Issue 2 • 11/2009 © 2009 ADC Telecommunications, Inc.
  • Page 12: Omni Antenna

    • 72-inch pigtails that are plenum-rated cables with N (male) connectors NOTE: Two antennas per RAU is required for MIMO performance. Page 10 FlexWave Prism Remote Unit Installation Guide ADCP-77-072 • Issue 2 • 11/2009 © 2009 ADC Telecommunications, Inc...
  • Page 13: Installation

    2 Connect the provided Vdc power cables to the +V and –V power-supply terminals. CAUTION! The Power Supply requires 2-20amp 120VAC outlets. FlexWave Prism Remote Unit Installation Guide Page 11 ADCP-77-072 • Issue 2 • 11/2009 © 2009 ADC Telecommunications, Inc.
  • Page 14 Module IF OUT connector. 4 Connect F connector CATV cable from IFEU FWD Module Port IF OUT to MRAU FWD IF IN F connector. Page 12 FlexWave Prism Remote Unit Installation Guide ADCP-77-072 • Issue 2 • 11/2009 © 2009 ADC Telecommunications, Inc...
  • Page 15 SRAU Secondary FWD F connector. b Connect F connector CATV jumper cable from MRAU REV Secondary F connector to SRAU Secondary REV F connector. FlexWave Prism Remote Unit Installation Guide Page 13 ADCP-77-072 • Issue 2 • 11/2009 © 2009 ADC Telecommunications, Inc.
  • Page 16: Cascading

    You add bands by inserting DART cards and CATV jumper between the Main and new Secondary RAUs, as shown below. 1 to 16 cascaded Expansion Units support up to 128 RAU locations. Page 14 FlexWave Prism Remote Unit Installation Guide ADCP-77-072 • Issue 2 • 11/2009 © 2009 ADC Telecommunications, Inc...
  • Page 17: Specifications

    Host Unit and Dart Remote Unit Mounting 19- and 23-inch rack Dimensions (Rack mountable) 5.25" x 19.00" x 19.00" Weight <25 Pounds FlexWave Prism Remote Unit Installation Guide Page 15 ADCP-77-072 • Issue 2 • 11/2009 © 2009 ADC Telecommunications, Inc.
  • Page 18 Weight 7.49 Pounds Remote Access Unit Power Requirements Power Source 54 VDC (from IFEU) Element Management Embedded EMS SNMP Based Management Page 16 FlexWave Prism Remote Unit Installation Guide ADCP-77-072 • Issue 2 • 11/2009 © 2009 ADC Telecommunications, Inc...
  • Page 19: Contacting Adc

    77-079 ADCP Number: Contents herein are current as of the date of publication. ADC reserves the right to change the contents without prior notice. In no event shall ADC be liable for any damages resulting from loss of data, loss of use, or loss of profits and ADC further disclaims any and all liability for indirect, incidental, special, consequential or other similar damages.
  • Page 20 Website: www.adc.com...

Table of Contents