Samsung WF45H6 Series Installation Manual

INSTALLATION GUIDE

WASHING
MACHINE
Parts supplied
Water supply hoses
Type1 Type2
Wrench
Tie strap Hose guide
(Except for WF36J4*,WF45K*, WF50K*
(Except for Bolt hole covers
(option)
WF45H6*,WF45K* model) model)
1
PREPARATION.
□ CHECK : The floor must be sturdy. (Carpet and soft tile surfaces are not permitted.
1. Check the installation location.
2. And move the washer to the installation location.
* When installing the washer on a pedestal, install the pedestal according to its manual.
2
UNPACKING WASHER.
Models with handles *Models without handles
 CAUTION: The shipping bolts must stay tightened during this unpacking.
3
REMOVING ALL SHIPPING BOLTS (3 OR 4 BOLTS) DEPENDING ON THE MODEL.
Remove all shipping bolts at the
lf applicable
back of washer with supplied
spanner. (Except for WF45H6*,
WF45K* model)
 CAUTION: Failure to remove the shipping bolts will cause vibration and noise.
4
COLD & HOT WATER HOSES INSTALLATION ON FAUCETS.
Coupling Rubber
washer
Make sure a Rubber washer is
Tighten Coupling by hand until
inside each coupling on both ends. it is snug.

5 Water Supply is separately. (Only for WF36J4*, WF45K*, WF50K* model) To order, please refer to call center number on the back page of your " User Manual " .
WATER HOSES INSTALLATION ON WASHER.
COLD (Left) HOT (Right)
Water Water
Connect one end of the COLD/ Tighten Coupling by hand until
HOT water supply hoses to the it is snug.
each COLD/HOT water supply
intakes at the back of the washer.
 CAUTION: Make sure that the HOT & COLD hoses are not switched with each other.
Parts needed(Sold separately)
Tools needed
Anti-slip pads
Tape measure
* To order, please refer to call center number
on the back page of your "User Manual"
When unpacking the washing machine,a
collaboration of two persons is required. Do not lay
the machine on its front face when removing the
bottom cushion.
* Models that do not feature handles:
Remove the top cushion from the washing machine
and put the top cushion (or its equivalent) on the
floor. Lay the washing machine on the top cushion
and then remove the bottom cushion.
Make sure to lay the washing machine to its side.
Hold the shipping bolt with your Fill the holes with the supplied
hand and pull it through the bolt hole covers.
wide section of the hole. Repeat
for each shipping bolt.
Rubber washer
Then tighten two-thirds of a turn Run water in a bowl or basin to get
rid of any debris inside hose. Check
with pliers.
for HOT and Cold water supply.
Then tighten two-thirds of a turn For proper operation, make sure
with pliers. both Hot & Cold hoses from faucets
are connected to the corresponding
Hot / Cold water inlets on the washer.
6
CONNECTING THE DRAIN HOSE.
Drain hose
Carpenter's
Pliers
Flat screwdrilver
level
Hose guide
To keep the drain hose spout
bent, use the supplied plastic
hose guide.
7
MOVE THE WASHER TO ITS FINAL LOCATION AND MAKE SURE IT IS LEVELED.
Confirm whether washer is well seated and does not shake. Adjust
leveling legs, if necessary.
8
LEVEL THE WASHER BY ADJUSTING THE FOUR LEVELING LEGS.
Level the washer by turning the leveling wheel
clockwise or counter clockwise to the required level
with the supplied wrench. (Except for WF45H6*,
WF45K* model)
 CAUTION: Your washer must be leveled on all four sides. An unlevel washer may cause vibration.
9
Installing the anti-slip pad
1. Completely clean the bottoms of the adjustable legs and wipe away any dust and oil.
2. Mark the locations of the adjustable front legs of the washing machine where the anti-slip
pads should be installed.
HOT COLD
3. Attach the anti-slip pad by tilting or moving the washing machine. When you attach the pad,
remove the plastic film from the pad and attach the sticker side of the pad to the floor so
that the rough side is facing upward. You should not attach the sticker side of the pad to an
adjustable leg.
4. After installing the washing machine and anti-slip pad, check if the adjustable legs are level
again.
Anti-Slip pad is sold separately. (Except for WF36**,592** model) To order,please refer to
call center number on the back page of your "User Manual"
10
Final Test : Water leakage , Vibration & Noise
1. Powering your washing machine.
2. Run a test cycle(Rinse+Spin) with small amount of laundry such as 4~5 Towels.
(1) Check for any leakage at the hose connections.
 If water leaks while water is being supplied or drained, check the water connections. (Refer to Step 4,5,6)
(2) Check for vibration and noise.
 If the washer rocks and vibrates excessively, level your washer again. (Refer to Step 7,8)
Visits by a Service Engineer to explain functions, maintenance or installation is not covered by warranty.
INSTALLATION
COMPLETION CHECKLIST
□
Washer plugged in, power OK
Case 1. Wash basin Case 2. Laundry tub
96" Max
18" Min
Tie strap
The drain hose must be placed Laundry tub must be no shorter
at a height between 23.6 in than 18 in (46 cm) and no longer
(60cm) and 35.4 in (90cm). than 96 in (245 cm).
Your washer must be leveled on all four sides. Use a carpenter's level
on all four corners of your washer to ensure it's level.
Check whether washer shakes and level
again, if necessary.
□
No water leakage
□
Water hose connected properly
□
Drain hose connected properly
French on back 
Spanish on back 
Case 3. Stand pipe
Hose
Hose
retainer
retainer
8" Max
6" Min
96" Max
18" Min
Tie strap
Do not insert the drain hose
too far into the stand pipe: 6 - 8
inches, and no more.
When your washer is leveled, tighten
the locking nuts using the wrench or (-)
flathead screwdriver.
Rough side
Sticker
□
No vibration / noise
□
Washer leveled
□
Shipping bolts removed
DC68-02580C-11