Compact freely programmable automation device, a din-rail-attachable, monitoring-, controlling- and regulating device, can be as a master device and slave device in the modbus bus, the din-standard-compatible structure of the device enables installation t
Page 1
- Ouflex M BA is a DIN-rail-attachable, monitoring-, controlling- and regulating device. - Ouflex M BA can be as a master device and slave device in the Modbus bus. - The DIN-standard-compatible structure of the Ouflex M BA device enables installation to most common cabinets.
Page 2
"Alarms -> Active alarms". Uncleared alarms are marked with an exclamation mark at the start of the line. Hidden menus Some of the information in your Ouflex M BA device may be hidden. You can see the hidden menus by pressing OK for a few of seconds. Similar- Press OK ly, you can hide them again by pressing OK for a few of seconds.
3.2 Bus points ............................13 3.3 Time programs ............................13 4 Settings ..........................15 5 Measuring point control/manual control ..............16 6 Naming ..........................16 7 Remote use ........................17 Optional accessories ......................18 Ouflex M BA structure ......................19 Technical information ......................20...
Enter hours 19:44 The Ouflex M BA clock takes daylight savings and leap years into ac- count automatically. The clock has a backup for power outages up to hh:mm three days.
(the message center number is not visible on the display). Retest the text message communication. SMS PIN: If the SIM card has PIN inquiry in use, Ouflex M BA device asks you to enter the PIN. SMS PIN Entering the code: Approve: Press and hold OK Use arrow buttons and press OK to accept each number.
Print2) C NO C NO C NO C NO C NO C NO ween Ouflex M BA and M-Link is 10m and all 4 pairs must be con- 9 10 11 12 13 14 15 16 17 18 19 20 System settings nected.
Page 7
Ouflex M BA device can be a master device in two Modbus RTU. It Parity None> is shown in the first line in which the bus Ouflex M BA is the master Delay between packages > device. All the devices in the same bus should be set to the same set- ting value of the baud rate, data bits, stopbits and parity.
On > If all the settings are correct, the status of the device is “Connected”. If Ouflex M BA is connected in the network, but you want to prevent browser connection, for example for data security reasons, select ”Off” of WEB user interface.
You can read Ouflex M BA device information and change settings. In use You can read Ouflex M BA device information but you can not change set- tings without entering the lock code. The factory setting of lock code is 0000.
C NO 9 10 11 12 13 14 15 16 17 18 19 20 Select: ”Yes” Ouflex M BA reboot to start the update of the new software. The up- Document code and revision Document type Date 09.06.2015 Drawing XL740-A-01 Author dating of the software takes few minutes.
Routting schedule See following page. Alarm receivers A GSM modem can be connected to the Ouflex M BA for sending aa alarm as Alarm receivers text message to the alarm team. The alarms are sent to correct team accor- Team 1 >...
Page 12
4. To exit edit mode, press ESC. If the alarms are routed, alarms are forwarded as text message to alarm team according to the routing schedule. You can acknowled- ge an alarm by forwarding the same message to the Ouflex M BA.
Wireless > 3.3 Time programs Point info -> Time programs In Ouflex M BA, weekly programs can be added to different func- Time programs H1 Heating temp. drop Off > tions - such as temperature drops, car heating and control of lights.
Page 14
Weekly schedule Point info -> Time programs -> Weekly schedule Graphic view Weekly schedules include graphic views (in general view mode and Weekly schedule MO > edit mode) with data on the exact time that new control commands TU > are received.
You can lock the settings in Ouflex device system settings. If a GSM modem is connected to Ouflex M BA device and the setting values have been brought into SMS interface, you can edit settings by text message. Send a message “ Key words”. The reply message shows you which key words are in use in the application.
25 % > If a GSM modem is connected to Ouflex M BA device and the setting values have been brought into SMS interface, you can edit settings by text message. Send a message “ Key words”. The reply message shows you which key words are in use in the application.
Attention! If the controller has a device ID in use, always write the device ID in front of the key word Internet-based on-line control room If M-Link device (optional) is connected to the Ouflex M BA, you will get a Modbus TCP / IP interface to the Ouflex M BA.
Insert SIM card into the slot and make sure it settles properly. Push the slot back to its place. Set the SIM card PIN code as Ouflex M BA device PIN code. Make sure PIN inquiry is in use in the SIM card.
GSM phone. Additional Control panel The Ouman LCD external display is connected to the flap cover over the RJ12 jack. Use Ou- man cable LCD CABLE M. XM1362_Ouflex M BA_User manual_ENG_ 20180912...
Need help?
Do you have a question about the OUFLEX M BA and is the answer not in the manual?
Questions and answers