Related Manuals for Kenco Kenlift
Summary of Contents for Kenco Kenlift
- Page 1 Attachment Solutions ® The Kenlift Concrete median barrier handling device Operators Manual Conforms to ASME B 30.20, BTH-1 Design Category B, Service Class 3...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Section I. General Information...................... 1 Section II. Safety ..........................1 Section III. Identification of Major Components ................3 Section IV. Setup..........................3 Section V. Operation........................5 Section VI. Maintenance........................7 Section VII. Inspection Criteria ......................8 Section VIII. -
Page 3: General Information
Section I. General Information ® May we take this opportunity to thank you for purchasing the KENCO Kenlift ® highway median barrier wall handling system. The Kenlift System provides the ultimate in ® below the hook concrete highway barrier handling versatility. The Kenlift is quality engineered to provide years of trouble free, low maintenance performance. - Page 4 2. Do not wear loose clothing, jewelry, or hairstyles that could become entangled in the KENCO ® Kenlift or rigging hardware. 3. Keep hands, feet, and any other appendages clear of Kenlift® while in operation. C. Operation Safety 1. DO NOT ATTEMPT TO OPERATE OR PERFORM MAINTENANCE ON THE ®...
-
Page 5: Identification Of Major Components
1. Use as few rigging components (shackles, slings, chain, etc.) as possible. 2. ALL RIGGING COMPONENTS MUST HAVE A WORKING LOAD LIMIT THAT IS EQUAL TO OR GREATER THAN THE COMBINED WEIGHT OF INTENDED ® LOAD PLUS THE Kenlift ® KENCO Kenlift Operation Manual... - Page 6 ® ® TO Kenlift BE OF A RATED CAPACITY LESS THAN THAT OF THE Kenlift 4. DO NOT RIG UNPROTECTED NYLON SLINGS OR WIRE ROPE DIRECTLY THROUGH LIFT BAIL. 5. IF USING EQUIPMENT OTHER THAN A CRANE: USE RIGGING OF SUFFICIENT ®...
-
Page 7: Operation
6. Raise Kenlift and load in a smooth motion, do not “jerk”. 7. Deposit at desired location. ® 8. Release tension on lift cable. (Note: avoid undue slamming of the Kenlift into open position to prolong actuator life.) ® ®... - Page 8 3. Ensure that all persons are clear of Kenlift and wall. 4. Release tension on lift cable. 5. Lift latch handle. 6. Raise Kenlift slowly until latch bar is inboard of notches on latch handle. 7. Release handle and move away from lift. ® 8. Raise Kenlift and load in a smooth motion, do not “jerk”.
-
Page 9: Maintenance
Section VI. Maintenance A. Daily: ® 1. Visually inspect Kenlift for signs of stress and wear. 2. Check that bolts and nuts are snug. 3. Ensure free movement of all components. 4. Ensure that all warning labels are present and readable. -
Page 10: Inspection Criteria
Section VII. Inspection Criteria ® THE KENLIFT UNIT AND ALL OF ITS ASSOCIATED COMPONENTS SHALL BE REMOVED FROM SERVICE AND TAGGED APPROPRIATELY UNTIL RECERTIFICATION BY A QUALIFIED INDIVIDUAL IN ANY OF THE FOLLOWING CONDITIONS: A. General 1. Cracking in any component or member. -
Page 11: Parts/Drawings
Section VIII. Parts/Drawings 8 27 ® KENCO Kenlift Operation Manual... - Page 12 ® KENCO Kenlift Operation Manual...
- Page 13 DO NOT alter or modify this equipment. DO NOT use lifter for other than designated purposes. DO NOT lift unbalanced loads. DO NOT allow load to contact other objects while suspended. INSPECT LIFTER PRIOR TO EACH USE. ® KENCO Kenlift Operation Manual...
- Page 14 1.25 X 4 BOLT .5 X 1.5 BOLT 1.25 NUT 1.25 FLAT WASHER .5 NUT .5 STAR INTERNAL .5 LOCK WASHER SMALL BADGE DANGER STICKER IDTAG BTH TAG LG. WARNING STICKER SM. WARNING STICKER ID STICKER ® KENCO Kenlift Operation Manual...
-
Page 15: Available Options
® 2. The Kenlift with alignment leg attachment is simply guided by the hoist operator into ® the wall. The alignment legs then contact the wall surface and align the Kenlift properly with the wall. B. Leveling link. 1. Allows for level handling of single faced asymmetrical median wall sections. -
Page 16: Warranty
1. KENCO Corporation (KENCO) warrants the KENCO Kenlift lifting device (not including pads or consumable items) sold by KENCO to be free from proven defects in material and workmanship for a period of six (6) months from the delivery date to the original customer.