Download Print this page
iPazzPort KP-810-21BTL Instructions Manual

iPazzPort KP-810-21BTL Instructions Manual

Mini bluetooth keyboard
Hide thumbs Also See for KP-810-21BTL:


Mini Bluetooth Keyboard
迷你蓝 牙键盘



Summary of Contents for iPazzPort KP-810-21BTL

  • Page 1 Mini Bluetooth Keyboard 迷你蓝 牙键盘 (KP-810-21BTL) instructions 使用指南...
  • Page 2: Power Switch

    open searching open players FN+Lock Selection Adjustable mouse speed two speed can be adjustable open my computer open mail box open the browser mute home gape mouse right mouse left FN+Touch the board the scrollbar look through the web Power Switch...
  • Page 3 Safety Precautions Accessories Safety Matters Only use factory specified parts.Please use the supplied travel charging cable.the use of other To avoid injury,death of personnel or damage to the charging devices may be dangerous. equipment the operator must refer to the explanations in this User’s Manual Battery:There is a lithium-ion rechargeable battery Overview...
  • Page 4 Introduction Interference Product overview After finishing using the keyboard,push the switch Touchpad to the off position.This turns off the power,of the This product was added to the innovative function keyboard.The USB receiver should be plugged out Of the mouse wheel,when you press the Fn button from the PC and then inserted back in the keyboard With your fingers Touch anywhere in the sliding so it is being kept safely.
  • Page 5 Notes : This product has the configuration of A and Computer system requirements B configuration can choose Windows Configure A: lithium battery version,this version built Mac OS in rechargeable lithium battery,additional charge Android/iOS OS USB line. Configure B: Install AAA* 2 battery,this version dose Maintenance not support the charging function.
  • Page 6 Troubleshooting Below are some basic troubleshooting scenarios for Bluetooth icon the device.Please contact support from the place of 2.Turn on unit by moving the power switch to ON, purchase if you are unable to resolve any issuse with press key BLUETOOTH RESET indicated till LED3 the device.Problem Possible issue Solution blink then release it(about 2-5 seconds) ,that means your unit is ready and searching other Bluetooth...
  • Page 7 9.LED3 will goes out when connection is established 3.Click “Start”,“Control Panel”(make sure you're in Classic successfully. View),and then double-click Bluetooth Devices.Select NOTE: keyboard functions WILL NOT work until a “Add”. bluetooth connection with the computing device is 4.In the Add Bluetooth Device Wizard,select the “My completed.
  • Page 8 Bluetooth keybaord Bluetooth Reset An window like below will popup indicating that system is search a devie to add... Then you will be required to input a pass code for your device, please do type the code with bluetooth keyboard, then press Enter Bluetooth Keyboard NOTE:1.
  • Page 9: Connect To Ipad/ Iphone

    CONNECT TO iPAD/ iPhone 1.Turn your Bluetooth Keyboard on by switch button to on, press Bluetooth Reset key till LED3 flash. 2.Turn on your iPhone,tap“settings”=>“Bluetooth”, then your iPhone will search the other Bluetooth for pairing, “Bluetooth keyboard” will be listed when Bluetooth keyboard would like to pair with your iPad system find your Bluetooth keyboad.
  • Page 10 4.Icon of Bluetooth Keyboard will appear in the list when bluetooth keyboard is found,tap this icon for pairing 5.Tap “Bluetooth Keyboard”,then system will install driver and prompt you to input pass code you must type the pass code with your bluetooth keyboard. - Please be noted that your mobile can’t be connected and can’t be used if your mobile have no HID profile or contact our service dept.
  • Page 11 1.Configure A:charge the device for at unit does least 15minutes.Configure B:Replacement of 1.Low battery power. not respond the AAA.2 battery 2.Unit is not turned on. 2.Check if the switch selected to the“ON”position. Keyboard can not 1.The receiver may not be establish a 1.Disconnect and reconnect inserted correctly...
  • Page 12 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
  • Page 13 installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna.