Lorell LLR60338 Operating Instructions

INSTRUCCIONES DE
Silla Ejecutiva de Cuero
de Respaldo Alto con
Acabado de Cereza
LLR60338
LLR60339
SI LE FALTA PARTES O TIENE OTRO ASUNTO QUE LE
1
2 CONCIERNE PORFAVOR LLAMENOS A NUESTRO NUMERO
GRATUITO:
1-800-295-5839 o e-mail: Parts@sprich.com
LUNES – VIERNES 9:00 A.M. A 4:00 P.M. – TIEMPO OFICIAL DEL
ESTE
Por favor provee la siguiente información:
1.Nombre Completo
2.Domicilio – Porfavor no incluye P.O. Box ya que nuestros
portadores no pueden entregar a un domicilio de P.O. Box
3.Numero de Telephono
4.Numero de Modelo
5.Numero de Parte
6.Cantidad
7 Razón por el Pedido
Note: Nuestra póliza es de mandar todos los pedidos de partes con
1
2
transportacion terrenal, si sus requesitos son de mandar partes via
correo de noche o de siquiente dia,, porfavor provee su designado
portador y cuenta de numero.
ADVERTENCIA
1. Sólo una persona a la vez debe usar este producto.
CARACTERÍSTICAS
2. No use esta silla a menos que todos los pernos, tornil-
los y perillas estén firmemente apretados.
• AJUSTE DE ALTURA
3. Compruebe cada tres meses o según se necesite que
Para levantar el asiento retire la presión del asiento y levante la
todos los pernos, tornillos y perillas estén apretados.
palanca (1). Para bajar la altura del asiento siéntese en la silla y
4. No voltee la perilla de tensión del respaldo cuando
levante la palanca (1).
reduzca la tensión.
• FIJACIÓN DEL AJUSTE DE TENSIÓN DE
5. Elimine apropiadamente el material de empacado.
INCLINACIÓN
No use la cubierta plástica como cobertura de cabeza.
Para comodidad individual, esta silla cuenta con un ajuste
Puede causar asfixia.
que permitirá al usuario cambiar la tensión de la función de
6. No use la silla como escalera manual.
inclinación. Gire la perilla (2) a la derecha para aumentar la
7. Use esta silla sólo para el propósito para el que se ha
tensión y a la izquierda para disminuir la tensión. Para fijarla,
diseñado.
regrese la silla a la posición vertical y empuje la palanca (1)
8. Use sólo un detergente suave para limpiarla.
hacia adentro. Para soltarla, tire de la palanca (1) hacia afuera.
NOTA: Tenga cuidado de no girar completamente la perilla de
ajuste de la inclinación de respaldo.
LLR60335_052405
OPERACION
7
8,11
DETAIL A:
Assemble the back support over the
seat plate
9
12
Before You Begin:
Open, identify and count all parts prior to assembly. Lay out the parts on
a non-abrasive surface such as a carpet or blanket. You will need the tools identified below:
1. Phillips Head Screw Driver
2. Allen Wrench (Provided)
3. Socket Wrench (Provided)
STEP 1
Insert five Casters (2) into Base (1). Insert Pneumatic Cylinder (3) into Base (1) and slip Bellows (4) over cylinder shaft.
STEP 2 Attach Seat Plate (5) to Seat Cushion (6) with the arrow towards the front of the chair using four Short Screws (9).
TIGHTEN ALL FOUR SCREWS COMPLETELY
STEP 3 Attach Back Support (12) to Seat Cushion (6) using four Short Screws (9). DO NOT FULLY TIGHTEN SCREWS. IMPORTANT NOTE:
MAKE SURE YOU HAVE ASSEMBLED THE BACK SUPPORT PLATE (12) OVER THE SEAT PLATE (5) THAT YOU ATTACHED
TO THE SEAT CUSHION IN STEP 2. (SEE DETAIL A)
STEP 4
Align the holes in the Arms (10L and 10R) with the holes in the Seat Cushion (6) and Back Cushion (7). Attach Arms (10L and 10R) to Seat
Cushion (6) and Back Cushion (7) using six Long Screws (8). FULLY TIGHTEN ALL SCREWS.
STEP 5
Cover the screws on the arms with six caps (11).
STEP 6
Place the assembled seat on top of Pneumatic Cylinder (3) and apply downward pressure.
ATTENTION: MAKE SURE ALL SCREWS ARE FULLY TIGHTENED BEFORE USING CHAIR.
LLR60335_052405
LLR60338/LLR60339
ASSEMBLY INSTRUCTIONS
10L
10R
8,11
12
9
6
5 9
HARDWARE IDENTIFICATION
PART
9 4
1. Base . . . . . . . . . . . . . . . . . . . . 1
2. Casters . . . . . . . . . . . . . . . . . . 5
9
3 3. Pneumatic Cylinder . . . . . . . . . 1
4. Bellows . . . . . . . . . . . . . . . . . . 1
5. Seat Plate . . . . . . . . . . . . . . . . 1
6. Seat Cushion . . . . . . . . . . . . . . 1
7. Back Cushion . . . . . . . . . . . . . 1
8. Long Screws . . . . . . . . . . . . . . 6
1 9. Short Screws . . . . . . . . . . . . . . 8
2
10. Arms Left (10L) Right (10R) . 2
11. Caps . . . . . . . . . . . . . . . . . . . 6
12. Back Support (pre-installed) . 1
13. Allen Wrench (not shown) . . . 1
14. Socket Wrench (not shown) . 1
1
2
QTY
1
2
FEATURE
• HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever
(1). To lower seat height sit on chair and lift lever (1).
• LOCKING TILT ADJUSTMENT
For individual comfort, this chair has been equipped
with an adjustment that will allow the user to change the
tension of the tilting feature. Turn knob (2) clockwise
to increase tension and counter-clockwise to decrease
or ease the tension. To lock return chair to the upright
position and push lever (1) in. To unlock pull lever (1) out.
NOTE: Be careful not to loosen back tilt adjustment knob
completely.
LLR60335_052405
OPERATING INSTRUCTIONS
Leather High-Back Executive
Chair with Mahogany Wood
Finish
LLR60338
LLR60339
IF YOU ARE MISSING PARTS OR HAVE OTHER CONCERNS PLEASE
CALL OUR TOLL FREE NUMBER:
1-888-295-5839 OR EMAIL: Parts@sprich.com
MONDAY-FRIDAY 9:00 AM TO 4:00 P.M. - EASTERN STANDARD TIME
Please provide the following information:
1. Full Name
2. Physical Address - Please do not include a P.O. Box as our carriers
cannot deliver to a P.O. Box Address.
3. Phone Number
4. Model Number
5. Part Number
6. Quantity
7. Reason for the request
Note: Our policy is to send all parts requests with normal ground
transportation, if your requirements are to have these parts sent via
overnight or next day, please provide your designated carrier and account
number.
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts, screws, and knobs
are securely tightened.
3. Check that all bolts, screws, and knobs are tight every
three months or as needed.
4. Do not overturn back tilt knob when decreasing tension.
5. Dispose of packing material properly. Do not use plastic
cover as head covering. It may cause suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.