Download Print this page
Sharp SPC1100 Instructions & Warranty

Sharp SPC1100 Instructions & Warranty

Atomic qa wall clock
Hide thumbs Also See for SPC1100:

Advertisement

Quick Links

REMOTE TRANSMITTER
Recommended operating range: -50℃ to 70℃, -122℉ to 158℉
Resolution:
0.1℃/℉(above 0℃/32℉), 1℃/℉(below 0℃/32℉)
Humidity measuring range:
20% RH to 95%RH
Operating range:
20% RH to 95%RH
Resolution:
1%RH
RF transmission frequency:
433.92MHz
Remote transmitter:
1 unit
RF transmission range:
maximum 30 meters
Temperature sensing cycle:
around 50 seconds
POWER
Main unit:
1.5V, use 1 x AA 1.5V alkaline battery (for clock movement)
3V, use 2 x AA 1.5V alkaline battery (for LCD display)
Remote transmitter:
3V, use 2 x AA 1.5V alkaline battery
DIMENSION
Main unit:
273(W) x 360(H) x 5.3(D)mm
10.7(W) x 14.2(H) x 2.1(D)inch
Remote transmitter:
40(W) x 130(H) x 24(D)mm
1.6(W) x 5.1(H) x 0.9(D)inch
NOTE
Changes or Modifications not expressly approved by the party responsible could void the user's authority to operate
this device.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Thank you for your purchase of this quality clock. The utmost care has gone into the design and manufacture of your
clock. Please read these instructions and store them in a safe place for future reference.
The receiver unit has a clear, easy-to-read display that shows indoor temperature and humidity, outdoor temperature,
time, month, date, day. The remote sensor transmits the outdoor temperature. To receive the outdoor temperature,
place the sensor anywhere within 30 meters; the 433.92MHz technology means no wire installation is required.
The Atomic Clock will always be accurate to within one second as it receives daily WWVB updates. Daylight Saving
Time also automatically updates so there is no need to re-set the clock manually!
IMPORTANT: If the Atomic Clock does not receive the WWVB signal immediately, wait overnight and it will be
set in the morning.
The clock has a built in receiver that automatically synchronizes itself with the WWVB radio signal broadcast by the
US Government's National Institute of Standards & Technology (NIST) in Fort Collins, Colorado.
signal daily broadcast ensures that the atomic clock will always display the most accurate date and time.
FEATURES:
1
1
. QA Clock:
- Before insert the battery, select the time zone and DST mode. Once battery is inserted, the second hand will run
and stop at zero position (12:00), and then the minute and hour hands will start running and stop at zero position.
Then, the clock begins to receive the Atomic time signal automatically and it will take 3 - 10 minutes. If successfully
receive the signal, the hands will find their correct time and work normally.
NOTE:
1. The unit will automatically search for the time signal at 2:16am, 4:16am, 2:16pm, 4:16pm.
2. Closed area such as airport, basement, tower block or factory is not recommended.
3. While the atomic signal is flashing, the control panel is inactive.
2. LCD DISPLAY:
- Displays indoor/outdoor temperature; and current weather condition.
3. BATTERY COMPARTMENT AND DOOR:
- Use 2 x AA size batteries
SPC1100
4. ℃/℉ BUTTON:
- In normal mode, press the button to switch temperature unit ℃/℉.
Atomic QA Wall Clock
Instructions & Warranty
WWVB
M.SE T
REC
Reset
Channel
C / F
2
3
4 5 6
Atomic QA Clock
The WWVB radio
WWVB
M. SE T
REC
7
8
9 10
11
12 13
14

Advertisement

loading

Summary of Contents for Sharp SPC1100

  • Page 1 3. While the atomic signal is flashing, the control panel is inactive. 2. LCD DISPLAY: - Displays indoor/outdoor temperature; and current weather condition. 3. BATTERY COMPARTMENT AND DOOR: - Use 2 x AA size batteries SPC1100 4. ℃/℉ BUTTON: - In normal mode, press the button to switch temperature unit ℃/℉.
  • Page 2 5. Channel BUTTON: SETTING UP THE TRANSMITTER: - In the normal mode, press the button to switch the between channel 1, 2 and 3 to receive the 433.92MHz signal; 1. Remove the battery door and insert 2 AA batteries into the battery compartment and follow the polarities marked. press and hold the button for 3 seconds will pairing with the outdoor remote sensor.