Specifications - Palmgren 81093 Operating Manual & Parts List

Palmgren Operating Manual & Parts List
DESCRIPTION
Palmgren 6" Belt and 9" Disc Sander is constructed of rugged die
cast aluminum and cast iron providing stability and vibration-free
operation. The 6 x 48" belt and 9" diameter disc are used to sand,
deburr, bevel and grind large workpieces of wood, plastic and metal.
The 6 x 48" belt housing can be pivoted from vertical to horizontal
for sanding large, straight workpieces. The belt assembly includes a
tilting, cast iron table, quick release belt tension and tracking
mechanism, OSHA compliant safety guard with dust collection
port and easy opening side door for belt changes.
The 9" diameter disc can be used to sand or bevel surfaces with
the use of 0 to 45º scaled aluminum table. The 9" diameter disc
assembly includes a tilting table with miter gauge slot and dust
collection chute.
The two dust collection chutes with adaptable exhaust ports allow
for quick removal of dust. The adjustable miter gauge can be used
on both the belt and disc tables for guiding the workpiece at a
desired angle while sanding.
UNPACKING
Refer to Figure 1 and 2.
Check for shipping damage. If damage has occurred, a claim must
be filed with carrier. Check for completeness. Immediately report
missing parts to dealer.
The sander comes assembled as one unit. Additional parts which
need to be fastened to sander, should be located and accounted
for before assembling.
A Abrasive and aluminum disc with set screw
B Disc guard
C Disc dust chute
D Disc table with attached trunnions
E Work stop
F Belt table assembly
G Miter gauge assembly
Parts bag includes: two handles, three
3
two #10-24 x ⁄ " washer head screws, three M10 flat washers, one
8
M10 x 25 socket head bolt, four
5 ⁄ " flat washers, four 5 ⁄ -18 hex nuts and one each M2.5, M4, M6
16 16
and M8 hex wrenches.
A
D
Figure 1 – Unpacking
The stand comes unassembled and packed along with the sander
in the same box. Locate and identify all parts before attempting
assembly (Refer to Figure 2).
A Top Frame (4)
B Brace (4)
C Leg (4)
D Rubber Foot (4)
E 5 ⁄ -18 x 5 ⁄ Carriage Bolt (32)
16 8
5
F ⁄ -18 Hex Nut (32)
16
G 5 ⁄ Flat Washer (32)
16
1 1
⁄ -20 x ⁄ " washer head screws,
4 2
5 ⁄ -18 x 2" hex head bolts, eight
16
B
C
E
G
C
D
Figure 2 - Unpacking Stand

SPECIFICATIONS

Belt size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 x 48"
Belt platen area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Belt drum dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 x 6
Belt table dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Belt table tilts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 to 60º
Belt dust chute diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2"
Belt speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2700 SFPM
Disc diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9"
Disc table dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Disc table tilts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 to 45º
Disc dust chute diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11/2"
Disc speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3450 RPM
Base dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .SP, Locking rocker
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 HP, 120/240 V, 9/4.5 Amps
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 lbs
PROPOSITION 65 WARNING:
sanding, sawing, grinding, drilling and other construction activities
contains chemicals known to the state of California to cause can-
cer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other
masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures vary, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
F work in a well ventilated area and work with approved safety
equipment. Always wear OSHA/NIOSH approved, properly fitting
face mask or respirator when using such tools.
WARNING:
For your own safety, read all of the instructions and
precautions before operating tool.
CAUTION:
Always follow proper operating procedures as defined in
this manual even if you are familiar with use of this or similar tools.
Remember that being careless for even a fraction of a second can
result in severe personal injury.
BE PREPARED FOR JOB
• Wear proper apparel. Do not wear loose clothing, gloves, neck-
ties, rings, bracelets or other jewelry which may get caught in
moving parts of machine.
• Wear protective hair covering to contain long hair.
• Wear safety shoes with non-slip soles.
• Wear safety glasses complying with United States ANSI Z87.1.
Everyday glasses have only impact resistant lenses. They are
NOT safety glasses.
2
A
B
E
F
G
SAFETY RULES
Some dust created by power
81093
1
⁄ x 17"
8
1
⁄ "
8
7 ⁄ x 9 13 ⁄ "
8 16
7 ⁄ x 11 13 ⁄ "
8 16
1 ⁄ x 14 1 ⁄ "
2 2