DeRoyal Static-Pro Knee 4405 Instructions For Use

Model #4405
Static-Pro ® Knee
Static Progressive Orthosis
Single Patient Use Only
Rx Only
IMPORTANT
Please read all instructions, warnings and precautions
before use.
INTENDED USE
The DeRoyal Static-Pro ® Knee Orthosis is designed for
the treatment of joint stiffness and established soft
tissue contractures, which may have resulted from
trauma, immobilization or neurological disorders. The
orthosis should only be used under the supervision of a
qualified health care professional. Protocols for use
vary depending on the diagnosis and should be
determined after consulting with the patient's physician.
The Static-Pro ® Knee assists in either flexion or
extension in one unit.
CONTRAINDICATIONS
The Static-Pro ® Knee Orthosis should not be used if
any of the following conditions exist: Severe spasticity,
severe osteoporosis and/or thrombophlebitis. If pain,
numbness, swelling or skin irritation occurs while
wearing the orthosis, it should be removed. The
patient should be re-evaluated and appropriate
adjustments made.
PRECAUTION
Caution should be used if any of these conditions exist:
peripheral vascular disease, healing skin wounds, mild
spasticity, heterotrophic ossification and mild osteoporosis.
Be careful not to apply excessive tension to patients
with decreased sensation or feeling in the knee or leg.
INSTRUCTIONS FOR USE
CAUTION: The DeRoyal Static-Pro ® Knee Orthosis is a
non-ambulation orthosis. The intended use is for the
patient to be in a sitting or supine position. Ambulating
while wearing the orthosis may cause it to migrate
down the leg, making the unit ineffective.
IMPORTANT: Before applying the orthosis, disengage
the gearing mechanism by pulling out the engagement
knob (1) and at the same time pivot the position
adjustment knob (2) back toward the hip. The hinge
should move freely.
4
3
2
1
5
1. Sizing and Molding
the Thigh and Calf
Cuffs: Trim the panels
of the middle thigh
cuff (3) equally from
each side so the cuffs
do not overlap when on the patient. Trim the calf cuff
(4) so the sides of the cuff do not overlap when on
the patient. Note: The blue foam liner should extend
1
/ " beyond the white Wire-Foam ™ . Mold the cuffs
2
around the patient's thigh and calf.
Model #4405
Static-Pro ® Knee
Static Progressive Orthosis
Single Patient Use Only
Rx Only
IMPORTANT
Please read all instructions, warnings and precautions
before use.
INTENDED USE
The DeRoyal Static-Pro ® Knee Orthosis is designed for
the treatment of joint stiffness and established soft
tissue contractures, which may have resulted from
trauma, immobilization or neurological disorders. The
orthosis should only be used under the supervision of a
qualified health care professional. Protocols for use
vary depending on the diagnosis and should be
determined after consulting with the patient's physician.
The Static-Pro ® Knee assists in either flexion or
extension in one unit.
CONTRAINDICATIONS
The Static-Pro ® Knee Orthosis should not be used if
any of the following conditions exist: Severe spasticity,
5
severe osteoporosis and/or thrombophlebitis. If pain,
numbness, swelling or skin irritation occurs while
wearing the orthosis, it should be removed. The
patient should be re-evaluated and appropriate
adjustments made.
PRECAUTION
1
Caution should be used if any of these conditions exist:
peripheral vascular disease, healing skin wounds, mild
spasticity, heterotrophic ossification and mild osteoporosis.
Be careful not to apply excessive tension to patients
with decreased sensation or feeling in the knee or leg.
INSTRUCTIONS FOR USE
CAUTION: The DeRoyal Static-Pro ® Knee Orthosis is a
non-ambulation orthosis. The intended use is for the
patient to be in a sitting or supine position. Ambulating
while wearing the orthosis may cause it to migrate
down the leg, making the unit ineffective.
IMPORTANT: Before applying the orthosis, disengage
the gearing mechanism by pulling out the engagement
knob (1) and at the same time pivot the position
adjustment knob (2) back toward the hip. The hinge
should move freely.
4
3
2
1
5
1. Sizing and Molding
the Thigh and Calf
Cuffs: Trim the panels
of the middle thigh
cuff (3) equally from
each side so the cuffs
do not overlap when on the patient. Trim the calf cuff
(4) so the sides of the cuff do not overlap when on
the patient. Note: The blue foam liner should extend
1
/ " beyond the white Wire-Foam ™ . Mold the cuffs
2
around the patient's thigh and calf.
5
1