Mitsubishi Electric GT21-03SDCD General Description

JY997D62001D
Side
ENGLISH
A
Side
CHINESE
B
GT21-03SDCD
GT21-03SDCD General Description
Manual Number JY997D62001D
Date April 2018
This manual describes the part names, dimensions, mounting, and specifications
of the product. Before use, read this manual and manuals of relevant products
fully to acquire proficiency in handling and operating the product. Make sure to
learn all the product information, safety information, and precautions.
And, store this manual in a safe place so that you can take it out and read it
whenever necessary. Always forward it to the end user.
Registration
The company name and the product name to be described in this manual are the
registered trademarks or trademarks of each company.
Effective April 2018
Specifications are subject to change without notice.

2014 MITSUBISHI ELECTRIC CORPORATION
Safety Precaution
(Read these precautions before using.)
Before using this product, please read this manual and the relevant manuals
introduced in this manual carefully and pay full attention to safety to handle the
product correctly.
The precautions given in this manual are concerned with this product.
In this manual, the safety precautions are ranked as "WARNING" and
"CAUTION".
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or slight personal injury
or physical damage.
Depending on circumstances, procedures indicated by "CAUTION" may also be
linked to serious results. In any case, it is important to follow the directions for
usage.
MOUNTING PRECAUTIONS
 Use the SD card unit in the environment that satisfies the general
specifications described in this manual. Not doing so can cause an electric
shock, fire, malfunction or product damage or deterioration.
 When mounting the SD card unit to the GOT, mount it on the side of the GOT,
and tighten the tapping screws in the specified torque range (0.3 N•m to 0.6
N•m) with a screwdriver.
Undertightening can cause the GOT to drop, failure or malfunction.
Overtightening can cause a drop, failure or malfunction due to the damage of
the screws or the GOT.
 Be sure to shut off all phases of the external power supply used by the
system before mounting or removing the SD card unit to/from the GOT. Not
doing so can cause the unit to fail or malfunction.
OPERATION
PRECAUTIONS
 Securely connect the SD card unit to the specified connector in the GOT
while the GOT is turned OFF.
Connection failure may cause malfunction.
 Before touching the SD card unit, always touch grounded metals, etc. to
discharge static electricity from human body, etc. Not doing so can cause the
unit to fail or malfunction.
DISPOSAL PRECAUTIONS
 When disposing of this product, treat it as industrial waste.
Side
A
PRECAUTIONS WHEN THE
DATA STORAGE IS IN USE
 If the SD card mounted on drive A of the GOT is removed while the GOT is
accessed, processing for the GOT might be interrupted about for 20 seconds. The
GOT cannot be operated during this period. The functions that run in the
background including a screen updating, alarm, logging, scripts, and others are
also interrupted. Since this interruption makes an impact to the system operation,
it might cause failure. After inhibiting access to the SD card on the GOT utility
screen, check that the SD card access LED is off and remove the SD card.
PRECAUTIONS WHEN THE
DATA STORAGE IS IN USE
 If the data storage mounted on the GOT is removed while the GOT is accessed,
the data storage and files are damaged. To remove the data storage from the
GOT, check that the access to the data storage in SD card access LED, the
system signal, and others is not performed.
 If the GOT is turned OFF while it is accessing the SD card, the SD card or file may
be damaged.
 When removing the SD card from the GOT, make sure to support the SD card by
hand as it may pop out. Failure to do so may cause the SD card to drop from the
GOT, resulting in a failure or break.
 Before removing the USB device from the GOT, follow the procedure for removal
on the utility screen of the GOT. After the successful completion dialog is
displayed, remove the USB device by hand carefully. Failure to do so may cause
the USB device to drop from the GOT, resulting in a failure or break.
Manual
The following shows manuals relevant to this product.
Detailed Manual
Manual name
GOT2000 Series User's Manual (Hardware) SH-081194ENG-A (1D7MJ5)
GOT2000 Series User's Manual (Utility) SH-081195ENG-A (1D7MJ6)
For detailed manuals, refer to the PDF manuals stored in the DVD-ROM for the
drawing software used.
Relevant Manuals
For relevant manuals, refer to the Help or the PDF manuals stored in the DVD-ROM for
the drawing software used.
The latest manuals are also available from MITSUBISHI ELECTRIC FA Global Website
(http://www.MitsubishiElectric.co.jp/fa).
Before using the GOT
Connect the connector of the GOT to the connector of the battery.
Refer to the GOT2000 Series User's Manual (Hardware) for the connection
instructions.
For details on the GOT specifications, installing instructions, wiring, maintenance and
inspection, or checking procedure for the version and the compatible standard, refer to
the GOT2000 Series User's Manual (Hardware).
Referenced Standard: GB/T15969.2 (Requirement of Chinese standardized law)
1. FEATURES
The SD card unit is used to mount the SD card to the GOT main unit.
1.1 Bundled Items
Bundled item
M38 tapping screws for the GOT installation: 2 pcs.
GT21-03SDCD General Description (This manual)
2. Part Names and External Dimensions
2)
53(2.09")
3)
Number Name
Connector for mounting to the
1)
GOT
2) SD card access LED
3) Mounting fitting
3. Specifications
3.1 General Specifications
Item
Manual number
Operating ambient temperature
(Model code)
Input power supply voltage
Other specifications are same as those of the GOT main unit.
Refer to the following.
4. Mounting
1) Remove the cover of the GOT.
2) Connect the GOT connector of the SD card unit to
the connector in the GOT main unit.
Quantity
2
1
3) Fix the SD card unit with the tapping screws offered
as accessories.
Tightening torque: 0.3 to 0.6 N•m
5(0.20")
15(0.59")
1)
Unit:mm(inches)
Description
-
ON: SD card installed
OFF: SD card not installed or SD card
installed but removal possible
Direct mounting hole
Specifications
0 °C to 55 °C
3.3 V (Supplied from GT2103 models)
GOT2000 Series User's Manual
This manual confers no industrial property rights or any rights of any other
kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation
cannot be held responsible for any problems involving industrial property rights
which may occur as a result of using the contents noted in this manual.
Warranty
Exclusion of loss in opportunity and secondary loss from warranty liability
Regardless of the gratis warranty term, Mitsubishi shall not be liable for
compensation to:
(1) Damages caused by any cause found not to be the responsibility of
Mitsubishi.
(2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi
products.
(3) Special damages and secondary damages whether foreseeable or not,
compensation for accidents, and compensation for damages to products
other than Mitsubishi products.
(4) Replacement by the user, maintenance of on-site equipment, start-up test run
and other tasks.
 This product has been manufactured as a general-purpose part for general
industries, and has not been designed or manufactured to be incorporated in
a device or system used in purposes related to human life.

Before using the product for special purposes such as nuclear power, electric
power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
 This product has been manufactured under strict quality control. However
when installing the product where major accidents or losses could occur if the
product fails, install appropriate backup or failsafe functions in the system.
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
For safe use