Related Manuals for NemaVision-iPC NVHMI-707
Summary of Contents for NemaVision-iPC NVHMI-707
- Page 1 NVHMI-7 SERIES User Manual Release Date Revision Apr. 2013 V1.0 NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 2: Warning
This information in this document is subject to change without notice. In no event shall Nemavision-iPC/Aplex Technology Inc. be liable for damages of any kind, whether incidental or consequential, arising from either the use or misuse of information in this document or in any related materials. -
Page 3: Packing List
Always disconnect power when the system is not in use. Disconnect power when you change any hardware devices. For instance, when you connect a jumper or install any cards, a surge of power may damage the electronic components or the whole system. NVHMI SERIES User Manual www.nemavision-ipc.com... -
Page 4: Table Of Contents
4.2 Intel Graphics Media Accelerator Driver...……………………………..57 4.3 Intel (R) Network Adapter……..………………………………………….60 4.4 Realtek ALC662 HD Audio Driver Installation…….………….…………62 Chapter 5 Touch Screen Installation 5.2 Windows 2000/XP USB Driver Installation for PenMount 6000Series.64 5.1.1 Installing Software (Resistive Touch)..........64 NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 5 Figure 1.2:Dimensions of NVHMI-708…………………………………..…..8 Figure 1.3:Dimensions of NVHMI-712…………………………………….8 Figure 1.3:Dimensions of NVHMI-715…………………………………….9 Figure 1.4: Front View of NVHMI SERIES………………………………...10 Figure 1.5: Rear View of NVHMI-707/NVHMI-708……………………..10 Figure 1.5: Rear View of NVHMI-712/NVHMI-715……………………..11 Figure 2.1: Mainboard Dimensions…………………………………..……..17 Figure 2.2: Jumpers and Connectors Location_ Board Top………………...18 Figure 2.3: Jumpers and Connectors Location_ Board Bottom…………..19...
-
Page 6: Specifications
Chapter 1 System 1.1 Specifications NVHMI-707(P) NVHMI-708(P) NVHMI-712(P) NVHMI-715(P) System Intel Atom Cedar View N2600 1.6GHz Dual Core Processors System Chipset Intel NM10 System Memory Onboard DDR3 2GB 800 MHz IO Port 2 x USB 2.0 type A, USB4/5 Serial/Parallel... -
Page 7: Dimensions
Embedded Windows Embedded standard 7(Win 7 support 3D Graphic function) System Support Note 1: NVHMI series is covered by one or more of the following patents: US6, 570, 884, US6,115,776, and US6,327,625. 1.2 Dimensions Figure 1.1: Dimensions of NVHMI-707 NVHMI SERIES User Manual www.nemavision-ipc.com... -
Page 8: Figure 1.2:Dimensions Of Nvhmi-708
Figure 1.2: Dimensions of NVHMI-708 Figure 1.3: Dimensions of NVHMI-712 NVHMI SERIES User Manual www.nemavision-ipc.com... -
Page 9: Figure 1.3:Dimensions Of Nvhmi-715
Figure 1.4: Dimensions of NVHMI-715 NVHMI SERIES User Manual www.nemavision-ipc.com... -
Page 10: Brief Description
Optional projected capacitive touchscreen support 7H anti-scratch surface is ideal for use as a PC-based controller for Industrial Automation & Factory Automation. Figure 1.5: Front View of NVHMI SERIES Figure 1.6: Rear View of NVHMI -707/NVHMI -708 NVHMI SERIES User Manual www.nemavision-ipc.com... -
Page 11: Installation Of Hdd
Figure 1.7: Rear View of NVHMI -712/ NVHMI- 715 1.4 Installation of HDD(NVHMI-707/NVHMI-708) Step 1 There are 2 screws to deal with when enclosing or removing the chassis. Gently remove 2 screws. Step 2 There is a SSD card in the bracket. Gently remove the screw, then carefully pull SSD card. - Page 12 Note: 4 screws are packed in the packing list. Step 5 There is a SD card hole in the side of the machine. You can replace SD card from there. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 13 Step 6. Gently screw the screws. Installation of HDD(NVHMI-712 / NVHMI-715) Step 1 There are 2 screws to deal with when enclosing or removing the chassis. Gently remove 2 screws. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 14 You can remove HDD by unscrewing 4 screws in the HDD bracket. Note: 4 screws are packed in the packing package. Step 4 There is a SD hole in the side of machine. You can replace SD card from there NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 15: Chapter 2 Hardware
1 x RS232 port, DB9 connector for external (COM2) pin 9 w/5V/12V/Ring select 1 x RS422/485 header via CN2 (COM3) 2 x UART via CN3 (COM5,COM6) 8-bit digital I/O Pin header via CN2 Digital I/O NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 16 Software programmable 1 – 255 second by Super I/O Timer Operating: -20 to 70 Temperature Storage: -40 to 85 Humidity 5% - 95%, non-condensing, operating Power 12V /0.95A (Intel Atom N2600 processor with 2GB DDR3 Consumption DRAM) EMI/EMS Meet CE/FCC class A NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 17: Figure 2.1: Mainboard Dimensions
(units :mm) Figure 2.1: Mainboard Dimensions NVHMI SERIES User Manual www.nemavision-ipc.com... -
Page 18: Installations
LVDS interface. To satisfy the special needs of high-end customers, CN1 and CN2 and CN3 richer extension functions. The product is widely used in various sectors of industrial control. 2.2.1 Jumpers Setting and Connectors Board Top Figure 2.2: Jumpers and Connectors Location_ Board Top Board Bottom NVHMI SERIES User Manual www.nemavision-ipc.com... -
Page 19: Jumpers Setting And Connectors
Figure 2.3: Jumpers and Connectors Location_ Board Bottom 2.3 Jumpers Setting and Connectors 1. JP5: (2.0mm Pitch 1X2 box Pin Header),ATX Power and Auto Power on jumper setting. Mode Open ATX Power Close Auto Power on (Default) NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 20 6. VGA1: (CRT 2.0mm Pitch 2X6 Pin Header), Video Graphic Array Port, Provide 2x6Pin cable to VGA Port. Signal Name Pin# Pin# Signal Name CRT_RED Ground CRT_GREEN Ground CRT_BLUE Ground CRT_H_SYN CRT_DDCDAT CRT_V_SYNC CRT_DDCCL Ground Ground NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 21 (Switch),COM1 setting, it provides selectable RS232 or RS422 or RS485 serial signal output. Function RS_422 Pin# RS232 OFF: Pin1, Pin2, Pin3, Pin4 (Default) RS422 Pin1, Pin2, Pin3, Pin4 (option) RS485 Pin1, Pin2, Pin3, Pin4 (option) Note: Must keep the setting with BIOS setting. NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 22: Chapter 3 Bios Setup
CTS (Clear To Send) JP1 select Setting (RI/5V/12V) BIOS Setup Advanced/W83627UHG Super IO Configuration/Serial Port 1 Configuration RS-232 RS422 (option): Pin# Signal Name 422_RX+ 422_RX- 422_TX- 422_TX+ Ground BIOS Setup Advanced/W83627UHG Super IO Configuration/Serial Port 1 Configuration RS-422 NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 23 (2.0mm Pitch 2x3 Pin Header), COM2 jumper setting, pin 1~6 are used to select signal out of pin 9 of COM2 port. JP2 Pin# Function Close 1-2 COM1 RI (Ring Indicator) (default) Close 3-4 COM1 Pin9=+5V (option) Close 5-6 COM1 Pin9=+12V (option) NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 24 16. LED3: LED STATUS. Green LED for Touch Power status. 19 SATA1: SATA Connectors, one SATA connectors are provided, with transfer (SATA 7Pin+15Pin), speed up to 3.0Gb/s. 20 SD1: (SD card socket),Secure Digital Memory Card socket. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 25 ACTIVE LED (yellow) respectively located at the left-hand and right-hand side of the Ethernet port indicate the activity and transmission state of LAN. 26. BUZ1: Onboard buzzer. 27 LED1: LED STATUS. Green LED for Motherboard Power status. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 26 DSRCOM5_RTS- COM5_DSR DTRCOM5_CTS- GPIO24 ICH_GPIO24 ICH_GPIO13 GPIO13 GPIO26 ICH_GPIO26 ICH_GPIO27 GPIO27 Ground Ground PE1_TX_N0 PE1_TX_P0 PE1_RX_N0 PE1_RX_P0 PCIE PCIE Ground Ground CLK_100M_PE1_P CLK_100M_PE1_N PLTRST_BUF- PM_PCIE_WAKE SMBUS SMB_CLK_S SMB_DATA_S SMBUS PE1_CLKRE Ground PCIE PCIE 3P3V_S5 3P3V_S5 NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 27 3P3V_S5 3P3V_S5 12V_S0 12V_S0 NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 28: Operations After Post Screen
Press DEL or F2 to enter setup After optimizing and exiting CMOS Setup, the POST screen displayed for the first time is as follows and includes basic information on BIOS, CPU, memory, and storage devices. NVHMI SERIES User Manual www.nemavision-ipc.com... -
Page 29: Bios Setup Utility
3.3 Main Settings BIOS Information Intel Reference Code BIOS Vendor American Megatrends Version Core Version 4.6.5.3 Compliancy UEFI 2.3; PI 1.2 Project Version 7106V002 Build Date and Time 12 17 2012 03:22:46 ►Intel RC Version NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 30 Second : 0 to 59 System Date: Set the system date, the date format is: Note that the ‘Day’ automatically changes when you set the date. Day: Month: 01 to 12 Date: 01 to 31 Year: 1998 to 2099 NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 31: Advanced Settings
[64 PCI Bus Clocks] [96 PCI Bus Clocks] [128 PCI Bus Clocks] [160 PCI Bus Clocks] [192 PCI Bus Clocks] [224 PCI Bus Clocks] [248 PCI Bus Clocks] VGA Palette Snoop: [Disabled] [Enabled] PERR# Generation: NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 32 [Enabled] 3.4.3 CPU Configuration Processor Type Intel(R) Atom(TM) CPU N2600 EMT64 Not Supported Processor Speed 1600 MHz System Bus Speed 400MHz Ratio Status Actual Ratio System Bus Speed 400 MHz Processor Stepping 30661 Microcode Revision NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 33 Active Trip Point Hi [71C] Passive Trip Point [95] Passive TC1 Value Passive TC2 Value Passive TSP Value 3.4.5 IDE Configuration SATA Port0 Not Present SATA Port1 Not Present SATA Controller(S): [Enabled] [Disabled] Configure SATA as: [IDE] NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 34 Device power-up delay [Auto] [Manual] Mass Storage Devices Multiplecard Reader 1 [Auto] [Floppy] [Forced FDD] [Hard Disk] [CD-ROM] 3.4.7 W83627UHG Super IO Configuration W83627UHG Super IO ch W83627UHG Serial Port 1 Configuration UART Mode Selection [RS-232] NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 35 : +5.216 V VSB5 : +5.203 V VBAT : +3.334 V 3.4.9 Serial Port Console Redirection COM0 Console Redirection [Enabled] [Disabled] Console Redirection Settings Serial Port for Out-of-Band Management/ Windows Emergency Management Services (EMS) Console Redirection NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 36 CPU C state Report [Enabled] [Disabled] Enhanced C state [Enabled] [Disabled] CPU Hard C4E [Enabled] [Disabled] CPU C6 state [Enabled] [Disabled] C4 Exit Timing [Fast] [Default] [Slow] C-state POPDOWN [Enabled] [Disabled] C-state POPUP [Enabled] [Disabled] NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 37: Chipset Settings
►Intel IGD Configuration ******* Memory Information ******* Memory Frequency 800 MHz(DDR3) Tot al Memory 2048 MB DIMM#0 Not Present DIMM#1 2048 MB Memory Frequency and Timing MRC Fast Boot [Enabled] [Disabled] Max TOLUD [Dynamic] [1GB] [1.25GB] NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 38 [1024x768 18bit ] [1280x768 18bit ] [1280x800 18bit ] [1280x1024 18bit] [1366x768 18bit] [1024x768 24bit] [1280x768 24bit] [1280x800 24bit] [1280x1024 24bit] Panel Scaling [Auto] [Force Scaling] [off] [Maintain Aspect Ratio] Active LFP [LVDS] [No LVDS] [EDP] NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 39 Back light Control Lev [Auto] [Disabled] [Level 8] [Level 1] [Level 2] [Level 3] [Level 4] [Level 5] [Level 6] [Level 7] [Level 8] [Level 9] [Level 10] [Level 11] [Level 12] [Level 13] [Level 14] [Level 15] NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 40 PCI-Exp. High Priorit [Disabled] [Enabled] High Precision Event Timer Configuration High Precision Timer [Enabled] [Disabled] SLP_S4 Assertion Widt [1-2 Seconds] [2-3 Seconds] [3-4 Seconds] [4-5 Seconds] Restore AC Power Loss [Last State] [Power off] [Power on] NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 41: Boot Settings
Boot Option #2 […] F3:Optimized Defaults Hard Drive BBS Priorities F4:Save and Exit ►CSM Parameters ESC Exit Version 2.15.1226. Copyright (C) 2012 American Megatrends , Inc. Setup Prompt Timeout Bootup Numlock State [On] [off] Quiet Boot [Disabled] NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 42 Interrupt 19 Capture [Immediate] [Postponed] Boot Option #1 Boot Option #2 …… Sets the system boot order [SATA PM:*** … ] Hard Drive BBS Priorities Boot Option #1 SATA PM:***… ****** Disabled CSM Parameters Launch CSM [Always] NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 43 [Do not Launch] [UEFI only] [Legacy only] Launch Storage OpROM [Legacy only] [Do not Launch] [UEFI only] Launch Video OpROM po [Do not Launch] [UEFI only] [Legacy only] Other PCI device ROM [UEFI OpROM] [Legacy OpROM] NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 44: Security Settings
Enter key. You may press Esc key to abandon password entry operation. To clear the password, just press Enter key when password input window pops up. A confirmation message will be shown on the screen as to whether the password will be disabled. NVHMI SERIES User Manual www.nemavision-ipc.com... -
Page 45: Save And Exist Settings
Note: Due to limited address length of BIOS, only a portion of panel parameters are listed in BIOS Setup. If the connected panel is not included in the parameter list, display problem will occur. In this case, Please do not change BIOS setup. NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 46 V02.61 © Copyright 1985-2006 American Mega trends , Inc. Memory Remap Feature: [Enabled] [Disabled] Memory Hole: [Disabled] [15MB-16MB] Initate Graphic Adapter: Select which graphics controller to use as the primary boot device. [IGD] [PCI/IGD] IGD Graphics Mode Select: [Enabled, 64MB] [Disabled] NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 47 F10 Save and Exit Backlight Image Adaptation ESC Exit [VBIOS-Default] V02.61 © Copyright 1985-2006 American Mega trends , Inc. DVMT Mode Select: [DVMT Mode] [FIXED Mode] DVMT/FIXED Memory Size: [256MB] [128MB] [Maximum DVMT] Boot Display Device: [BIOS-Default] [CRT] NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 48 Backlight Control Control: [Level5] [Level0] [Level1] [Level2] [Level3] [Level4] [Level6] [Level7] Note: Panel support PWM Function. Backlight Control Mode: [DC] [PWM] Backlight Image Adaptation: [VBIOS-Default] [BIA Disabled] [BIA Enabled at Level1] [BIA Enabled at Level2] NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 49 Save & Exit Setup save Configuration and exit ? [Yes] [No] Discard Changes and Ext Exit Without Saving Quit without saving? [Yes] [No] Save Changes and Reset Save & reset Save Configuration and reset? [Yes] NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 50 [Yes] [No] Save user Defaults Save Values as User Defaults Save configuration? [Yes] [No] Restore user Defaults Restore User Defaults Restore User Defaults? [Yes] [No] Launch EFI Shell from filesystem device WARNING Not Found [ok] NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 51: Exit Options
[OK] [Cancel] Discard Changes and Exit: Discard Changes and Exit setup? ESC key can be used for this operation) [OK] [Cancel] Discard Changes: Discard changes? F7 key can be used for this operation) [OK] [Cancel] NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 52 Load Optimized Defaults: Load Optimized Defaults? F9 key can be used for this operation) [OK] [Cancel] Load Fail-Safe Defaults: Load Fail-Safe Defaults? F9 key can be used for this operation) [OK] [Cancel] NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 53: Chapter 4 Installation Of Drivers
VGA driver, LAN drivers, Audio driver Installation instructions are given below. Important Note: After installing your Windows operating system (Windows XP), you must install first the Intel Chipset Software Installation Utility before proceeding with the installation of drivers. NVHMI SERIES User Manual www.nemavision-ipc.com... -
Page 54: Intel Chipset Driver
4.1 Intel Chipset Driver To install the Intel chipset driver, please follow the steps below. Step 1. Select Intel (R) Chipset NM10 Express from the list Step 2. Click Next to setup program. NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 55 Step 3. Read the license agreement. Click Yes to accept all of the terms of the license agreement. Step 4. Click Next to continue. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 56 Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. Click Finish, then remove any installation media from the drives. NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 57: Intel Graphics Media Accelerator Driver
4.2 Intel Graphics Media Accelerator driver To install the VGA drivers, follow the steps below to proceed with the installation. Step 1.Select Intel(R) VGA Chipset Driver. Step 2. Select Installs driver and application files. Click Next. NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 58 Step 3. Select I agree. Click Install. Step 4. Click Continue Anyway. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 59 Step 5. Click Continue Anyway. Step 6. To restart the computer, click Yes. NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 60: Intel (R) Network Adapter
4.3 Intel (R) Network Adapter To install the Intel (R) Network Adapter device driver, please follow the steps below. Step 1. Select Realtek RTL8111D Driver. Step 2. Click Next to continue. NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 61 Step 3. Click Install to begin the installation. Step 4. Click Finish to exist the wizard. NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 62: Realtek Alc662 Hd Audio Driver Installation
4.4 Realtek ALC662 HD Audio Codec Driver Installation To install the Realtek ALC662 HD Audio Codec Driver, please follow the steps below. Step 1. Select Realtek AL662 Audio Codec Driver from the list Step 2. Click Next to continue. NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 63 Step 3. Click Yes, I want to restart my computer now. Click Finish to complete the installation. NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 64: Chapter 5 Touch Screen Installation
If you have an older version of the PenMount Windows 2000/XP driver installed in your system, please remove it first. Follow the steps below to install the PenMount DMC6000 Windows 2000/XP driver. Step 1. Insert the product CD, the screen below would appear. Click touch panel driver. NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 65 Step 2. Select Resistive Touch. Step 3. Click Next to continue. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 66 Step 4. Read the license agreement. Click I Agree to agree the license agreement. Step 5. Choose the folder in which to install PenMount Windows Universal Driver. Click Install to start the installation. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 67 Step 6. Wait for installation. Then click Next to continue. Step 7. Click Continue Anyway. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 68 Step 8. Click Finish to complete installation. NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 69: Installing Software (Projected Capacitive)
5.1.2 Installing Software (Projected Capacitive) Step 1. Insert the product CD, the screen below would appear. Click touch panel driver. Step 2. Select Projected Capacitive. NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 70 Step 3. Click Next to continue. Step 4. Select I accept the terms of the license agreement. Click Next. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 71 Step 5. Tick Install RS232 interface driver. Click Next. Step 6. Select None. Click Next. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 72 Step 7. Click OK. Step 8. Tick Support Muti-Monitor System. Click Next. Step 9. Go to C:\Program Files\eGalaxTouch. Click Next. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 73 Step 10. Click Next. Step 11. Tick Create a eGalaxTouch Utility shortcut on desktop. Click Next. NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 74: Software Functions(Resistive Touch)
2. When the PenMount Control Panel appears, select a device to “Calibrate.” PenMount Control Panel(Resistive Touch) The functions of the PenMount Control Panel are Device, Multiple Monitors ,Tools and About, which are explained in the following sections. NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 75 Advanced Calibration uses 4, 9, 16 or 25 points to effectively calibrate touch panel linearity of aged touch screens. Click this button and touch the red squares in sequence with a stylus. To skip, press ESC’. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 76 Dmcctrl.exe - calibration ($) 0= Standard Calibration 4=Advanced Calibration 4 9=Advanced Calibration 9 16=Advanced Calibration 16 25=Advanced Calibration 25 Step 1. Please select a device then click “Configure”. You can also double click the device too. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 77 Step 2.Click “Standard Calibration” to start calibration procedure NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an accurate calibration. Use a stylus during Advanced Calibration for greater accuracy. Please follow the step as below: NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 78 Step 3.Come back to “PenMount Control Panel” and select Tools then click Advanced Calibration. Step 4. Select Device to calibrate, then you can start to do Advanced Calibration. NOTE: Recommend to use a stylus during Advanced Calibration for greater accuracy. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 79 Setting NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 80 About This panel displays information about the PenMount controller and driver version. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 81 Please note once you turn on this function the rotating function is disabled. Enable the multiple display function as follows: 1. Check the Enable Multiple Monitor Support box; then click Map Touch Screens to assign touch controllers to displays. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 82 4. Touching all screens completes the mapping and the desktop reappears on the monitors. 5. Select a display and execute the “Calibration” function. A message to start calibration appears. Click OK. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 83 This panel displays information about the PenMount controller and this driver version. PenMount Monitor Menu Icon The PenMount monitor icon (PM) appears in the menu bar of Windows 2000/XP system when you turn on PenMount Monitor in PenMount Utilities. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 84 2. Choose the rotate function (0°, 90°, 180°, 270°) in the 3rd party software. The calibration screen appears automatically. Touch this point and rotation is mapped. NOTE: The Rotate function is disabled if you use Monitor Mapping NVHMI SERIES User Manual www.nemavision-ipc.com...
-
Page 85: Software Functions(Projected Capacitive)
5.2.2 Software Functions(Projected Capacitive) General In this window, you can see there is USB Controller. Click OK to continue. Monitor Mapping to adjust touch panel to seNVh for device NVHMI SERIES User Manual www.nemavision-ipc.com... - Page 86 Beep On Touch Beep On Release Beep From System Beep Beep From Sound Card Linearization Style 9 points 25 points Double Click Time Shorter Longer Double Click Area Smaller Bigger Normal mode Simulate the mouse mode NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 87 Option Function Enable Constant Touch Enable Auto Right Click Enable Touch Enable Cursor Stabilization Constant Touch Area Auto Right Click Time NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 88 Do 4 points alignment to match display. Clear and Calibrate Clear linearization parameter and do 4 points alignment. Linearization Do 9 points linearization for better touchscreen linearity. Draw Test Do draw test to verify the touch accuracy. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 89 Display In this window, it shows the mode of display. Enable Multiple Monitors. Map to main display if system has only one display monitor Full Screen Lower Screen Left Screen Upper Screen Right Screen NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 90 Other Other mode of display. Quarter1~4 and Customized area. Active Area Drag active area to enable Active Area Function. NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 91 Hardware Saturn Hardware Configuration NVHMI SERIES User Manual www.nemavision-ipc.com...
- Page 92 About To display information about eGalaxTouch and its version. NVHMI SERIES User Manual www.nemavision-ipc.com...