Optelecom 9000 series, four channel option module host multiplexer/demultiplexer, for adding the capability to transport up to four option module channels via the hs data ports of a compatible optelecom fiber optic multiplexer
Page 1
Optelecom 9000 Series Installation and Operation Manual Model 9961A-C Four Channel Option Module Host Multiplexer/Demultiplexer For adding the capability to transport up to four Option Module channels via the HS Data Ports of a compatible Optelecom fiber optic multiplexer UM50175, Manual 9555, Rev. E...
Safety Instructions Instrucciones de Seguridad Sicherheitsanleitungen Consignes de Sécurité Functional Description 9961A-C Indicator, Connector, and Switch Location and Function 9961A-C Configuration and Connection Guide Operation of the 9961A-C Operation of the 9961A-C with Network Management System Software Specifications for the 9961A-C...
Safety Instructions SA-1 The safety information contained in this section, and on other pages of this manual, must be observed whenever this unit is operated, serviced, or repaired. Failure to comply with any precaution, warning, or instruction noted in the manual is in violation of the standards of design, manufacture, and intended use of the unit.
Instrucciones de Seguridad SA-1 Debe observarse la información de seguridad contenida en esta sección, y en otras páginas de este manual siempre que se opere, dé servicio o repare esta unidad. Si no se cumple con alguna precaución, advertencia o instrucción indicada en este manual se infringen los estándares de diseño, fabricación y el uso destinado a la unidad.
Sicherheitsanleitungen SA-1 Die in diesem abschnitt und auf anderen seiten dieses Handbuchs enthaltenen Sicherheitsinformationen müssen befolgt werden, wenn diese einheit betrieben, gewartet oder repariert wird. Falls Vorsichtsmassnahmen, Warnungen oder Anweisungen in diesem Handbuch nicht befolgt werden, verstösst dies gegen die Konstruktions, und Herstellungsstandards und erfolgt im gegensatz zum vorgesehenen Verwendungszweck dieser einheit.
Consignes de Sécurité SA-1 Les consignes de sécurité contenues dans cette section et dans le reste de ce manuel doivent être respectées a chaque fois que cet appareil est utilisé ou fait l’objêt d’une maintenance ou d’une réparation. Le non-respect d’une précaution, d’un avertissement ou d’une instruction figurant dans ce manuel est une violation des normes de conception, fabrication et indication d’usage de l’appareil.
Refer to the separate Option Module manual for details on Option Module operation. The Model 9961A-C is a rack-mount, plug-in card that occupies a single slot in a Series 9000 card chassis. It operates on 6VDC from the chassis power supply.
S1-7 is ON and S1-8 is OFF. HS DATA PORT This RJ45 port is the physical interface for the high speed composite data and clock signals that travel between the 9961A-C and the HS port of the fiber optic multiplexer via Category 5 twisted pair cable.
Page 10
4-7. OPTION MODULE INTERFACE LOCATIONS Up to four option modules are installed here. DIPSWITCH S1 These switches modify the operation of the LED indicators and the Tx CLOCK/DATA phasing. Refer to the 9961A-C Connection and Configuration Guide on page 4.
ONFIGURATION Set the eight-position dipswitch on the 9961A-C per Table 1. Switch 3 may be set to the ON position when using a Cat 5 cable with a length of longer than 1 meter and marginal operation is observed. Switch settings 7 and 8 affect only the operation of the LEDs and will not affect operation of the cards.
Page 12
Note: If cables other than those supplied are used, they should be shielded Cat 5 cables. If the cable length exceeds 1 meter and improper operation is observed, set switch 3 to the ON (DOWN) position. This adjusts the timing of the clock circuits to allow for longer cable lengths. The Option Module position (1 to 4) at one end of the link is electronically mated to the SAME Option Module position at the other end of the link 1 to 1, 2 to 2, and so on.
Operation of the 9961A-C with Network Management System Software Operation of the 9961A-C with the Network Management System consists of the following parameters: Card Location Card Size (Number of Slots) Card Name (Model Number)
Specifications for the 9961A-C COMPOSITE Interface RS422 Clock and Data, Full Duplex Data Rate 15 Mbps or 16 Mbps depending on host card high-speed port clock rate Connector RJ 45, Category 5 Cable, 4 pair SUBCHANNELS Data Rate DC to 115.2 kbps Data Sampling Rate 1.5 mHz or 1.6 mHz depending on host card high-speed port...
Need help?
Do you have a question about the 9961A-C and is the answer not in the manual?
Questions and answers