Related Manuals for Beretta IDRA MS 200
Summary of Contents for Beretta IDRA MS 200
- Page 1 Installation and Operation Manual IDRA MS Solar | solar storage cylinder Installation and Operation Manual...
-
Page 3: Table Of Contents
RANGE MODEL CODE IDRA MS 200 BERETTA 20015324 IDRA MS 300 BERETTA 20015328 IDRA MS 430 BERETTA... -
Page 4: General
GENERAL GENERAL SAFETY INFORMATION PRECAUTIONS The operation of any appliance that uses electrical power Check that the product is complete, undamaged demands that a number of fundamental safety precautions and as ordered as soon as you receive it. Report any be respected. -
Page 5: Description Of The Appliance
IDENTIFICATION storage cylinders are identified by: IDRA MS Data plate This lists the technical specifications and performance of the product. Beretta Caldaie Via Risorgimento, 13 23900 Lecco (LC) T067659EPE02 INTERACUMULADOR SOLAR TERMOACUMULADOR SOLAR SOLAR STORAGE CYLINDER Modelo N°... -
Page 6: Technical Specifications
GENERAL TECHNICAL SPECIFICATIONS IDRA MS DESCRIPTION Type of storage cylinder Vitrified Storage cylinder layout Vertical Heat exchanger layout Vertical Storage cylinder capacity Diameter of storage cylinder with insulation Height with insulation 1330 1840 1630 1980 Insulation thickness Diameter/length of magnesium anode 33/450 33/520 Flange diameter... -
Page 7: Water Circuit
GENERAL WATER CIRCUIT TYPICAL WATER SYSTEM SCHEMATIC Solar regulator °C Water control system Solar collector Collector outlet Collector temperature sensor socket Collector return Manual bleed valve DHW recirculation pump Vent cock Solar collector circuit pump Vent valve Storage cylinder bottom temperature sensor Pressure gauge Collector probe Safety valve... -
Page 8: Location Of Sensors
GENERAL LOCATION OF SENSORS storage cylinders are equipped with dedicated sockets for the storage cylinder TEMPERATURE GAUGE IDRA MS or TEMPERATURE SENSOR. The installer is responsible for making all necessary connections to the boiler and solar collectors. Installers must use their expertise to ensure proper installation and functioning in compliance with all applicable legislation. -
Page 9: Overall Dimensions And Water Fittings
GENERAL OVERALL DIMENSIONS AND WATER FITTINGS IDRA MS 200 - 430 EAF (SB) (*) Hoses IDRA MS DESCRIPTION Domestic hot water outlet 1” F Ø Outlet from solar collector 1” M Ø Return to solar collector 1” M Ø DHW recirculation 3/4”... - Page 10 GENERAL 300 - 550 IDRA MS EAF (SB) (*) Hoses IDRA MS DESCRIPTION Domestic hot water outlet 1” F Ø Outlet from solar collector 1” M Ø Return to solar collector 1” M Ø DHW recirculation 3/4” F Ø EAF (SB) Domestic cold water inlet (storage cylinder drain) 1”...
-
Page 11: Installer
INSTALLER 10 UNPACKING THE PRODUCT If suitable equipment is not on hand to lift the storage cylinder off the pallet using the eyebolt, proceed as follows. - Place a platform of about half the height of the pallet storage cylinders are delivered in a single IDRA MS near the storage cylinder. -
Page 12: Technical Assistance Centre
TECHNICAL ASSISTANCE CENTRE 12 PLACE OF INSTALLATION 14 PUTTING INTO SERVICE storage cylinders can be installed in any It is essential to perform the following checks before IDRA MS room where there is no specific requirement for an electrical starting up or testing the functioning of the storage cylinder. protection rating higher than IP X0D. -
Page 13: Temporary Shutdown
TECHNICAL ASSISTANCE CENTRE 15 TEMPORARY SHUTDOWN 18 CLEANING AND REMOVING INTERNAL COMPONENTS If you are going away for a short period of time like a weekend or a short holiday, etc., and outdoor temperatures EXTERNAL CLEANING are going to remain above ZERO, proceed as follows. Clean the outside of the storage cylinder with a soft cloth - Adjust the storage cylinder thermostat to its minimum damped in soapy water. -
Page 14: Troubleshooting
TECHNICAL ASSISTANCE CENTRE 19 RECYCLING AND DISPOSAL Tighten the bolts (7), proceeding diagonally around the flange to apply pressure uniformly around the seal. At the end of its useful working life, do not abandon the storage cylinder in the environment, but dispose of it - Fill the storage cylinder’s DHW (secondary circuit) through the proper channels in accordance with applicable and check that there are no leaks from any of the... -
Page 15: End User
END USER END USER INSTRUCTIONS Refer to the GENERAL SAFETY INFORMATION and PRECAUTIONS section for safety-related information. 21 START-UP 22 TEMPORARY SHUTDOWN The storage cylinder must be put into service for the first To reduce impact on the environment and save energy, time by personnel from the manufacturer’s Technical before leaving for the weekend or a short break, etc., Assistance Centre. - Page 16 Commercial Offices: Via Risorgimento, 23 A 23900 - Lecco www.berettaboilers.com Beretta reserves the right to modify the characteristics and specifications given in this publication at any time and without prior notice as part of its policy of continuous product improvement.