Advertisement
DO NOT switch the sharpener on whilst the stone is in contact with the work piece.
8
DO NOT cover the sharpeners air vents situated beneath the motor. to do so will overheat the machine.
8
DO NOT touch the work piece immediately after sharpening as it will be hot.
8
DO NOT touch the sharpening stone/honing wheel whilst operating or whilst connected to the mains.
8
DO NOT leave the sharpener running unattended.
8
DO NOT operate the sharpener when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
1.2.12.
When not in use switch grinder off, remove plug from power supply.
2. ininTRODUCTION
fitted with induction motor suitable for workshop use, Ø200mm sharpening wet stone with detachable water trough, Ø200mm leather
horning wheel, grinding jig and angle guide. the sharpener is suitable for Hss tools.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SMS2101
motor Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180W
electrical supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V-50Hz
no load speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95rpm
Wet Wheel Dimensions: . . . . . . . . . . . . . . . Ø200 x 40mm x Ø12mm
Net Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.5kg
See fig.1
A .........................................................................Power cable
B ...................................................................... On/Off Switch
c ....................................................Detachable Water Trough
d ........................................................................... Wet Stone
e ..................................................... Cow Hide Honing Wheel
f ................................................................... Tool Rest/Clamp
G ..............................Adjustable Support for Tool Rest/Clamp
H ...................................................................... lifting Handle
4. ASSEMBLY
WARNING! Before assembly check to ensure grinder is unplugged from mains. Position on a flat surface with sufficient
‰
illumination
4.1.
Tool Rest
4.1.1.
fit adjustable support for tool rest fig.1G by unscrewing knobs and sliding rods into guides clamp in required position.
4.1.2.
side tool rest clamp fig.1f onto support.
4.2.
Water Reservoir
4.2.1.
Position water reservoir fig.1c by hooking on to main body of sharpener.
4.2.2.
ensure water reservoir is clear of rotating wheel.
4.2.3.
it is recommended to install the sharpener by mounting on a fireproof bench. use the mounting holes to secure to work surface.
Note:- the machine has no front or rear side so you can grind with or against the direction of wheel rotation. When positioning
please consider access to On/Off switch fig.1B .
4.2.4.
4.2.5.
5. GRINDING WHEELS
5.1.
MANDATORY SAFETY INSTRUCTIONS. (the following instructions must be observed together with those in section 1).
DANGER! Use of a damaged wheel (stone) is dangerous and may cause damage and/or personal injury.
▲
WARNING! ensure grinder is unplugged from mains supply before attempting to change grinding wheel (stone). only persons
‰
qualified under the "Abrasive Wheels Regulations" and holding a current grinding wheel certificate are authorised
to change and dress grinding wheels (stones).
Grinding wheels used with this machine must be of an adequate speed rating and suitable for the material to be ground.
9
ensure the maximum speed specification of the wheel is higher than that indicated on the machine data plate.
9
check that grinding wheels are secure and that wheels are not worn or damaged, that there are no fissures or cracks. if damaged
9
replace immediately.
ensure replacement wheel is not damaged in any way such as cracks, deformations or splinters etc. Also check the mounting flanges
9
for deformation, burrs or chips. Damaged flanges must Not be used as they may produce high stresses in the wheel causing it to
break. Do Not over tighten a wheel. Never tamper with a wheel in order to adapt it to a different size shaft.
Install a new wheel as in 5.2. Once mounted on the grinder test the wheel before use by facing the grinder in a safe direction (point it
9
away from yourself, others and vulnerable items) and run for a short time. Dress the wheel if necessary.
© Jack sealey limited
G
D
C
Fig.1
G
Original Language Version
F
sMS2101 | Issue 1
H
E
A
B
10/03/16
Advertisement
