Table of Contents
Advertisement
Quick Links
CSS 12 — Ozone/Salt Chlorinator
Prozone has combined ozone and salt together in one
Complete Sanitation System for your pool
Prozone Water Products: 3004 11th Ave - Huntsville, AL - 35805 Phone: 256-539-4570 Website: www.prozoneint.com
T . O
NATURAL TECHNOLOGY
3
Reduces Chemical Usage,
Improves Sanitation, Eliminates Odors
Produces Crystal Clear Water
Copyright 2007
202063
Advertisement
Table of Contents
Related Manuals for Prozone CSS 12
Summary of Contents for Prozone CSS 12
- Page 1 Complete Sanitation System for your pool T . O NATURAL TECHNOLOGY Reduces Chemical Usage, Improves Sanitation, Eliminates Odors Produces Crystal Clear Water Copyright 2007 Prozone Water Products: 3004 11th Ave - Huntsville, AL - 35805 Phone: 256-539-4570 Website: www.prozoneint.com 202063...
- Page 2 The CSS 12 must be installed in accordance with the installation instructions and diagrams provided in this manual. · The CSS 12 power supply must be mounted vertically on a flat surface and a minimum of 5 feet from the pool. ·...
-
Page 3: Table Of Contents
C S S 1 2 Table of Contents Page Section 1: Product Information 1.1 Recorded Information Sheets 4, 5 1.2 Introduction 1.3 Customer Responsibilites 1.4 How Does It Work Section 2: Installation 2.1 Installation Guidelines 2.2 Verify Contents 2.3 Quick Start Installation Guide 2.4 Saddle Clamp Installation Guide 2.5 Installation For New Pools 2.6 Connecting The Bypass Hoses... -
Page 4: Section 1: Product Information
C S S 1 2 Section 1 Product Information Record The Following Information and Save For Future Use Installer: Date of Installation: Control Box Control Box Model Number: CSS 12 Serial Number: Cell Cell Model Number Serial Number: Manufactured by Prozone Water Products 3004 11th Ave. -
Page 5: Introduction
Introduction Congratulations! You have purchased on of the most technologically advanced Pool Sanitation Systems in the world. The CSS 12 Ozone/Salt Chlorine Generator (Advanced Oxidation Processor ™) is the most powerful solution for Sanitation and Oxidation requirements in your pool, the benefits of which will be evident from the very first time you use it and for many years to come. -
Page 6: How Does It Work
The CSS 12 System provides the necessary chlorine residual for your pool. A measured amount of pool salt is dissolved in the pool water. The Chlorine is made by passing a very low voltage electric current through the salt water as it flows through the Cell and back in to the pool. -
Page 7: Section 2: Installation
Section 2 Product Installation Installation Guidelines ◊ The CSS 12 must be correctly installed or your system may not work properly and the warranty will be voided. ◊ The CSS 12 should be installed on residential pools only. ◊ A qualified swimming pool professional and certified electrician must install the CSS 12. -
Page 8: Quick Start Installation Guide
(Must be installed by a qualified electrician) · Your CSS 12 is a universal voltage system. It is preferable that this unit be wired so that it comes on when your circulation pump is running and off when pump is off. -
Page 9: Saddle Clamp Installation Guide
C S S 1 2 Section 2 Product Installation Installation Saddle Clamp Installation (for existing pools) Turn pool pump OFF. Locate section of existing plumbing in which you choose to install the entrance leg of the bypass. Location should be in any accessible area after the pump, before the filter. The vertical pipe coming from the pump outlet is recommended. Using a saddle clamp top as a guide, mark this spot. -
Page 10: Installation For New Pools
C S S 1 2 Section 2 Product Installation Installation for new pools (factory installation) Verify pool pump is turned off. First 2” PVC Tee should be installed after the pump but before the filter. 2” to 1-1/2” adapters are supplied if using 1-1/2”... -
Page 11: Standard Bypass Installation
C S S 1 2 Section 2 Product Installation Standard Bypass Installation $% & ' ( ) $% & ' ( ) ) ' + !'' " "... -
Page 12: Section 3: Pool Preparation
Your CSS 12 System comes supplied with a 0-10 SCFH air flow meter. This meter is used to properly setup the CSS system to guarantee sufficient air and water flow through the bypass. To test your system for air flow, verify CSS 12 is turned off. Turn pool pump on. Disconnect 1/4” hose from Injector port # 1. -
Page 13: Balance Pool Chemicals
Follow your pool builder’s suggestions on cure time allowance. You may run your new CSS 12 system without salt in the pool. It will not harm the system, but will not generate chlorine until salt has been added. -
Page 14: Section 4: Operation
C S S 1 2 Section 4 Operation System Operation The recommended run time to generate adequate amounts of chlorine is 12 hours per day. 8 hours continuously during the day; 4 more hours at night. Increased run times are recommended for highly loaded pools. The system will generate chlorine and ozone ONLY when the pool pump is running. After break point chlorination and as chlorine levels off at 1 ppm, run system for 48 hours or until the chlorine level stabilizes at 1 ppm. -
Page 15: Section 5: Chlorine Generator Cell Function & Maintenance
USE ONLY APPROVED CHLORINE CELL CLEANING SOLUTION OR CALCIUM-DISOLVING SOLUTION SUCH AS CLR Turn CSS 12 System and pool pump OFF and allow water to drain back out of the cell and bypass system. Disconnect the 3/4” system hose from the bottom of the chlorine generator cell. -
Page 16: Section 7: Warranty Information
The RGA number must be issued prior to end of warranty period. Product must be returned within 30 days of issuance of the RGA number. If the product is not received by Prozone within 30 days of RGA number issuance, another RGA number must be obtained; RGA number must be obtained before warranty period expires. -
Page 17: Warranty Registration Page
C S S 1 2 Section 7 Warranty Registration PLEASE COMPLETE THIS WARRANTY ON THE DAY OF INSTALLATION AND RETURN TO PROZONE WATER PRODUCTS INC. 3004 11TH AVE HUNTSVILLE, AL. 35805 Failure to return this warranty information will void this warranty. -
Page 18: Section 8: Trouble Shooting Guide
Dilute 10:1 with distilled water and test. Perform this test twice, once with the chlorine dial at 100% and again with the chlorine dial at 20%. Remove cap and reconnect 3/4” hose to bypass exit point fitting before restarting pool pump. If you still get no chlorine reading, contact a Prozone customer representative.
Need help?
Do you have a question about the CSS 12 and is the answer not in the manual?
Questions and answers