Advertisement
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/ or tie back long hair.
Keep children and unauthorised persons away from the working area.
DO NOT use equipment for any purpose other than that for which it is designed.
DO NOT operate the polisher/sander if any parts are damaged or missing as this may cause failure or possible personal injury.
WARNING! DO NOT sand any materials containing asbestos.
DO NOT switch the polisher/sander on whilst the head is in contact with the work piece and avoid unintentional starting.
DO NOT get the polisher/sander wet or use in damp or wet locations or areas where there is condensation.
DO NOT allow untrained persons to operate the polisher/sander.
DO NOT operate the polisher/sander when you are tired, under the influence of alcohol, drugs or intoxicating medication.
DO NOT use the polisher/sander where there are flammable liquids, solids or gases such as paint solvents, etc.
DO NOT leave the polisher/sander operating unattended.
DO NOT carry the polisher/sander with your finger on the power switch.
DO NOT pull the cord to remove the plug from the power supply.
Use a qualified person to lubricate and maintain the polisher/sander.
When not in use unplug from the mains power supply and store in a safe, dry, childproof area.
LEAD PAINT WARNING! Paint once contained lead as a traditional ingredient. Contact with the dust from the removal of such paint is toxic and
must therefore be avoided. The following action must be taken before using machine as a sander:
1.
User must determine potential hazard relating to age of paint to be removed. (Modern paints do not have lead content).
2.
DANGER! Keep all persons and pets away from the working area. The following are particularly vulnerable to the effects of lead paint
dust: Expectant women, babies and children.
3.
We recommend personal protection by using the following safety items:
A) Paint Spray Respirator (Sealey ref. SSP1699) B) PE Coated Hooded Coverall (Sealey ref. SSP266). C) Latex Gloves
(Sealey ref. SSP24).
4.
Take adequate measures to contain paint dust, flakes and scrapings. Wear safety equipment, as in (3) above and thoroughly clean
all areas when task is complete.
5.
Ensure the paint waste is disposed of in sealed bags or containers according to local regulations.
2. INTRODUCTION
Ergonomic design with comfortable soft grip handles. Variable speed control with 6 speed settings from 600 to 3200rpm make this suitable for
both sanding and polishing. Alloy bevel gear head with protective cover coupled to a composite motor housing. Soft start, constant speed motor
provides longer lasting performance. Carbon brush caps and mesh filters for simple maintenance. Supplied with Ø180mm backing pad, polishing
bonnet, D-Handle and side handle.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MS925PS
Pad Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ø180mm
Thread Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M14 x 2mm
No Load Speed:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600-3200rpm
Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1400W
Supply:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V
Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5kg
4. ASSEMBLY
WARNING! Ensure unit is not plugged into the electrical supply before
attempting any assembly.
4.1.
Attach the side handle or 'D' handle (fig.1). Note: there is a mounting
hole on either side to suit the application and/or operator.
4.2.
Fit the backing pad by screwing it onto the spindle, locking the spindle
by use of the lock button (fig.1)
NOTE: the spindle is fitted with a left-hand thread.
4.3.
The backing pad will accept hook & loop abrasive discs.
5. OPERATION
WARNING! Ensure you read, understand and apply the safety
instructions in Section 1.
Ensure the power control switch is NOT locked on before plugging
into the electrical supply.
5.1.
To select the speed rotate the speed selector switch (fig.4) to the
required setting.
Speed Settings: 600-3200rpm (6 steps).
5.2.
To start the polisher: squeeze the trigger. If required, the trigger
may be locked on by pressing the lock button. To release, squeeze
the trigger again.
WARNING! The high speed settings are intended for sanding. If
used for polishing an excessive amount of surface material may
be removed.
Note: As the rubber support disc is flexible, when sanding it should
not be used head on, but at an angle of approximately 10 to 20
degrees.
Contact your Sealey Stockist for details of compound heads and
lambswool bonnets.
© Jack Sealey Limited
fig.1
fig.2
Original Language Version
MS925PS
Issue: 1 - 29/11/16
Advertisement
