1. Manuals
  2. Brands
  3. vita Manuals
  4. Coffee Maker
  5. VACUMAT 6000 MP
  6. Operating manual

vita VACUMAT 6000 MP Operating Manual

Hide thumbs Also See for VACUMAT 6000 MP:
Table of Contents

Advertisement

Quick Links

See also: Operating Manual , Manual
VITA VACUMAT 6000 MP
Operating manual
VITA shade taking
VITA shade communication
VITA shade reproduction
VITA shade control
Date of issue: 01.13
VITA shade VITA made.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VACUMAT 6000 MP and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for vita VACUMAT 6000 MP

Summary of Contents for vita VACUMAT 6000 MP

  • Page 1 VITA VACUMAT 6000 MP Operating manual VITA shade taking VITA shade communication VITA shade reproduction VITA shade control Date of issue: 01.13 VITA shade VITA made.

  • Page 2: Table Of Contents

    2 Delivery scope 2.1 Control unit 2.2 Accessories (can be purchased separately) 3 Technical information 3.1 General description of the VITA VACUMAT 6000 MP furnace 4 Technical data 4.1 Dimensions/ Weights 4.1.1 VITA VACUMAT 6000 MP furnace 4.2 Electrical specifications 4.2.1 Furnace...

  • Page 3: Introduction

    VITA VACUMAT 6000 MP 1 Introduction Dear Customer, Thank you for deciding to purchase our VITA VACUMAT 6000 MP with pneumatic pressing mechanism. This tried and tested heating system for dental ceramic furnaces, with its quartz/ Kanthal firing muffle and a newly developed insulating material in the firing chamber, is your guarantee of many years of constant firing results with all types of ceramic materials.

  • Page 4: Delivery Scope

    6000 M / 6000 MP. An additional switchbox and connection cable is required for the operation of 2 or more VITA VACUMAT 6000 M / 6000 MP with a VITA vPad comfort, VITA vPad excellence or VITA vPad clinical control unit.

  • Page 5: Technical Information

    VITA VACUMAT 6000 MP Technical information General description of the VITA VACUMAT 6000 MP furnace • High-performance technology with highest temperature accuracy for optimal firing results • Convenient time-saving operation, modest spatial requirements • Sheet steel casing with a painted or stainless-steel finish •...

  • Page 6: Intended Use

    VITA VACUMAT 6000 MP 5 Intended use Basic information on the device construction The device is constructed according to a state of the art design and recognized safety regulations. However, if it is used inappropriately, hazards for the health and safety of the user or third parties may arise as well as the risk of damaging the device and other valuable assets.

  • Page 7: Ambient Conditions

    VITA VACUMAT 6000 MP 7 Ambient conditions • Indoor use • Ambient temperature: 2 °C to 40 °C • Relative humidity: 80% at 31 °C • Maximum altitude: 3,800 m • Rated voltage fluctuations must not exceed plus/minus 10 % of the rated voltage.

  • Page 8: Installation And First Use

    VITA VACUMAT 6000 MP 9 Installation and first use 9.1 Installation location • Install the device in a dry, heated room. The distance to the closest wall should be at least 25 cm. (see sect. 7. Ambient conditions) • When the temperature is below 15 °C (59 ºF) (e.g. after transport), leave the device to stand for approx.

  • Page 9: Compressed Air Connection

    The pressure supplied to the device should be adjusted to a maximum of 5 bar. About the settings for the press pressure see operating manual of VITA vPad excellence / comfort (see sect. 18.3) 9.4 Status display The status display indicates following operation status: •...

  • Page 10: Connecting The Device To The Mains Power Supply

    VITA VACUMAT 6000 MP Never start up the device without the firing socket attached. In continuous operation (max. final temperature, max. firing time), some parts of the firing chamber may reach high temperatures (above 70 °C (158 ºF)). Do not reach into the open firing chamber when the device is switched on.

  • Page 11: Cleaning The Furnace

    VITA VACUMAT 6000 MP 10 Cleaning the furnace Before each cleaning operation, remove the power supply plug! It is not necessary to clean the inside of the firing chamber. Cleaning the casing of the firing chamber at regular intervals with a damp cloth contributes to its operating safety.

  • Page 12: Mains Power Supply Failure

    The warranty and liability comply with the terms and conditions set in the contract. In the event of software modifications without the knowledge and approval of VITA Zahnfabrik H. Rauter GmbH & Co. KG, all liability and warranty claims are invalidated. 14.1 Spare parts Spare parts must comply with the technical requirements determined by the manufacturer.

  • Page 13: Alphabetical Order Of Contents

    VITA VACUMAT 6000 MP 15 Alphabetical order of contents Accessories Pictograms Ambient conditions Power supply failure protection Authorized modes of operation Safety features Safety instructions CE mark Service Cleaning the device Spare parts Cleaning work Status display Compressed air connection...
  • Page 14 With the unique VITA SYSTEM 3D-MASTER all natural tooth shades are systematically determined and completely repro- duced. Please note: Our products should be used according to the working instructions. We cannot be held liable for damages resulting from incorrect handling or usage.

Table of Contents